Advertisement
Product | Name | Electric Scooter |
Model | A10 | |
Dimensions | Vehicle: L × W × H (in) | 45×17.5×48 |
After Folding: L × W × H (in) | 45×17.5×20.3 | |
Net Weight | Vehicle Net Weight (lb) | 38.0 |
Rider | Max. Load (lb) | 220 |
Age (years) | 12+ | |
Height (in) | 4.72~7.87 | |
Assembled Electric Scooter | Max. Speed (mph) | 15 |
General Range (mile) | Approx. 28 | |
Max. Climbing Angle (%) | Approx. 15 | |
Suitable Surfaces | Cement or asphalt road, with benches of less than 1 cm or crevices narrower than 3 cm | |
Operating Temperature (°C) | -10 to 45 | |
Charging temperature range(°C) | 0 to 45 | |
Storage Temperature (°C) | -20 to 50 | |
IP Rating | IPX5 | |
Charging Time (h) | About 6 | |
Battery Pack | Model | C1387A3 |
Nominal Voltage (VDC) | 36.5 | |
Max. Charge Voltage (VDC) | 42 | |
Rated Energy (Wh) | 365 | |
Rated Capacity (Ah) | 10 | |
Normal Charging Temperature Range (°C) | 0 to 45 | |
Intelligent Battery Management System | Over-heating, short circuit, over-current, over-discharge, and over-charge protection | |
Wheel Motor | Rated Power (W) | 400 |
Battery Charger | Model | FY-4201700/GC72-420170-D |
Output Power (W) | 71.4 | |
Input Voltage (VAC) | 100-240 | |
Max. Output Voltage (VDC) | 42 | |
Rated Output (VDC; A) | 42; 1.7 | |
Tire | Front & Back Tires | Pneumatic tire, Ø 10 × 2.125 straight valve, with the materials of natural rubber |
Attention:
Turn off the scooter, press the red safety lock, and release the folding handle; fold the front tube clamp, align the folding hook and put it into the hook fixing buckle; lift the front tube and confirm whether it is fastened firmly.
Remove the folding hook from the hook fixing buckle, straighten the front tube, close the folding handle until there is a"click"sound; flip the folding handle and confirm whether it is locked.
Scan QR code with your mobile phone to download and install the APP.
If the APP has been installed on your mobile phone, make sure that the APP is the latest.
Zero Start/Non-zero Start Mode
(Recommended):
Maintaining the scooter regularly can help keep the scooter neat and in good condition, avoid safety hazards, minimize breakdowns, slow down the deterioration of the scooter, and extend the scooter's service life.
If there are stains on the surface of the scooter, use a soft cloth and dip in a small amount of water to wipe; lf there are stains that are difficult to clean, smear them with toothpaste and brush them repeatedly, then clean them with a damp cloth. lf the plastic parts of the body are scratched, use sandpaper or other abrasive materials to polish them.
Tips:
Do not use alcohol, gasoline, kerosene or other corrosive and volatile chemical solvents to clean, otherwise it will seriously damage the appearance and internal structure of the body. Do not use pressurized water to spray and wash.
Ensure that the scooter is off and the charging port rubber cover is tightly fastened during cleaning, otherwise electric shock or serious failure may occur due to internal water flow. When not in use, store in a dry and cool place indoors. Avoid outdoor storage for a long time. Long-term sun exposure, overheating and cold outdoor environment will accelerate the appearance and tire aging of the scooter, and reduce the service life of the scooter and battery pack.
The product uses puncture-proof tubeless tires, please check the tire pressure carefully before riding, and ensure the tire pressure is 4550 psi. When the tire height sinks 20%-30%, it is time to inflate. The recommended tire pressure is 45-50 psi after inflation, and the tire should be inflated at least once every 2-3 months. Regular inflation and cleaning of tire surface debris can prolong the service life of the tire.
Code | Description of Fault Content | Solution | Corresponding Parts |
00 | Undervoltage, low battery | Please charge in time. | Battery |
01 | Overvoltage, too high battery | Needs to unplug the charger. | Battery |
02 | Controller Fault | Controller needs to be replaced. | Controller |
03 | MOS Tube Fault | After 15 minutes of shutdown, restart to confirm whether the fault is resolved; if not, the controller needs to be replaced. | Controller |
04 | Hardware Communication Fault | Check the connection line between the controller and the display, if the connection is nommal, but the fault is not resolved, please call the manufacturer. | Controller/ Display |
05 | Hall Fault | Check the Hall wire between the controller and the motor. lf the connection is nommal. but the fault is not resolved, the motor needs to be replaced. | Motor |
06 | Accelerator Fault | Check the accelerator shift connection cable, if the connection is nommal, whether the fault is resolved; if not, replace the shift. | Accelerator |
07 | Brake Lever Fault | Check the brake lever connection line, if the connection is normal, whether the fault is resolved; if not, the brake lever needsto be replaced. | Brake Lever |
08 | OCP Protection | Shut down for 5 minutes, then restart to confirm whether the fault is resolved, if not, replace the controller. | Controller |
09 | Motor Fault | Shut down for 5 minutes, then restart to confirm whether the fault is resolved, if not, replace the motor. | Motor |
10 | Controller and battery connect error | Check the connect communication cable between controller with battery | Controller and battery |
(Recommended):
Maintaining the scooter regularly can help keep the scooter neat and in good condition, avoid safety hazards, minimize breakdowns, slow down the deterioration of the scooter, and extend the scooter's service life.
Item | Service Object | Actions | Every month | Every 3 months | Every 500km/6 months | Every 1000 km/1 year | Every 2000 km/2 years |
Tires | Tire Pressure | Inflate the tire until its pressure reaches 45–50 psi. | √ | √ | √ | √ | |
Tire Tread Wear | Check whether the tire is cracked, deformed, worn, etc. | √ | √ | √ | |||
Screws | Handlebar Assembly Screws | Tighten the screw that connects the handlebar assembly with the stem assembly (with the recommended torque of 3.5 ± 0.2 N·m). | √ | √ | √ | √ | |
Tighten the accelerator screw (with the recommended torque of 1.8± 0.1 N·m). | √ | √ | |||||
Tighten the brake lever screw (with the recommended torque of 3.5 ± 0.2 N·m). | √ | √ | |||||
Functions | Steering | Turn the handlebar 60° to the left and right to make sure the turning angle is correct and the steering is free from resistance and stagnation. | √ | √ | |||
Important Components | Battery Assembly | Fully charge the scooter before leaving it unused for a long time, and turn it on to charge every 60 days. | √ |
27 Distributed by Phantom E-Moto Inc.
Address: 15830 El Prado Unit E Chino, CA 91708
Contact us via email info@phantomgogo.com or call us at 866-5708755 if you need replacement parts, or have any questions.
We will reply within 24 hours.
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the A10 and is the answer not in the manual?
Questions and answers