1. Manuals
  2. Brands
  3. Heritage Manuals
  4. Plumbing Product
  5. Lux Cube Imperial
  6. Construction manual

Heritage Lux Cube Imperial Construction Manual

Hide thumbs

Advertisement

Table of Contents

Heritage™ Lux Cube Imperial
Exterior construction guide
Read the manual and check the parts for
completeness before assembly!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Lux Cube Imperial and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Heritage Lux Cube Imperial

Summary of Contents for Heritage Lux Cube Imperial

  • Page 1 Heritage™ Lux Cube Imperial Exterior construction guide Read the manual and check the parts for completeness before assembly!
  • Page 2 USER MANUAL OF THE SAUNA 1. It is recommended to install the sauna above ground level to prevent the legs of the sauna from coming into direct contact with the ground. Install a water-resistant material, such as bitumen strips, between the legs of the sauna and the base. 2.

  • Page 3: Warranty

    Maintenance of the sauna 1. The interior surfaces of the sauna, the window frames of the steam and washing room, and the frames of interior doors must be treated with a special substance before initial use to protect them from humidity and dirt and extend the useful life of the sauna. Later, this should be done once or twice a year.

  • Page 4: Front View

    Heritage™ Lux Cube Imperial ~3080 ~3080 1030 1030 2400 2400 Front view Back view Front Back Heritage™ Lux Cube Imperial Length ~2400 mm ~2600 mm ~2344 mm ~2544 mm ~896 mm ~996 mm Scale 1 : 30 (SINGLE) 2.4 and 2.6 Heritage™...

