Table of Contents
Advertisement
Quick Links
Air/water heat pump
ANGHP
GENERA CONTROLLER
374254125.00
11/2024
User manual
«Translated from original instructions»
Manuale d'uso
«Istruzioni originali»
Mode d'emploi
«Traduit des instructions originales»
Benutzungsanleitungen
«Aus der Originalanleitung übersetzt»
Instrucciones de uso
«Traducido de las instrucciones originales»
Instruções de uso
«Traduzido das instruções originais»
EN
IT
FR
DE
ES
PT
Advertisement
Table of Contents
Related Manuals for Argo GENERA ANGHP
Summary of Contents for Argo GENERA ANGHP
- Page 1 User manual «Translated from original instructions» Manuale d’uso «Istruzioni originali» Mode d’emploi «Traduit des instructions originales» Benutzungsanleitungen «Aus der Originalanleitung übersetzt» Instrucciones de uso Air/water heat pump «Traducido de las instrucciones originales» ANGHP Instruções de uso «Traduzido das instruções originais» GENERA CONTROLLER 374254125.00 11/2024...
-
Page 3: Table Of Contents
Contents 1 - Important information ........4 2 - Control module installation . -
Page 4: Important Information
1 - Important information Installation data Product Serial number Heat pump serial number Installation date Installer Serial number must always be given. Certification that the installation is carried out according to instructions in the accompanying installer manual and applicable regulations. Date:_______________________ Signed: _______________________________________ Safety information... -
Page 5: Control Module Installation
2 - Control module installation How to install the control module on the wall • Remove the safety screw located on the bottom left of the module. • Remove the module cover. • Mark the position of the holes to be drilled on the wall with a pencil. •... -
Page 6: Electrical Connection
3 - Electrical connection General NOTE • Electrical installation and wiring must be carried out in Do not start the system before filling up with accordance with national provisions. water. Components in the system could be • Disconnect the control module before insulation testing damaged. -
Page 7: Commissioning And Adjusting
Type Ref. Description Notes Earth Power supply, protective earth Power supply Neutral Power supply, neutral line 220 – 240 V ~ / 1 / 50 Hz Phase Power supply, phase line DHW valve, close Phase line output, activated for DHW valve closing (DHW mode) Phase Phase line, input... -
Page 8: The Control Module
5 - The control module The NGHP Genera module is necessary to control the operation of the air/water heat pump and all accessories connected (boiler, water heater, additional heating, etc.) and create a complete system. This control also has a built-in Wifi system. All settings can be made via the small screen (touch screen) by following the instructions in this manual. - Page 9 Main menu screen Functions Parameters Components General Functions menu: it contains the main functions available on the unit, such as the selection of the operating mode, the definition of the priorities of the latter, the seasonal change and other auxiliary functions. Parameters menu: it allows the setting of the values of the main functions of the unit (heating, cooling, DHW production).
-
Page 10: Technical Settings
Numeric keyboard When it is necessary to enter a numerical value, the following keyboard will be displayed. Cancel Confirm 6 - Technical settings The following settings must be made by the installer in order to operate the heat pump and the system correctly. Login screen with password By pressing the symbol the following screen will appear to allow the technician to set the main functions of the... -
Page 11: Menu "General"
Menu “General” It defines the setting of reference elements such as time and date, language, etc. Enter the “General” menu from the main menu screen. MENU “GENERAL”: ON/OFF unit Settings WI-FI set and profile Factory reset Operation General Emergency Configuration Settings details Menu item Available... - Page 12 Switch-on logic 1: A heat pump turns on as late as possible and turns off as early as possible. This means that all heat pumps that are already switched on must work at full load before the next heat pump switches on. During the check, all the heat pumps therefore work at maximum load, except the last one which turns on.
