Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Flexitron Webdyn EasyDot
Summary of Contents for Flexitron Webdyn EasyDot
- Page 1 Webdyn EasyDot Hardware manual www.webdyn.com...
-
Page 2: Table Of Contents
RF Signal Strength ............................. 29 Panel mounting ............................29 DIN Rail mounting ............................30 Connections of EasyDot ..........................31 Support ............................ 32 Sales and Support ........................33 contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 3: General Notes
Spanish law without reference to any other substantive law. Important Information This technical description contains important information for the start-up and use of the Webdyn EasyDot gateway. Read it carefully before you start working with the EasyDot gateway. The warranty will be void should damage occur due to non-compliance with these instructions for use. -
Page 4: Revision Information
Parliament and of the Council of 27 January 2003 (and revised on 8 June 2011) on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS). contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 5: Ce Mark
1.25A fuse should be connected in line with the positive supply. Only compatible components should be connected to EasyDot. Note! EasyDot distributors and sales offices may refuse warranty claims where evidence of product misuse is found. contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 6: Safety Requirements And Protection Regulations
In applications where this rule cannot be applied, the application designer is responsible for providing the SAR measurement test report and declaration. You are responsible for observing your country’s safety standards, and where applicable, the relevant wiring rules. contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 7: Sim Card Precautions
SAR regulatory requirements of the countries in which they intend to operate the device and that their documentation contains the relevant SAR declaration, certification information and user guidance as appropriate. contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 8: Sar Information
1995.26 / 33 1.79 1995.26 / 33 9.75 1800 1000 / 30 4.79 1800 1000 / 30 14.97 2600 199.52 / 23 14.01 2600 199.52 / 23 21.97 contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 9: Personal Medical Devices
To comply with RED regulations, the following antenna considerations must be complied with: The antenna used for LTE communications must be less than 0.49 dBi Gain of an isotropic antenna. contact@webdyn.com | webdyn.com V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 10: Technical Description
4G technology. A full list of supplied antennas, cables, and accessories are available. contact@webdyn.com | webdyn.com | 10 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 11: Operating Range
SIM Card Slot ESD protection ±15kV (Contact) Antenna LTE antennas 50 ohms Cellular output power Max. GSM850/EGSM900 33 dBm DCS1800/PCS1900 30 dBm LTE bands 23 dBm contact@webdyn.com | webdyn.com | 11 V1.00 subject to change | Webdyn © by Flexitron Group... - Page 12 Radio spectrum and radio network are not influenced, while one or more specifications, such as Pout, may exceed the specified tolerances of 3GPP. contact@webdyn.com | webdyn.com | 12 V1.00 subject to change | Webdyn © by Flexitron Group...
-
Page 13: Ordering Information
RoHS symbol Pb-Free logo WEEE logo CE logo Product name (model) Part number/ordering code (P/N) Manufacturing Year/week (YYMM) IMEI IMEI Bar Code Power supply operating specifications contact@webdyn.com | webdyn.com | 13 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 14: System Architecture
000199811008 Webdyn EasyDot NETWORK BANDS TECHNOLOGY MAX DATA RATE MAX DATA RATE B1/B3/B5/B7/B8 LTE-FDD 10 Mbps 5 Mbps /B20/B28 B2/B3/B5/B8 GPRS 85.6 kbps 85.6 kbps contact@webdyn.com | webdyn.com | 14 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 15: External Interfaces On Front And Rear Panel
Power supply input – 2-way plug-in 3.5mm pitch terminal block RS485 interface - 2-way plug-in 3.5mm pitch terminal block Mini USB type B configuration port Factory Default Settings push button contact@webdyn.com | webdyn.com | 15 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 16: Power Connection
Power supply input is externally connected on terminal block, positive signal at pin 1 and negative signal at pin 2. Operating range values are specified at (Operating range). contact@webdyn.com | webdyn.com | 16 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 17: Main Antenna Connection
Antenna connector should be SMA Male type Antenna power should be at least 500mW as maximum power is 316.23mW. Maximum Output RF load mismatch ruggedness at antenna is 10:1 VSWR contact@webdyn.com | webdyn.com | 17 V1.00 subject to change | Webdyn © by Flexitron Group... - Page 18 Hand-over occurs as you move from one cell to another in the GSM network. Your mobile application call is transferred from one cell to the next. Hand-over can briefly interfere with communication and may cause a delay, or at worst, disruption. contact@webdyn.com | webdyn.com | 18 V1.00 subject to change | Webdyn © by Flexitron Group...