  • Page 5: Detail List

    Heritage™ Lux Cube Imperial B6a1 Round Cube (SINGLE) ~214 mm ~120 mm ~120 mm ~120 mm ~120 mm Length ~2002 mm ~2202 mm ~55 mm ~2344 mm ~2544 mm B2.1 B2.2 B3a1 B3b1 Detail list 1 43 x 43 x...
  • Page 6 Heritage™ Lux Cube Imperial ~60 mm ~60 mm ~85 mm l=~2.4m Length =~9.8m l=~2.5m for RC 2.4 l=~2.7m for RC 2.6 3 x (Black) 2 x (Brown) 10 pcs for RC 2.4 and RC 2.6 16 x 8 pkg for RC 2.4 Detail list 2 and RC 2.6...
  • Page 7 Heritage™ Lux Cube Imperial Name in Nails and screws / Screw size Quantity Area of use (Scale 1:2) manual Screws 4,5x80 for Spruce Mainly for construction inside and outside Screws 4,2x75 for Thermo S6.2 For fixing the door(s) Screws 4,2x75 S6.1...
  • Page 8 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce NB! use a level Screws 4,2x75 for Thermo The base of the sauna must be level! B2.1 B2.1 B2.1 mm=mm mm=mm B2.1 B2.1 Round Cube (SINGLE) Length 896 mm 996 mm Exterior construction...
  • Page 9 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Please countersink the screw head(s)! B2.1 B2.1 mm=mm B2.1 max.45° Exterior construction...
  • Page 10 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Please countersink the screw head(s)! Use a rubber mallet to tap the planks together! Drill 10 mm hole in each plank groove! B3a Left and B3a1 Left and...
  • Page 11 Heritage™ Lux Cube Imperial Cut a hole for the drain pipe (only necessary if there is no hole) ! Add two coats Add two coats of paint of varnish Clean the groove and floor surfaces from ( Remmer HK lasur PINE ) ( INARIJÄRVI )
  • Page 12 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Lift the bottom of the sauna up on one side and install some aids! Clean the bottom surface! Cover the surface with paint (black), let the paint dry!
  • Page 13 Heritage™ Lux Cube Imperial Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo Please countersink the screw head(s)! max. min. B2.2 Assemble and prepare of the front wall! 22 mm 15 mm Use glue between the B4a, B4b and B4c! Screws S5...
  • Page 14 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Add two coats of paint Add two coats of paint Screws 4,5x60 for Spruce ( Remmer HK lasur PINE ) ( Remmer HK lasur PINE ) Screws 4,2x55 for Thermo...
  • Page 15 Heritage™ Lux Cube Imperial Boards Preparation for side wall boards. B3a B3b B3a B3b B3a B3b B3a B3b Add paint ü ü û û û û û û Before doing the processes, clean the sidewall Process 1 ( Teknos black ) boards from wood waste and other dirt! ü...
  • Page 16 Heritage™ Lux Cube Imperial Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo mm=mm Please countersink the screw head(s)! Make sure that the front wall and the lower part of the back wall are centered in relation...
  • Page 17 Heritage™ Lux Cube Imperial Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo Remove the back wall connection strips Screws S5 Please countersink the screw head(s)! Use boards B3a and B3b, that are labeled...
  • Page 18 Heritage™ Lux Cube Imperial Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo If they start to interfere, they can be removed Please countersink the screw head(s)! Use a rubber mallet to tap the planks into place! Please do not screw the screws in on...
  • Page 19 Heritage™ Lux Cube Imperial Measure the gap front and back, the dimensions can be different! Back Divide the measurement by two and transfer the measurements to the last two planks. Connect the dimensions on the plank with a line. Front...
  • Page 20 Heritage™ Lux Cube Imperial Screws S2...7 3x40 ... 4,5x80 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo Please countersink the screw head(s)! Prepare the last plank! Use a rubber mallet to tap the planks in to the cap! Cut along the marked line to cut off these ends.
  • Page 21 Heritage™ Lux Cube Imperial Place the tension bands M1 (Steel band) around the M2 Hex bolt side walls and thread the bands into the eyelet as follows (see sketch above). The short end must remain Washers M10 Hex nuts and bolts must be tightened as long as the under the clamp planks are stationary in all directions.
  • Page 22 Heritage™ Lux Cube Imperial Nail 2,5x25 Install the outer underlay's first and fasten with nails! Install the middle underlay! Use the heat source on the middle underlay, along the long edges for better adhesion! Cut off the ends that extend over...
  • Page 23 Heritage™ Lux Cube Imperial Cover underlay joints with adhesive tape, on top of the sauna! Cover the edge of the underlay, at the front end of the sauna and at the back of the sauna, with adhesive tape! Front and back end, fold the adhesive...
  • Page 24 Heritage™ Lux Cube Imperial Nail 2,5x25 Sheets are self-adhesive, for better adhesion use a heat source! The base row starts from the front, from the second board and with offset! Cut sheets that extend over the edge! Front Back Suitable leftovers can be used!
  • Page 25 Heritage™ Lux Cube Imperial ~326 Nail 2,5x25 Sheets are self-adhesive, for better adhesion use a heat source! The 1.row starts from the bottom and center of the side wall of the sauna. Cut sheets that extend over the edge! Front...
  • Page 26 Heritage™ Lux Cube Imperial Nail 2,5x25 of R4 12pcs for Round Cube 2.4 13pcs for Round Cube 2.6 Sheets are self-adhesive, for better adhesion use a heat source! The roof ridge can be started from the back end of the sauna or from the...
  • Page 27 Heritage™ Lux Cube Imperial Screws 4,5x70 S6.1 NB! use a level (Black coated) Please countersink the screw head(s)! Install the cover boards with 3 screws! Add glue for the 3 lower cover boards! Fill the gaps between the bitumen sheets...
  • Page 28 Heritage™ Lux Cube Imperial Inside Screws 3x30 The inner and outer ventilation grilles V2 and adjustable cover V3 are screwed with 3 screws. Outside Inside (Brown) Outside (Black) Inside Outside (Black) (Black) (Brown) Exterior construction...
  • Page 29 Heritage™ Lux Cube Imperial S6.2 Screws 4,2x75 NB! use a level Insert hole cover P if S3.2 Screws 4,5x50 they are not attached! Please countersink the screw head(s)! Insert hole cover P if they are not attached! Install the door from the inside,...
  • Page 30 Heritage™ Lux Cube Imperial Bench assembly guide Read the manual and check the parts for completeness before assembly!
  • Page 31 Heritage™ Lux Cube Imperial ~3079 3012 2928 ~600 ~600 ~400 ~400 ~600 ~600 ~340 ~340 ~340 ~340 ~400 ~400 Heritage™ Lux Cube Imperial Scale 1 : 30 (SINGLE) 2.6 Bench assembly...

