Download
Share
Print this page
Dell Pro E2225HM Disassembly Manual
  1. Manuals
  2. Brands
  3. Dell Manuals
  4. Monitor
  5. Pro E2225HM
  6. Disassembly manual
Dell Pro E2225HM Disassembly Manual

Dell Pro E2225HM Disassembly Manual

22" monitor
Hide thumbs Also See for Pro E2225HM:

Advertisement

Quick Links

Download this manual
Dell Pro 22 Monitor
E2225HM
Teardown Instruction
Model: E2225HM
Regulatory Model: E2225HMt/E2225HMo
March 2025
Rev. A00

Advertisement

loading
Need help?

Need help?

Do you have a question about the Pro E2225HM and is the answer not in the manual?

Questions and answers

Related Manuals for Dell Pro E2225HM

Summary of Contents for Dell Pro E2225HM

  • Page 1 Dell Pro 22 Monitor E2225HM Teardown Instruction Model: E2225HM Regulatory Model: E2225HMt/E2225HMo March 2025 Rev. A00...

  • Page 2: Notes, Cautions, And Warnings

    A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2025 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.

  • Page 3: Table Of Contents

    Contacting Dell ........

  • Page 4: Safety Instructions

    Safety instructions Use the following safety guidelines to protect your monitor from potential damage and to ensure your personal safety. Unless otherwise noted, each procedure in this document assumes that you have read the safety information that shipped with your monitor.

  • Page 5: Disassembly And Reassembly

    Disassembly and reassembly CAUTION: The information in this section is intended for authorized service technicians in the EMEA region. Dell prohibits users from disassembling the monitor, and any damage that is caused by unauthorized servicing will not be covered under the warranty.

  • Page 6: Stand

    Stand Removing the stand Prerequisites 1. Follow the procedure in Before working inside your monitor. Figure 1. Removing the stand Steps 1. Place the monitor on a soft cloth or cushion on the desk. 2. Use a long, thin screwdriver to push the release button. 3.

  • Page 7: Back Cover

    3. Place the monitor on a soft cloth or cushion near the edge of the desk. 4. Align the stand assembly bracket with the monitor groove. 5. Insert the stand assembly towards the monitor until it locks in place. Next steps 1.

  • Page 8: Main Chassis

    Steps 1. Align the slots on the back cover with the slots on the main chassis, then press along the sides to snap the back cover into place. 2. Replace the two screws (M4x6) that secure the back cover to the display monitor. Next steps 1.
  • Page 9 Figure 6. Removing the main chassis Steps 1. Remove the three screws (M3x3) that secure the main chassis to the display panel. 2. Remove the two screws (M3x8) that secure the VGA connector to the main chassis. 3. Peel the acetate tape and disconnect the lightbar cable from the connector on the display panel. 4.

  • Page 10: Installing The Main Chassis

    Installing the main chassis Figure 7. Installing the main chassis...
  • Page 11 Figure 8. Installing the main chassis Steps 1. Connect the LVDS cable to the connector on the display panel. 2. Adhere the aluminum foil to cover the LVDS connector. 3. Align the holes on the main chassis with the screw holes on the display panel and place it down. 4.

  • Page 12: Middle Frame

    Middle frame Removing the middle frame Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the main chassis. Figure 9. Removing the middle frame Steps 1. Remove the nine screws (M3x5) that secure the middle frame to the display panel. 2.

  • Page 13: Installing The Middle Frame

    Installing the middle frame Figure 10. Installing the middle frame Steps 1. Align the screw holes on the middle frame with the holes on the display panel and place it down. 2. Replace the nine screws (M3x5) that secure the middle frame to the display panel. Next steps 1.

  • Page 14: Installing The Keypad Board

    Figure 11. Removing the keypad board Steps 1. Peel the Mylar tape from the middle frame. 2. Remove the three screws (M2x3.3) that secure the keypad board to the middle frame. 3. Remove the keypad board from the slots of the middle frame. Installing the keypad board Figure 12. Installing the keypad board...

  • Page 15: Main Board

    Main board Removing the main board Prerequisites 1. Follow the procedure in Before working inside your monitor. 2. Remove the stand. 3. Remove the back cover. 4. Remove the main chassis. 5. Remove the middle frame. 6. Remove the keypad board.

  • Page 16: Installing The Main Board

    Steps 1. Remove the screw (M3x6) on the main board that secures the Mylar sheet and the main board to the main chassis. 2. Remove the Mylar sheet from the slots of the main chassis. 3. Remove the screw (M3x6) and the screw (M4x8) that secure the main board to the main chassis. 4.
  • Page 17 Next steps 1. Install the keypad board. 2. Install the middle frame. 3. Install the main chassis. 4. Install the back cover. 5. Install the stand. 6. Follow the procedure in After working inside your monitor.

  • Page 18: Contacting Dell

    Contacting Dell To contact Dell for sales, technical support, or customer service issues, see www.dell.com/contactdell. NOTE: Availability varies by country and product, and some services may not be available in your country. NOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip,...