Related Manuals for Wilo Control Fire E VdS
Summary of Contents for Wilo Control Fire E VdS
- Page 1 Pioneering for You Wilo-Control Fire E VdS en Installation and operating instructions · 4248040 • Ed.01/2024-03...
- Page 2 W-CTRL Fire VdS https://qr.wilo.com/1340...
-
Page 3: Table Of Contents
Running the operating modes .......... 17 8 Commissioning................. 18 Carry out commissioning ........... 19 9 Shut-down ................ 20 Decommissioning ............... 20 10 Maintenance................ 20 10.1 Maintenance intervals............ 20 11 Faults, causes and remedies ........... 21 Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 4: General
All rights reserved. Subject to change Wilo shall reserve the right to change the listed data without notice and shall not be liable for technical inaccuracies and/or omissions. The illustrations used may differ from the ori- ginal and are intended as an exemplary representation of the product. -
Page 5: Identification Of Safety Instructions
Personnel have read and understood the installation and oper- ating instructions. • Electrical work: qualified electrician Person with appropriate technical training, knowledge and ex- perience who can identify and prevent electrical hazards. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 6: Electrical Work
• Always attach the lifting gear to the attachment points. • Standing under suspended loads is not permitted. Do not move suspended loads over workplaces where people are present. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 7: Installing/Dismantling
After delivery, check product and packaging for defects (damage, completeness). Delivery • The transport company or the manufacturer must be notified of any defects the day the shipment is received, and the damage noted on the freight documentation. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 8: Transport
The switch cabinet can be installed directly on a pump group or on a wall. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 9: Switchgear
The control panel contains the following: Control panel • Instruments for monitoring and operating the pump and all subassemblies • Graphical user interface with a touchscreen display Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... - Page 10 Mains voltage is normal, power supply is switched on White 4.2.14.1 If the LED does not light up: Check power supply and fuse pro- tection frequency converter 1 + frequency converter 2 Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03...
-
Page 11: Switchgear Door Buttons
QF6 QF7 Relay (KA...) Amperometric transformer (TA...) Main switch (QS1) Terminal strips (M...) Power contactors (KM...) KM4 KM5 QF8 QF9 Circuit breaker (QF...) TA1 TA2 TA3 Fig. 4: Overview of electrical components Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 12: Display
The switchgear has digital and analogue inputs. Designation Input (digital) SLAVE10 Terminal Emergency switch active M1 -6 Jockey pump/pressure-maintaining pump pressure M1 -8 switch IN10 Compressor pressure switch M1 -10 Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 13: Analogue And Digital Inputs
Accessories, depending on order • Jockey pump/pressure-maintaining pump 5.12 Accessories • Pressure switch with pre-assembled resistors • Float switch with pre-assembled resistors • Automatic transfer switch (switchover to 2nd power supply) Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 14: Installation And Electrical Connection
• Carry out the electrical connection according to the circuit diagram in the switchgear. The circuit diagram documentation is stored in the switch cabinet. • The mains connection current and voltage must be as stated on the rating plate. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 15: Operation
Pressure switch start delay for automatic start Reset: Press for 5 seconds for system reset. Change values Status display for inputs and outputs: Slave 10 and slave 11 (full rectangle: active) Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 16: Operating Modes
The emergency start and emergency stop buttons are always active, even if the switchgear has an error. • After the emergency stop has been activated, switch the fuse protection QF1 back on in the switchgear. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 17: Running The Operating Modes
If the fault no longer exists, the fault indicator is automatically reset. Running the operating modes WARNING Risk of injury due to improper operation! • Observe safety information in the installation and operating instruc- tions of the pumps. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... - Page 18 (e.g., no cooling water or no oil). Press the “Manual start” button. Press the “Manual stop” button. Close the stop valve of the test line. ▶ After stopping, the pump group enters automatic mode. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03...
-
Page 19: Commissioning
Activate the automatic start command by lowering the pressure in the discharge line. Press and hold down the motor stop button. • Each start cycle consists of a start phase (10 seconds) followed by a pause of maximum 10 seconds. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 20: Shut-Down
10.1 Maintenance intervals Weekly • Test control lamps. Press the “Lamp test” button. If a control lamp is defective, contact Wilo customer ser- vice. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... -
Page 21: Faults, Causes And Remedies
Check voltage. Check connections and cable cross-sec- tions. The motor does not reach the rated Loose contact in the power contactor Check and repair. speed Error in starting mechanism Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03... - Page 22 Make sure that there are no leakages in the suction line. Check the distance between the suction units if more than one pump is installed. Install anti-vortex plates. Closure on bearings, pump shaft Replace bearings. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03...
- Page 23 Observe the locally applicable regulations! Please consult your local municipality, the nearest waste disposal site, or the dealer who sold the product to you for information on proper disposal. See www.wilo‑recycling.com for more information about recycling. Installation and operating instructions • Wilo-Control Fire E VdS • Ed.01/2024-03...
- Page 28 Local contact at www.wilo.com/contact WILO SE Wilopark 1 44263 Dortmund Germany T +49 (0)231 4102-0 T +49 (0)231 4102-7363 wilo@wilo.com Pioneering for You www.wilo.com...
Need help?
Do you have a question about the Control Fire E VdS and is the answer not in the manual?
Questions and answers