Advertisement

General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights
reserved. The whole or any part of this publication may not be reproduced, stored
in a retrieval system, translated, transcribed, or transmitted, in any form, or by
any means, manual, electric, electronic, electromagnetic, mechanical, chemical,
optical or otherwise, without prior explicit written permission of Omnitron Systems
Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.:
FlexPoint
, FlexSwitch
, iConverter
, miConverter
, NetOutlook
, OmniLight
,
®
TM
®
®
®
®
OmniConverter
, RuggedNet
, Omnitron Systems Technology, Inc.
, OST
and
®
®
TM
TM
the Omnitron logo.
OmniConverter
®
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice.
GPoEBT/S
Omnitron Systems Technology, Inc. is not responsible for any inadvertent errors.
Warranty
This product is warranted to the original purchaser (Buyer) against defects in
material and workmanship for a period of two (2) years from the date of shipment.
A lifetime warranty may be obtained by the original purchaser by registering this
product at www.omnitron-systems.com/support within ninety (90) days from the
date of shipment. During the warranty period, Omnitron will, at its option, repair or
replace a product which is proven to be defective with the same product or with a
product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility,
User Manual
at Buyer's expense. Omnitron will pay the shipping charge to return the product to
Buyer's designated US address using Omnitron's standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to product malfunctions resulting from
improper or inadequate use and/or maintenance of the equipment by Buyer, Buyer-
supplied equipment, Buyer-supplied interfacing, unauthorized modifications or
tampering with equipment (including removal of equipment cover by personnel not
specifically authorized and certified by Omnitron), or misuse, or operating outside
the environmental specification of the product (including but not limited to voltage,
ambient temperature, radiation, unusual dust, etc.), or improper site preparation
or maintenance.
No other warranty is expressed or implied. Omnitron specifically disclaims the implied
warranties of merchantability and fitness for any particular purpose.
The remedies provided herein are the Buyer's sole and exclusive remedies. Omnitron
shall not be liable for any direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any legal theory.
38 Tesla, Irvine, CA 92618 USA
Phone: (949) 250-6510; Fax: (949) 250-6514
Page 2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OmniConverter GPoEBT/S and is the answer not in the manual?

Questions and answers

Summary of Contents for Omnitron Systems OmniConverter GPoEBT/S

  • Page 1 Omnitron Systems Technology, Inc. The following trademarks are owned by Omnitron Systems Technology, Inc.:...
  • Page 2: Environmental Notices

    Product Overview Directive) of the European Community directive 2012/19/EU on waste electrical and The OmniConverter GPoEBT/S is a multi-port High-Power PoE Ethernet media converters electronic equipment (WEEE) which, together with the RoHS Directive 2015/863/ that feature one or two uplink ports and one or two 10/100/1000 RJ-45 copper PoE ports.
  • Page 3 The table below provides a description of each DIP-switch position and function The table below provides a description of each DIP-switch position and function for Dual Uplink Ports. for Single Uplink Ports. Function Function Switch Position Switch Position 2 SFP + 2 RJ-45 + 2 LC + 2 SFP +...
  • Page 4: Sw1 And Sw2: Mode Of Operation

    Protected SW1 and SW2: Mode Of Operation Protected mode is only available on models with two uplink ports. The modules support different modes based on the port configuration. See below. When SW1 is in the UP position and SW2 is in the DOWN position, the module is 2 Uplink Ports + 2 Uplink Ports + 1 Uplink Ports +...
  • Page 5 SW10 and SW11 The module can be configured to disable (reset) the PoE output power for 2 seconds Switch SW3 configures the speed of the Uplink port. For SFP models, the module after a loss of receive link on any uplink port. This feature is typically used to allow will determine the speed of the installed SFP based on the MSA compliant speed/ a PD to re-initialize after a failure on the incoming fiber.
  • Page 6 2) Installing the Module Installation of the equipment should be such that the air flow in the front, back, side Please contact Omnitron Systems for Conformal Coated products that can be and top vents of the chassis are not compromised or restricted.
  • Page 7 Appropriate overloading protection should be provided on the DC power source WARNING!!! outlets utilized. NEVER ATTEMPT TO OPEN THE CHASSIS OR The GPoEBT/S requires 52 to 57VDC @ 3.67 Amp max rated power (see SERVICE THE POWER SUPPLY. OPENING THE specification table for specific model requirements).
  • Page 8 5) Verify Operation PoE RJ-45 Port Indicators Verify the module is operational by viewing the LED indicators. Legend Indicator Description Port not linked at 10Mbps Power LED Indicators Green - ON Port linked at 10Mbps Full Duplex Legend Indicator Description (Both 100 + Green - Blinking at 10Hz Port is transmitting or receiving frames at full duplex...
  • Page 9 MECHANICAL Ventilation holes may vary Page 17 Page 18...
  • Page 10: Specifications

    -40 to 60°C (-20°C AC cold start) Fax: (949) 250-6514 (See Temperature Derating Extended: -40 to 75°C (-20°C AC cold start) Table) Address: Omnitron Systems Technology, Inc. Storage: -40 to 80°C Humidity 5 to 95% (non-condensing) 38 Tesla Altitude -100m to 4,000m...

Table of Contents