Advertisement
Advertisement
Table of Contents
Related Manuals for Vivo PP-DK04F
Summary of Contents for Vivo PP-DK04F
- Page 1 Pegboard Desk Organizer PP-DK04F Assembly Manual...
- Page 2 If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact our product support team at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement.
-
Page 3: Package Contents
Package Contents B (x2) C (x1) A (x1) Small Bin Pegboard Wire Post D (x1) E (x1) F (x1) Large Bin Tray Stand Weight Capacity: W-A (x2) W-B (x2) S-A (x2) ST4.2x35mm 13x40mm Thumbscrew Screw Drywall Anchor S-B (x2) S-C (x4) Rubber Pad Soft Pad Tools Needed:... -
Page 4: Mounting Options
Mounting Options Determine your intended mounting surface and follow instructions as identified below. -
Page 5: Assembly Steps
Assembly Steps STEP 1 Option 1: Freestanding Base Insert Pegboard (A) into the Stand (F). Proceed to STEP 2 on Page 11... - Page 6 Option 2: Door/Wall Hanging Remove the adhesive backing and place the Soft Pads (S-C) onto the back of the Pegboard (A). Make sure not to block any holes with Soft Pads (S-C). Insert Thumbscrews (S-A) into the back of Pegboard (A). Once threaded through, place Rubber Pads (S-B) onto the tip of the Thumbscrews.
-
Page 7: Option 3: Drywall Mounting
Option 3: Drywall Mounting Position Pegboard (A) at desired location and mark the hole locations with a pencil. Tap 13x40mm Drywall Anchors (W-B) partially into marked hole locations, then use a Phillips screwdriver to fully screw in the Anchors. Insert ST4.2x35mm Screws (W-A), leaving 7mm of the threading exposed. - Page 8 Option 3: Drywall Mounting - Cont’d Screw the Thumbscrews (S-A) onto the back of the Pegboard (A), then hang the Pegboard onto the wall. Tighten ST4.2x35mm Screws (W-A) with a Phillips screwdriver. Proceed to STEP 2 on Page 11...
- Page 9 Option 4: Wood Wall Mounting Position Pegboard (A) at desired location and mark the hole locations with a pencil. Drill mounting holes at marked locations using the infographic shown. Drill Bit: 1/8” (3mm) Hole Depth: 1.4” (35mm) Insert the ST4.2x35mm Screws (W-A) into the holes and leave 7mm of threading exposed.
- Page 10 Option 4: Wood Wall Mounting - Cont’d Screw the Thumbscrews (S-A) onto the back of the Pegboard (A), then hang the Pegboard onto the wall. Tighten ST4.2x35mm Screws (W-A) with a Phillips screwdriver.
- Page 11 STEP 2 Hook Small Bin (C), Large Bin (D), and Tray (E) onto Pegboard (A) where desired. 1.18” (30mm) 1.18” (30mm) Pegboard accessories from other products may not be compatible with this product. STEP 3 Pinch the Wire Posts (B) and press into Pegboard (A) where desired. Store cords on Posts as desired.
- Page 12 Need Help? We’re Here For You Monday-Friday from 7am-7pm CST Saturday 8am-4pm CST Email Us Chat with Live Agent Give Us a Call help@vivo-us.com www.vivo-us.com 309-278-5303 ext. 1 FOR MORE GREAT VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: WWW.VIVO-US.COM VIVO-us @vivo_us @VIVOus VIVO...
Need help?
Do you have a question about the PP-DK04F and is the answer not in the manual?
Questions and answers