  • Page 32: Detail List

    Heritage™ Lux Cube Imperial Round Cube Round Cube Name in Name in K Square woods 45x45mm Cover boards manual manual 900 mm 900 mm 88x28 mm 550 mm 450 mm 45x28 mm 450 mm 450 mm 88x28 mm 350 mm...
  • Page 33 Heritage™ Lux Cube Imperial Round Cube (SINGLE) Length Back view ~1845 mm ~2045 mm ~1845 mm ~2045 mm ~1845 mm ~2045 mm ~1845 mm ~2045 mm ~1845 mm ~2045 mm Front view ~1817 mm ~2017 mm ~1095 mm ~1295 mm...
  • Page 34 Heritage™ Lux Cube Imperial Screws S5 Screws S2 Screws 3x40 1 . Remove hole cover P if they are attached! Screws 4,5x60 for Spruce 2. Screw the bench Screws 4,2x55 for Thermo backrest 3 . Put the hole cover P...
  • Page 35 Heritage™ Lux Cube Imperial Screws S5 Screws 4,5x60 for Spruce I2a Left Screws 4,2x55 for Thermo (I2b Right) I2a Left Screws 4,5x80 for Spruce (I2b Right) Screws 4,2x75 for Thermo Screws S5 NB! use a level Please countersink the screw head(s)!
  • Page 36 Heritage™ Lux Cube Imperial Screws S7 Screws S7 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo I3a Left Screws 4,5x80 for Spruce (I3b Right) Screws 4,2x75 for Thermo Screws S5 NB! use a level I1 Left I2a Left I2a Left...
  • Page 37 Heritage™ Lux Cube Imperial Screws S5 Screws 4,5x60 for Spruce Screws 4,2x55 for Thermo I3a Left I3a Left (I3b Right) (I3b Right) NB! use a level Please countersink the screw head(s)! The square wood K45 and cover boards D4 and D5 are longer, they must be cut...
  • Page 38 Heritage™ Lux Cube Imperial Screws S5 Screws 4,5x60 for Spruce NB! use a level Screws 4,2x55 for Thermo Screws 4,5x80 for Spruce Screws 4,2x75 for Thermo Please countersink the screw head(s)! First measure and mark the distance for K34! I3a Left...
  • Page 39 Heritage™ Lux Cube Imperial Install the step bench I5! Place the floor mat F1! Bench assembly...
  • Page 40 DOOR ADJUSTMENT MANUAL 1) Vertical adjustment of the door sash The hinge on the side of the sash has a height adjustment bolt (fig.1), from which is possible to adjust the distance between the hinges. Turning clockwise, the hinges move further apart, and the door sash moves higher.
  • Page 41 3) Adjusting the depth of the door frame The distance of the door sash to the door frame can be adjusted both by the hinges (fig.3) and by the lock (fig.4). The distance between the sash and the frame can be adjusted by the hinges by turning the bolt in Fig.3 –...

  • Page 42: Adjusting The Hinges

    ADJUSTING THE HINGES • Remove plastic from hinges (first picture). To remove plastic, lift it from the places indicated by the red lines; • To regulate hinges you need TORX 30 bit and cordless drill; • Loosen the bolt shown in figure slightly. (DO NOT OPEN COMPLETELY); •...

Table of Contents