Whirlpool Duet Steam WED94HEX Use And Care Manual page 11

5.
Adjust cycle settings, if desired
Check Lint Screen Sensing
Estimated Time Remaining
High
Medium
Low
Extra Low
Timed Dry Adjust
Air Only
11-cycle model shown
You may adjust different settings, depending on whether you
have selected an Auto Cycle, Manual Cycle, or Steam Cycle.
See the Cycle Guide for detailed information.
NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.
Auto Cycles:
You can select a different dryness level, depending on your
load, by pressing the button for More, Normal, or Less.
Selecting More, Normal, or Less automatically adjusts the
dryness level at which the dryer will shut off. Once a dryness
level is set, it cannot be changed without stopping the cycle.
Automatic cycles give the best drying in the shortest time.
Drying time varies based on fabric type, load size, and
dryness setting.
Manual Cycles:
When you select a Manual Cycle, the default
time appears in the display. Use the s and t
buttons to increase or decrease the time in
1 minute increments. Press and hold to
change the time in 5 minute increments.
The default temperature may be changed
by pressing the Temperature button until the
desired dry temperature is lit.
Quick Refresh with Steam:
Press the Garment # to select the number of garments in
the load (on some models). The dryer will automatically set the
drying time and temperature. For models without Garment #,
the cycle time is preset to 15 minutes and is not adjustable.
6.
Select any additional options
Wrinkle Shield
with Steam
11-cycle model shown
Add additional options such as Static Reduce, Wrinkle Shield/
Wrinkle Shield with Steam and/or EcoBoost by pressing the
button for that option.
NOTE: Not all options and settings are available with all cycles.
Wet Damp Cool Steam Static Done
Down Reduce
8 - 9
6 - 7
More Dry 4 - 5 Loud
Normal Dry 2 - 3 Soft
Less Dry 1 O
Check Lint Screen Sensing
Estimated Time Remaining
Timed Dry Adjust
7.
Press and hold START/PAUSE
to begin cycle
Wrinkle
Shield
Press and hold the START/PAUSE button to begin the cycle.
8.
Remove garments promptly
after cycle is finished
Check Lint Screen Sensing
Estimated Time Remaining
Timed Dry Adjust
11-cycle model shown
Promptly remove garments after cycle
Wet Damp Cool Steam Static
has completed to reduce wrinkling. If
Down
High 8 - 9
you will be unable to remove the load
Medium 6 - 7
promptly, select the Wrinkle Shield/Wrinkle Shield with Steam
Low More Dry 4 - 5
Extra Low Normal Dry 2 - 3
option before pressing START/PAUSE.
Air Only Less Dry 1
Changing the Auto Cycle settings
to increase drying time
If all your loads on all Auto Cycles are consistently not as
dry as you would like, you may change the default
settings to increase the default dryness level.
Your automatic drying settings can be adjusted to adapt to
different installations, environmental conditions or personal
preference. This change is retained and will affect all of your
Automatic cycles, not just the current cycle/load. There
are 3 drying settings, which are displayed using the time
display:
01 Factory preset dryness level.
02 Slightly drier clothes, 15% more drying time.
03 Much drier clothes, 30% more drying time.
To change the drying settings:
NOTE: The settings cannot be changed while the dryer is
running or paused. The dryer must be in standby mode (the
power button is off) to adjust the default settings.
1. Before starting a cycle, press and hold the TEMP button
for 6 seconds.
2. Press the TEMP button to select the dryness level
shown in the time display: 01, 02, or 03.
3. Press START/PAUSE to save the new dryness level
setting.
Wet Damp Cool
Down
High
Medium
Low More Dry
Extra Low Normal Dry
Air Only Less Dry
Done Wrinkle
Reduce Shield
Loud
Soft
O
Steam Static Done Wrinkle
Reduce Shield
8 - 9
6 - 7
4 - 5 Loud
2 - 3 Soft
1 O
Wrinkle Shield
with Steam
11