Seametrics IP803 Instructions Manual

Insertion paddlewheel flow sensor

Advertisement

Quick Links

IP800-Series
IP800-Series
Insertion Paddlewheel
Insertion Paddlewheel
Flow Sensor Instructions
Flow Sensor Instructions
ISO
ISO
9001

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the IP803 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Seametrics IP803

  • Page 1 IP800-Series IP800-Series Insertion Paddlewheel Insertion Paddlewheel Flow Sensor Instructions Flow Sensor Instructions 9001...
  • Page 2: Table Of Contents

    Rotor Replacement ..............................Page 11 Signal Troubleshooting .............................Page 11 Sensor Replacement ..............................Page 11 Parts List ..................................Page 12 Troubleshooting Problems ..................................Page 13 Probable Causes ................................Page 13 Things To Try ..................................Page 13 Warranty Seametrics Limited Warranty ..........................Page 14 Seametrics • 253.872.0284 Page 2 seametrics.com...
  • Page 3: General Information

    Seametrics controls and displays. come wet-calibrated. K-factors for saddles are based on factory-testing. Seametrics IP meters are ideal for chemical proportioning applications. For rate and total display, a modular system of electronics can be installed directly on the flow sensor...
  • Page 4: Specifications

    Regulatory Mark *Specifications subject to change • Please consult our website for current data (www.seametrics.com). Kynar is a registered trademark of Arkema, Inc., Viton is a registered trademark of DuPont Corporation. Caution: These flow sensors are not recommended for installation downstream of a boiler feedwater pump where installation fault may expose the flow sensor to boiler pressure and temperature.
  • Page 5: Installation

    If this is a possibility, as attempt to remove the meter. Removal in a flooded vault, a unit modified for immersion should be under pressure may result in damage or serious injury. specified (Option -40), for temprary immersion. Seametrics • 253.872.0284 Page 5 seametrics.com...
  • Page 6: Straight Pipe Recommendations

    IP800 - SERIES INSTRUCTIONS INSTALLATION Straight Pipe Recommendations (X = diameter) Reduced Pipe Two Elbows In Plane Two Elbows, Out Of Plane Expanded Pipe Spiral Flow Propeller Meter Swirling Flow Partially Open Butterfly Valve Seametrics • 253.872.0284 Page 6 seametrics.com...
  • Page 7: Full Pipe Recommendations

    Post-valve cavitation can create air pocket Keeps pipe full at sensor Possible Problem Better Installation Air can be trapped Allows air to bleed off Possible Problem Better Installation Air can be trapped Allows air to bleed off Seametrics • 253.872.0284 Page 7 seametrics.com...
  • Page 8: Connections

    For sensors with on-board electronics, see the manual accompanying the electronic module. RED (+) Low Power: 6-36 Vdc Micropowered: 3.1 - 16 Vdc WHITE Signal BLACK (-) Power FT430 FT430 Pulse Pass-thru 7-45Vdc Supply BLACK WHITE Pulse Responsive Metering Pump Flow Sensor Seametrics • 253.872.0284 Page 8 seametrics.com...
  • Page 9: Ft440

    FT4XX Eqipped with Sensus Board (Side View) Red (Power/Clock) Sensus Tranceiver Black (Ground) Green (Data) Black Green NOTE: A Sensus 2m (6 ft) output cable is prewired to the Seametrics product at the factory. Longer cables are optional. Seametrics • 253.872.0284 Page 9 seametrics.com...
  • Page 10: Operation And Maintenance

    (www.seametrics.com). Pressure vs. Temperature (PVC/Polypro) 10031295 K: 53.6 MF81T-P200 P.S.I. Find Your K-Factor Here If a saddle or weld-type fitting has been ordered, use the K-factor calculator at the bottom of the seametrics.com 60˚ 70˚ 80˚ 90˚ 100˚ 110˚ 120˚...
  • Page 11: Rotor Replacement

    Slowly turn the rotor. Voltage reading should swing between +12 Volts and 0 Volts as the rotor turns. If it does not, the solid-state magnetic sensor is not working properly. Checking for continuity is not a useful test of these sensors. Seametrics • 253.872.0284 Page 11 seametrics.com...
  • Page 12: Parts List

    (requires 2) O-ring 100264 (EPDM) Body See distributor Bearings (includes 2) 103315 Rotor with shaft Order Rotor Repair Kit Rotor repair kit (#13 & 100317 (Kynar®/tungsten carbide) #14 above) 100043 (Kynar®/ceramic) 100556 (Kynar®/silicone carbide) Seametrics • 253.872.0284 Page 12 seametrics.com...
  • Page 13: Troubleshooting

    Wrong time units on flow If using FT430, FT440, or FT520, check left side of indicator display (sec, min, hr, day); change to desired unit Seametrics • 253.872.0284 Page 13 seametrics.com...
  • Page 14: Seametrics Limited Warranty

    SEAMETRICS LIMITED WARRANTY The limited warranty set forth below is given by Seametrics, with respect to Seametrics brand products purchased in the United States of America. Seametrics warrants that products manufactured by Seametrics, when delivered to you in new condition in their original containers and properly installed, shall be free from defects in material and workmanship.
  • Page 15 IP800 - SERIES INSTRUCTIONS Seametrics • 253.872.0284 Page 15 seametrics.com...
  • Page 16 Seametrics • 19026 72nd Avenue South • Kent, Washington 98032 • USA LT-65200040r3.8 20220502 (P) 253.872.0284 • (F) 253.872.0285 • 1.800.975.8153 • seametrics.com 5/2/2022...

This manual is also suitable for:

Ip800 seriesIp807Ip809Ip810bIp813bIp820p ... Show all

Table of Contents