1. Manuals
  2. Brands
  3. Heritage Manuals
  4. Plumbing Product
  5. Lux Cube Royale M
  6. Construction manual

Heritage Lux Cube Royale M Construction Manual

Hide thumbs

Advertisement

Table of Contents

Heritage™ Lux Cube Royale M
Round Cube MINI 2.0
Check the parts for completeness before assembly!
Check the parts for completeness before assembly!
Check the parts for completeness before assembly!
Construction guide
Construction guide
Construction guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lux Cube Royale M and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Heritage Lux Cube Royale M

Summary of Contents for Heritage Lux Cube Royale M

  • Page 1 Heritage™ Lux Cube Royale M Round Cube MINI 2.0 Construction guide Construction guide Construction guide Check the parts for completeness before assembly! Check the parts for completeness before assembly! Check the parts for completeness before assembly!
  • Page 2 USER MANUAL OF THE SAUNA 1. It is recommended to install the sauna above ground level to prevent the legs of the sauna from coming into direct contact with the ground. Install a water-resistant material, such as bitumen strips, between the legs of the sauna and the base. 2.

  • Page 3: Warranty

    Maintenance of the sauna 1. The interior surfaces of the sauna, the window frames of the steam and washing room, and the frames of interior doors must be treated with a special substance before initial use to protect them from humidity and dirt and extend the useful life of the sauna. Later, this should be done once or twice a year.

  • Page 4: Front View

    ~2179 2060 Front Back 1530 1552 Front view Scale 1 : 30 Round Cube Heritage™ Lux Cube Royale M MINI MINI Back view drw.1...
  • Page 5 ~2179 2122 1530 2038 2030 1960 Scale 1 : 30 2000 2030 1960 Round Cube MINI MINI Heritage™ Lux Cube Royale M drw.2 drw.2...

