Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Saniselect H140000001
Summary of Contents for Saniselect H140000001
- Page 1 User manual H140000001...
-
Page 2: Table Of Contents
1. Power and water failure 2. Failure of remote control • Seat disassembly and installation • Description of the button function • LED display description (Only for the toilet with LED display) • Troubleshooting guide • Warranty card User manUal H140000001... -
Page 3: Warranty Conditions
User manUal Warranty conditions SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING When using electrical products, especially when children are present, basic safety precautions should always be followed, including the following: 1. The appliance is not to be used by persons (including WARNING –... -
Page 4: Grounding Instructions
User manUal Warranty conditions GROUNDING INSTRUCTIONS CAUTION - Failure to follow the instructions may cause bodily injury or property damage. This product should be grounded. In the event of an electrical 1. Do not install or use the product in wet places such as a short circuit, grounding reduces the risk of electric shock by steam room etc. -
Page 5: Main Unit
User manUal Technical specification Model CH10023ZXR Rated voltage 220V-240V, 50Hz-60Hz 1010W (Without seat temperature function) Rated power Main Unit 1055W (With seat temperature function) Water proof IPX4 Water pressure range 0.08MPa - 0.8MPa (static pressure) Flush volume 6.0L(full ush)/4.0L(half ush) Flushing mode Washdown Toilet... - Page 6 User manUal Technical specification Surface temperature 6-level adjustment (Neutral level included) Heating power Heated seat After 10 minutes of use, the seat temperature (optional) Burn protection will automatically drop slowly to a low level Seat sensor, temperature sensor, thermal fuse, Safety device thermostat, leakage protection device Sterilization...
- Page 7 User manUal Parts identification Bumper Button Seat Ceramic toilet Touch the sensing area with foot (optional) Bumper Drying shield Nozzle shield Spray nozzle Rear washing Front washing Night light sensor User manUal Parts identification...
- Page 8 User manUal Preparation / Pre-installation confirmation Before use, press the reset switch and the button light will light up, indicating power on. Warm reminder: Press the test button before use. The reset switch pops up, indicating that the leakage protection function is normal. ON: Reset switch OFF: Test button Lid auto open/close...
-
Page 9: Maintenance
User manUal maintenance Main unit care and maintenance Spray nozzle care and maintenance 1. Shut off power supply before doing maintenance. 1. When no one is seated, short press “REAR/MOVE” Button 2. Use only a soft, damp cloth to clean. Avoid using harsh on the main unit, the nozzle will automatically stretch out chemicals. -
Page 10: Filter Maintenance
User manUal maintenance / maintenance Precautions Filter maintenance When the bidet malfunctions, maintain it according to the following methods: If poor spray performance occurs under normal conditions: 1. Turn off power and ball valve, unscrew water supply hose. 1. Drain the water inside the bidet: Please refer to the remote control manual for specific operations. -
Page 11: Water Tank Descaling
User manUal Water tank descaling / Emergency troubleshooting Main unit care and maintenance Power and water failure (Only for the toilet with descaling function) Put around 8L water into a barrel and flush the ceramic bowl. You will need to descale the toilet after 3-6 months of use. Note: Avoid water spilling from bowl. -
Page 12: Seat Disassembly And Installation
User manUal Seat disassembly and installation Seat disassembly Seat installation 1. Open seat at 90°. 1. Fit seat at 90°. 2. Press down button on the left side, button pops out and 2. Insert the right hinge first and then the left. seat unlocks. - Page 13 User manUal Description of the button function When seated, short press Stop Button to stop front washing, rear washing or drying functions; When no one is seated, repeatedly press Stop Button, the main unit will switch between functional mode Stop (white light always on) and energy saving mode (white light ashing).
- Page 14 User manUal leD display description (Only for the toilet with leD display) sterilization water temperature temperature display descaling ECO energy saving Description of LED display: 1. During self-inspection, icons of sterilization, water temperature, descaling and ECO light up, and the temperature is displayed at 88 .
-
Page 15: Troubleshooting Guide
User manUal Troubleshooting guide Problem Cause Solution Water supply hose is kinked Straighten the hose to remove the kink No water from Angle valve is o Turn on the angle valve nozzle A water failure occurred Restore the water supply Water supply hose is kinked Straighten the hose to remove the kink Poor water... -
Page 16: Product Warranty Card
User manUal Product warranty card Model No. Customer Name Seller Purchasing Date Invoice No. Customer Contact Distributer Stamp Distributer Phone Thank you for choosing our product. This product is warranted for three (3) years since the purchasing date for free repair of problems arising out of defects in workmanship while using in accordance with installation manual and usage cations for intended purposes. - Page 17 Fabrikant Ben Design Worldwide Gragtmansstraat 3 5145 RA Waalwijk Distributeur De Badenman Van Harenstraat 1 5145 RH Waalwijk Manufacturer Ben Design Worldwide Gragtmansstraat 3 5145 RA Waalwijk Distributor De Badenman Van Harenstraat 1 5145 RH Waalwijk Hersteller Ben Design Worldwide Gragtmansstraat 3 5145 RA Waalwijk Verteiler...
Need help?
Do you have a question about the H140000001 and is the answer not in the manual?
Questions and answers