-
Page 13: Operation Menu
Both the operating mode of the single unit and any alarm status are highlighted on the screen. By clicking on the MASTER unit (the one to which the control module is connected - highlighted compared to the others) you return to the main menu and all the setting screens become available exactly as if the unit were single. If you click on one of the SLAVE units, the available options are shown in the next screen: Unit 4 unit... - Page 14 Parameters: it allows the display of the values of the main parameters of the unit. Text Value T ext. Indicates the external temperature detected by the unit T supply Indicates the supply temperature to the system T return Indicates the return temperature from the system Water flow Indicates the water flow of the unit pump T int.
-
Page 15: Menu "Components"
Menu “Components” It allows the definition and activation of the components provided in the system. Enter the “Components” menu from the main menu screen. MENU “COMPONENTS”: DHW tank: integ. generator integrated resist. integ. P.V. Components DHW tank: touch to change from YES to NO or vice versa (Default: NO) CAUTION If the water tank is not present, the modes that provide for the production of Domestic... -
Page 16: Menu Functions
Integrated resistance The setting screen opens: Component Available Default Explanation range Integ. ER YES/NO It allows an additional electrical resistance, integrated into the system, to be activated starting from the set external temperature following two different operating logics. Ext.T ER interv. -25°C –... - Page 17 Details for setting the various general functions Function Available Default Notes/explanation range Oper. mode Heat Heat If the presence of the DHW tank is not set, the modes with the Cool presence of DHW are NOT available Heat+DHW Cool+DHW Priority Heat-Cool If the presence of the DHW tank is not set, the modes with the presence of DHW are NOT available...
- Page 18 Control module alarm list Type Description Effect Code Status Flow error (1) During the system venting activity, the presen- The unit is put on standby. C001 ce of air in the circuit is highlighted in the pre- The default value is resto- defi ned time red in the selection screen mask (no venting)
- Page 19 Heat pump alarm list Alarm Description May be due to Status E002 10 consecutive aborted defrost • System temperature and/or fl ow too low • Insuffi cient available system volume • Signifi cant wind effect E033 Sensor fault, incoming water sensor in •...
- Page 20 Alarm Description May be due to Status E100 No readback signal from the pump • Disconnected cable • Damaged pump E111 Software fault Defective PCB E113 Over voltage The voltage at the terminal blocks is over a specifi c value E115 Under voltage The voltage at the terminal blocks is under a specifi c...
- Page 21 Details for setting the various system functions Function Available Default Notes/explanation range System type Floor Floor. When the type is changed, all set parameters are reset to the Fan coil corresponding default value. Radiator In particular, the ΔT relating to the different systems are automatically modified, precisely: Floor = 5 °C Fan coil = 5 °C...
- Page 22 Details for setting the various special functions Function Available range Default Notes/explanation Defrost On / Off The function, if set to ON, increases the automatic defrost frequency. frequently Useful for cases where more frequent defrosting is necessary due to extreme external conditions. Ventil.
-
Page 23: Menu "Parameters"
Menu “Parameters” It allows the setting of the values of the main functions of the unit. Enter the “Parameters” menu from the main menu screen. MENU “PARAMETERS”: System parameters DHW parameters Modbus parameters Parameters Details for setting the system parameters If CLIMATE has been selected for the setpoint mode of the system functions: Parameter Available... - Page 24 If FIXED has been selected for the setpoint mode of the system functions: Parameter Available Default Default Default range floor fan coils radiators Heat water T T 20°C - 70°C 40°C 50°C 60°C Cool water T T 7°C - 25°C 18°C 10°C Heat water hysteresis...
-
Page 25: User Functions
7 - User functions Menu “General” It defines the setting of reference elements such as time and date, language, etc. Enter the “General” menu from the main menu screen. MENU “GENERAL”: ON/OFF unit Setting • Date and time • Language •... - Page 26 Via Alfeno Varo, 35 - 25020 Alfianello - BS - Italy Tel. +39 030 7285700 www.argoclima.com...
Need help?
Do you have a question about the GENERA ANGHP and is the answer not in the manual?
Questions and answers