-
Page 19: Sim Card Reader
To insert Mini SIM card, look at the picture below for proper orientation. contact@webdyn.com | webdyn.com | 19 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 20: Mini Usb Type B Port
USB. Currently, this interface is only compatible with Windows operating systems and other systems that natively support the RNDIS protocol. EasyDot has by factory default IP: 192.168.1.1 – Mask: 255.255.255.0 contact@webdyn.com | webdyn.com | 20 V1.00 subject to change | Webdyn © by Flexitron Group... - Page 21 Use the default username and password: admin and admin Through which we can configure Titan RS232, RS485, Sim, MODBUS, etc. See µTitan software manual for more information. contact@webdyn.com | webdyn.com | 21 V1.00 subject to change | Webdyn © by Flexitron Group...
-
Page 22: Rs232 Connection
Not connected RS232 RTS Ready to send Reference common signal Not connected RS232 Tx Data received on this input is transmitted to WAN contact@webdyn.com | webdyn.com | 22 V1.00 subject to change | Webdyn © by Flexitron Group... - Page 23 RS232 LEDS Green Blink Transmitting Data Amber Blink Receiving Data contact@webdyn.com | webdyn.com | 23 V1.00 subject to change | Webdyn © by Flexitron Group...
- Page 24 Recommended cable to convert the RJ45 to DB9 Male (commonly used in electricity meters). This is the pin-out of the cable: Recommended Webdyn accessory cable: Model Name Part Number Cable modem (RS232/RS485/RS422) [RJ45] to [DB9M] 000230001103 contact@webdyn.com | webdyn.com | 24 V1.00 subject to change | Webdyn © by Flexitron Group...
-
Page 25: Rs485 Connection
Internal Resistors on RS485 Fail-Safe Bias ESD Protection 16 KV air / 16 KV contact Cable length Max. 3 m with UTP cable Max. 20 m with SFTP cable contact@webdyn.com | webdyn.com | 25 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 26: Status Leds
Mini SIM undetected or incorrect PIN Not enough/critical coverage Low coverage Blink Good coverage IP Status LED (Blue) Operating States State IP Not Assigned IP Assigned contact@webdyn.com | webdyn.com | 26 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 27: Factory Default Settings Reset
Wait for EasyDot to restart, and for the Coverage LED (yellow LED) and IP Status LED (blue LED) to start blinking. It may require around 15 seconds. Release “Factory default settings” button. Power off the EasyDot gateway. Power on again. contact@webdyn.com | webdyn.com | 27 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 28: Mechanical Description
3 Mechanical Description 3.1 Dimensions contact@webdyn.com | webdyn.com | 28 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 29: Device Installation
To install the device on a wall, place the EasyDot parallel to the wall as shown in the image, and use the holes provided to insert the fastening elements. contact@webdyn.com | webdyn.com | 29 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 30: Din Rail Mounting
DIN rail in two positions to best adapt the EasyDot to the cabinet where it will be installed. Model Name Part Number EasyDot Din rail accessory 000199804000 contact@webdyn.com | webdyn.com | 30 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 31: Connections Of Easydot
This protects the power cabling and gateway. The figures below show connections for all available interfaces; however, only those required for the end application should be connected. contact@webdyn.com | webdyn.com | 31 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 32: Support
Product serial number. Production date. Software version of the product. Hub logs Gateway configuration The user manual and firmware are available at this web address: https://www.webdyn.com/support/TBD contact@webdyn.com | webdyn.com | 32 V1.00 subject to change | Webdyn © by Flexitron Group... -
Page 33: Sales And Support
803-804 8th floor, Vishwadeep Building District Centre, Janakpurt, 110058 Delhi Telephone: +91.1141519011 E-mail: contact@webdyn.com PORTUGAL Av. Coronel Eduardo Galhardo 7-1ºC 1170-105 Lisbonne Telephone: +351.218162625 E-mail: comercial@lusomatrix.pt contact@webdyn.com | webdyn.com | 33 V1.00 subject to change | Webdyn © by Flexitron Group...
Need help?
Do you have a question about the Webdyn EasyDot and is the answer not in the manual?
Questions and answers