VTech Switch&Go Dinos Manual

INTRODUCTION

My name is Blister the Velociraptor, and I'm looking for a few good dinos to join my squad. But let me warn you – you've got to be at your best to keep up with me! I'm fast and ferocious with sharp, curved claws that make me as tough as any dino.
I make a pretty tough helicopter too! I patrol the skies with my searchlight shining down from above. Once I've got a target in my sights, there's nowhere for it to hide!

INCLUDED IN THIS PACKAGE

• One VTech^® SWITCH & GO DINOS^® Blister the Velociraptor
• One parent's guide

All packing materials such as tape, plastic sheets, packaging locks, removable tags, cable ties and packaging screws are not part of this toy and should be discarded for your child's safety.
NOTE:
Please keep this parent's guide as it contains important information.

GETTING STARTED

BATTERY INSTALLATION

1. Make sure the unit is turned OFF.
2. Locate the battery cover on the bottom of the unit. Use a screwdriver to loosen the screw.
   
3. Install 2 new AA (LR6/AM-3) batteries into the main unit following the diagram inside the battery box. (The use of new, alkaline batteries is recommended for maximum performance).
4. Replace the battery cover and tighten the screw to secure.

BATTERY NOTICE

• Use new alkaline batteries or fully charged NI-MH (Nickel Metalhydride) rechargeable batteries for best performance.
• Use only batteries of the same or equivalent type as recommended.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or rechargeable, or new and used batteries.
• Do not use damaged batteries.
• Insert batteries with the correct polarity.
• Do not short-circuit the battery terminals.
• Remove exhausted batteries from the toy.
• Remove batteries during long periods of non-use.
• Do not dispose of batteries in fire.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the toy before charging (if removable).
• Rechargeable batteries are only to be charged under adult supervision.

PRODUCT FEATURES

1. ON/OFF SWITCH
   Slide the ON/OFF Switch to ON () to turn the unit ON. Slide the ON/OFF Switch to OFF () or hold the Talk Button for a few seconds to turn the unit OFF.
   
2. STYLE BUTTON
   Press the Style Button to select the dino eyes you prefer in dino mode.
   
   Press the Style Button to select the pilot you prefer in helicopter mode.
   
3. TALK BUTTON
   Press the Talk Button to hear the dino or pilot talk.
   
4. SOUND BUTTON
   Press the Sound Button to hear cool sound effects.
   
5. VOLUME BUTTON
   Press the Volume Button to adjust the volume.
   There are four levels available: low, medium, high, and mute.
   
6. SEARCHLIGHT BUTTON
   Press the Searchlight Button to turn on the searchlight.
   
7. LAUNCH BUTTON
   Press the Launch Button to launch the rocket.
   
8. ROTOR BLADES BUTTON
   Press the Rotor Blades Button to spin the rotor blades.
   
9. MOTION SENSOR
   Move the helicopter through the air to hear fun flying sounds!
10. AUTOMATIC SHUT-OFF
    To preserve battery life, the unit will automatically shut-off after several minutes without input.

HOW TO SWITCH THE BLISTER

1. Velociraptor mode.
   
2. Move the head up.
   
3. Move the launcher across.
   
4. Fold the arms.
   
5. Move the tail down.
   
6. Flip the rotor blades to the front of the helicopter.
   
7. Spread the rotor blades.
   
8. Turn the rear wing at the end of the tail forward.
   
9. Flip the legs up.
   
10. Turn the feet up.
    
11. Move the wings down.
    
12. Helicopter mode.
    

Note: To change the helicopter back into a dino, reverse the order of the steps above.

CARE & MAINTENANCE

1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct heat source.
3. Remove the batteries when the unit is not in use for an extended period of time.
4. Do not drop the unit on hard surfaces and do not expose the unit to moisture or water.

TROUBLESHOOTING

If for some reason the program/activity stops working or malfunctions, please follow these steps:

1. Please turn the unit OFF.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit ON. The unit should now be ready to play with again.
5. If the product still does not work, install a brand new set of batteries.

If the problem persists, please contact our Consumer Services Department and a service representative will be happy to help you.

CONSUMER SERVICES

Creating and developing VTech^® products is accompanied by a responsibility that we at VTech^® take very seriously. We make every effort to ensure the accuracy of the information, which forms the value of our products. However, errors sometimes can occur. It is important for you to know that we stand behind our products and encourage you to call our Consumer Services Department with any problems and/or suggestions that you might have. A service representative will be happy to help you.

UK Customers:
Phone: 0330 678 0149 (from UK) or +44 330 678 0149 (outside UK)
Website: www.vtech.co.uk/support
Australian Customers:
Phone: 1800 862 155
Website: support.vtech.com.au
NZ Customers:
Phone: 0800 400 785
Website: support.vtech.com.au
Visit our website for more information about our products, downloads, resources and more.
www.vtech.co.uk
www.vtech.com.au