  • Page 6: Detail List

    ~120 mm ~120 mm ~120 mm ~55 mm B7a door molding will be removed during construction Front wall reinforcment ~45 mm ~45 mm B2.1 B2.2 x 1 set ~89 mm ~85 mm Detail list 1...
  • Page 7 l=~7.9m l=~2.1m l=~1.6m x PlanoXL 7 pcs x PlanoXL 6 pkg Katepal 3T 8 pcs Katepal 3T 5 pkg Detail list 2...
  • Page 8 I9.2 I9.1 K Square woods 45x45mm Front view ~88 mm ~88 mm ~45 mm Detail list 3...
  • Page 9 Name in Nails and screws (Scale 1:2) Area of use Screw size Quantity in. manual Screws 4,5x80 for Spruce x100 Mainly for construction inside and outside Screws 4,2x75 for Thermo S6.2 For fixing the door(s) Screws 4,2x75 Screws 4,5x70 S6.1 For fixing the side wall end coverings (black coated) Screws 4,5x60 for Spruce...
  • Page 10 Screws 4,5x80 for Spruce NB! use a level Screws 4,2x75 for Thermo The base of the sauna must be level! B2.1 mm=mm B2.1...
  • Page 11 Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Use two screws on both sides (see sketch). Please countersink the screw head! mm=mm...
  • Page 12 Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Use a rubber mallet to tap the planks together. Screw each plank B3a and B3b to the foundation B1 with a screw. ~7 pieces on each side left B3a and right B3b. Please countersink the screw head! When the boards are installed, it should look like this.
  • Page 13 Back Front ~64 mm Before installation of the drain pipe, hole must be cut with a hole saw. ~44 mm Install a piece of drain pipe V1.
  • Page 14 Drill 10 mm hole in each plank, in the front wall groove and in the back wall groove to the outside as shown in the picture A1 and A2. After drilling, clean the groove from wood debris and cover the groove with varnish or another protective agent.
  • Page 15 Screws 4,5x80 for Spruce Screws S7 Screws S5 Screws 4,2x75 for Thermo min. 22 mm Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo Preparation of the front wall. When assembling the front wall, first use glue between the wall pieces and then screw the pieces together and add the wall reinforcements B2.2 to the inner side of the wall.
  • Page 16 Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo mm=mm mm=mm First install the lower part of the back wall. The lower part of the back wall must be in the center of the base. If the lower part of the back wall is in place, then it must be fixed with screws.
  • Page 17 Screws 4,5x80 for Spruce Screws S7 Screws 4,2x75 for Thermo When installing the front wall, make sure that it Screws 4,5x60 for Spruce stays in the center! Screws 4,2x55 for Thermo NB! use a level Screws S7 To keep the front wall upright, use the side wall boards B3a and B3b.
  • Page 18 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo When the front wall is attached, start building the side walls on the left B3a and on the right B3b. Use a rubber mallet to tap the boards into place and then fasten with screws.
  • Page 19 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo B3a or Now install the upper part of the back wall. Install support board B3a or B3b to hold the upper part of the back wall securely. When this is in place, you can screw the upper part of the back wall to the lower part.
  • Page 20 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo If they start to interfere, they can be removed When the top of the back wall is in place, continue with the construction of the side walls. Use blanks B3a (left) and B3b (right) to build the side walls. Use a rubber mallet to tap the boards into place and then fasten with screws.
  • Page 21 Back Please measure the gap front and back, the dimensions can be different. Back Back Front Front Front...
  • Page 22 Screws S2...7 3x40 ... 4,5x80 Front/2 Front/2 Back/2 Back/2 Divide the measurement by two and transfer the measurements to the last two planks. Connect the dimensions on the plank with a line and cut off these ends. Glue the two freshly cut boards with wood glue and connect them with 6 pieces of 3x40 ...
  • Page 23 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo Insert the last piece and use a rubber mallet to tap the planks together. Screw the loose planks to the walls with screws. Please countersink the screw head!
  • Page 24 M2 Hex bolt The short end must remain Washers M10 under the clamp M1 Tension band (Steel) M5 Tension clamps Hex nut M10 The short end must remain under the clamp ~175mm ~175mm Place the tension bands M1 (Steel band) around the side walls and thread the bands into the eyelet as follows (see sketch above).
  • Page 25 Remove the back wall connection strips Remove the door moldings (2x B7a) in order to install the door later Fixed with 5 screws both Remove the back wall connection strips...
  • Page 26 Inside Outside Screws 3x30 Inside Inside Outside Outside The inner and outer ventilation grilles V2 and adjustable cover V3 are screwed with 3 screws.
  • Page 27 S6.2 NB! use a level Screws 4,2x75 S3.2 Screws 4,5x50 Screws S6.2 Screws S3.2 Install the doors from inside (shown in the picture). Screw the door from the sides with 5 screws from the bottom and from the top with 2 screws. If the door is in place, install the door moldings, top with 2 screws and bottom with 2 screws and the sides with 5 screws.
  • Page 28 Nail 2,5x25 Install the underlay in the center of the roof. The underlay must extend over the front end and back end at least by 40 mm. Use nails to fix the underlay, then use a heat source to make it stick to the boards. When the underlay is in place, their ends must be fixed.
