Paul Mitchell NEURO SMOOTH, I0024704 Manual

WHAT'S INSIDE

NEURO® SMOOTH IS CRAFTED FROM INDUSTRIAL-GRADE COMPONENTS UNDER RIGOROUS QUALITY CONTROL.
CREATIVE VISION, POWERED BY CUTTING-EDGE TECHNOLOGY: THAT'S INTELLIGENT STYLING.

ANATOMY OF INTELLIGENT STYLING

INTELLIGENT STYLING TIPS

1. To ensure the smoothest finish and greatest control, smooth only a small amount of hair on each pass, and move the tool slowly and steadily.
2. Run a fine-tooth comb through the hair ahead of the iron to get the hair distributed evenly on the iron's surface.
3. To smooth: begin approximately 1-2 inches from the scalp on the first pass, then move closer to the scalp on the second pass.
4. To flip or wave: close the iron over the hair at the place where you wish the wave to begin and rotate the tool 180 degrees. With firm tension, slowly pull the iron through the hair clockwise all the way through the ends.

For best results, use with Hot Off The Press ® Thermal Protection Hairspray. Treat yourself to award-winning, luxury hair care at an affordable price.
paulmitchell.com
For styling tips scan here

OPERATING INSTRUCTIONS

PRESS MODE BUTTON 1X TO SET TEMPERATURE
Use + and - buttons to select:

• 390°F for fine hair
• 410°F for normal hair
• 430°F for coarse hair
• 450°F for professional use

PRESS MODE BUTTON 2X
TO SET AUTO SHUT-OFF TIME (0-120 minutes)

PRESS MODE BUTTON 3X
TO SELECT FAHRENHEIT (F) OR CELSIUS (C)

PRESS MODE BUTTON 4X
TO RETURN TO MAIN SCREEN

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING.

Any appliance is electrically live, even when the switch is off. When not in use, always unplug the iron to prevent the risk of fire.

To reduce the risk of burns, electrocution, fire or injury to persons and/or personal property:
Use the iron only for the purpose described in this guide to prevent accidents, damage or malfunction. This appliance should never be left unattended when plugged in. Plug the iron into an electrical outlet of AC 120V/60Hz. Avoid multiple cables to a plug or use of an extension cord to prevent starting a fire from overheating. KEEP AWAY FROM WATER to prevent fire, electric shock, damage or malfunction. KEEP AWAY FROM CHILDREN. Do not handle the iron or cord with wet hands as this may cause electric shock. Do not leave the iron in a position where it can fall or be pulled into a tub or sink. Keep the cord away from heated surfaces. DO NOT WRAP THE CORD AROUND THE IRON. Never place or insert objects on iron plates, due to the risk of causing fire, accidents or malfunction. Do not operate where oxygen is being administered to avoid the risk of fire. DO NOT USE WHEN CORD HAS BEEN DAMAGED OR IF PLUG IS LOOSE. DO NOT REPAIR, TAMPER WITH, OR TRY TO RECONSTRUCT the iron, otherwise electric shock, malfunction or accidents may result. When inserting or pulling out the plug, hold the plug firmly to prevent the cord from peeling and to prevent accidents or malfunction. Stop using immediately if you smell an offensive odor. If ignored, it could cause a fire or other accidents. Do not keep the iron in a damp place, such as a bathroom, or it may malfunction. Stop using the iron and remove from the power source when there is an earthquake or thunder. Unplug the iron from the power source when cleaning or wiping to prevent fire or electric shock.

MAINTENANCE
Daily Maintenance: For the safe use of the iron, check the following daily:

• Check the cord and surface of the cord. Never use if any parts are cracked, split, torn or damaged.
• Check the plug and never use if it is cracked, split or damaged.
• Check the plug pins and never use if transformed or damaged.
• Check the controller and do not use if cracked, split, broken or damaged.
• When not in use, clean and dry the entire iron and store in a cool, dry place. When ready to use, follow the directions for daily maintenance.

Daily Cleaning: To keep plates clean, unplug the iron from the power source, and once the iron is cool, wipe down plates after each use with a hot, damp towel.

Do not wipe the iron with thinner, benzene, gasoline, lamp oil, and other solvents or chemicals, as that may cause accidents or malfunction and may damage the iron and void the warranty.

Defects and Malfunction:

• Read all contents of the warranty completely and carefully before contacting the salon, the distributor, or our Paul Mitchell^® Pro Tools™ Warranty Center.
• John Paul Mitchell Systems^® is not responsible for damage caused by misuse or due to operator accidents, such as dropping the appliance on the floor.

OPERATING INSTRUCTIONS
The iron has reached your selected temperature when the display screen reaches the desired temperature. You will hear a "beep" when the iron is ready to use. Once you have finished styling, turn off and unplug the iron. This iron has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit securely, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

GENERAL SPECIFICATIONS
Model: NS12NA
Rated Voltage: 120V AC
Frequency (Hz): 60Hz
Rated Wattage: 45 w
Length of A.C. Cord: 9 ft. / 2,7 m
Weight: Net Wt. 13.4 Oz. / 380 g