  • Page 29 Back Nail 2,5x25 These pictures are for installing Plano XL cover plates. More or less the same applies to other cover plates. The base sheet of the first row must be installed first. Sheets are self-adhesive, for better adhesion use a heat source. Front Front Back...
  • Page 30 Back Nail 2,5x25 These pictures are for installing Plano XL cover plates. More or less the same applies to other cover plates. The first sheet of the first row starts from the bottom and center of the side wall of the sauna. Sheets are self-adhesive, for better adhesion use a heat source.
  • Page 31 Nail 2,5x25 These pictures are for installing Plano XL cover plates. More or less the same applies to other cover plates. The roof ridge must be placed in the middle, starting from the back end of the sauna or from the front end. Sheets are self-adhesive, for better adhesion use a heat source.
  • Page 32 Screws 4,5x70 S6.1 NB! use a level (black coated) Installation of cover boards at the front end and at the back end of the sauna. The installation of the cover boards is started from the bottom as shown in picture. The upper edge of the first cover board must be at the same height as the floor.
  • Page 33 If the cover boards are in place, those gaps that remain between the roof bitumen sheets and the covering board must be filled with sealant.
  • Page 34 Screw Drill Screws 4,5x80 for Spruce NB! use a level Screws 4,2x75 for Thermo Notice! Drill 4mm hole in the K.. square woods before screwing. Height measurements are measured from a straight surface. Please countersink the screw head! First measure and install K28. The upper edge height of K28 is shown in the picture.
  • Page 35 Screw Drill Screws 4,5x80 for Spruce NB! use a level Screws 4,2x75 for Thermo Notice! Drill 4mm hole in the K10 square wood before screwing. (K28) First install and fix the I1 upper bench to the K55 with two S7 screws . Once the upper bench is attached, K10 must be installed next.
  • Page 36 Screw Drill Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 4mm hole in the K.. square woods before screwing. K45 and K45 and The measurement must be started from the lower edge of the square wood attached under the bench. The square wood and cover board are longer, they must be cut to the correct size.
  • Page 37 Screw Drill Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 4mm hole in the K.. square Screws 4,5x80 for Spruce woods before screwing. Screws 4,2x75 for Thermo Height measurements are measured from a straight surface.
  • Page 38 Screw Drill Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 4mm hole in the K.. square Screws 4,5x80 for Spruce woods before screwing. Screws 4,2x75 for Thermo Install and fix the I4 upper bench to the wall mounts K45 with two S7 screws and K30 with two S5 screws.
  • Page 39 Screw Drill Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 4mm hole in the K.. square woods before screwing. The measurement must be started from the lower edge of the square wood attached under the bench for square wood legs.
  • Page 40 Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Screws S7 Screws S7 The cover board is longer, it must be cut to the correct Attach the D3 cover board piece to K90 square wood with size .
  • Page 41 Screw Drill Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 4mm hole in the K.. square woods before screwing. The measurement must be started from the lower edge of the square wood attached under the bench. The square wood and cover board are longer, they must be cut to the correct size.
  • Page 42 Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Install the bench skirt I6. It must be placed so that there is a small gap between the lower edge and the bench I5. Fasten with four screws.
  • Page 43 NB! use a level Screws 3x40 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo The height of the lower edge of the backrest is shown in the picture. First install the bench backrest I7 and fasten with three screws S5. The height of the lower edge of the backrest is shown in the picture.
  • Page 44 Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Notice! Drill 5mm hole in the I9.2 before Screws 4,5x80 for Spruce screwing. Screws 4,2x75 for Thermo Installation of heater thermal plate I9.2. First install the leg I9.1 of the thermal protection plate I9.2, place it as shown in the pictures.
  • Page 45 DOOR ADJUSTMENT MANUAL 1) Vertical adjustment of the door sash The hinge on the side of the sash has a height adjustment bolt (fig.1), from which is possible to adjust the distance between the hinges. Turning clockwise, the hinges move further apart, and the door sash moves higher.
  • Page 46 3) Adjusting the depth of the door frame The distance of the door sash to the door frame can be adjusted both by the hinges (fig.3) and by the lock (fig.4). The distance between the sash and the frame can be adjusted by the hinges by turning the bolt in Fig.3 –...

  • Page 47: Adjusting The Hinges

    ADJUSTING THE HINGES • Remove plastic from hinges (first picture). To remove plastic, lift it from the places indicated by the red lines; • To regulate hinges you need TORX 30 bit and cordless drill; • Loosen the bolt shown in figure slightly. (DO NOT OPEN COMPLETELY); •...

Table of Contents