Related Manuals for TOLSEN TOOLS FORCE XPRESS 79712
Summary of Contents for TOLSEN TOOLS FORCE XPRESS 79712
- Page 1 79712 ROTARY HAMMER INSTRUCTION MANUAL 7A 800W 120V~60Hz SAVE THIS MANUAL ! You will need this manual for safety instructions, operating procedures and warranty. Put it and the original sales receipt in a safe dry place for future reference.
-
Page 2: Important Safety Information
SAFETY IMPORTANT SAFETY INFORMATION General Power Tool Safety Warnings WARNING: Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term ”power tool“ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. - Page 3 SAFETY turning the power tool on. A wrench or a key before making any adjustments, changing le attached to a rotating part of the power tool accessories, or storing power tools. Such may result in personal injury. preventive safety measures reduce the risk of 15.
- Page 4 • Properly These carry important safety information. If maintain and inspect to avoid electrical shock. unreadable or missing, contact tolsen Tools for a • Any power cord must be properly grounded. replacement. Ground Fault Circuit Interrupter (GFCI) should 7.
-
Page 5: Safety And Specifications
SAFETY AND SPECIFICATIONS Vibration Safety This tool vibrates during use. Repeated or medical advice as soon as possible. long-term exposure to vibration may cause 2. Do not smoke during use. Nicotine reduces the temporary or permanent physical injury, blood supply to the hands and fingers, particularly to the hands, arms and shoulders. -
Page 6: Before Use
SYMBOLOGY AND SETUP Note: Symbology Some of the following symbols may be used on your No load speed tool. Please study them and learn their meaning. revolutions or reciprocations Proper interpretation of these symbols will allow you ./min or minˉ¹ per minute to operate the tool better and safer. - Page 7 SETUP Functions Replacement drill chuck On/Off switch Operational mode selection switch Unlocking button Auxiliary handle ACCESSORIES & CARTON CONTENTS DESCRIPTION Rotaryhammer Use only accessories recommended for this Chisels electric hammer chisel. Follow instructions Drill Bits that accompany accessories. Use of improper Auxiliary Handle accessories may cause injury to the operator Depth Gauge...
- Page 8 SETUP OPERATING INSTRUCTIONS Always make sure the power tool is isolated from the power supply before fitting any attachment Put the bit into the hex housing Handle (Fig3) (Fig1) Put the bit into the hex housing and clamp the bit Always make sure the fixed handle is secure by turning the stop lever half a turn anti clockwise.
-
Page 9: Maintenance And Servicing
MAINTENANCE AND SERVICING MAINTENANCE AND SERVICING This electric hammer chisel does not have reverse direction, so always take care not to force the chisel in case the chisel bit gets stuck. Always make sure you keep the chisel going in and out to remove debris. - Page 10 MAINTENANCE AND SERVICING Hammer chisel prior to operation 1. Power source 3. Power switch Ensure that the power source to be utilized Ensure that the power switch is in the off conforms to the power requirements specified position before any work is carried out on the on the product nameplate.
-
Page 11: Maintenance And Inspection
MAINTENANCE AND SERVICING MAINTENANCE Maintenance and inspection 1. Inspecting the tool 4. Inspecting the carbon brushes. When using dull tool bits this can cause motor The motor employs carbon brushes that are malfunction and degraded efficiency. Always consumable parts; since an excessively worn replace dull bits with new ones without delay carbon brush could result in motor trouble, when abrasion is noted. -
Page 12: Troubleshooting
MAINTENANCE AND SERVICING Troubleshooting Problem Possible Causes Likely Solutions Tool will not start. 1. Cord not connected. 1. Check that cord is plugged in. 2. No power at outlet. 2. Check power at outlet. If outlet is 3. Tool’s thermal reset breaker unpowered, turn off... - Page 13 SUZHOU TOLSEN TOOLS CO.,LTD. www.tolsentools.com TOLSEN is a trademark or registered trademark of TOLSEN TOOLS. All rights reserved. SCAN TO VISIT TolsenWorld MADE IN CHINA PRODUCT LINK...
Need help?
Do you have a question about the FORCE XPRESS 79712 and is the answer not in the manual?
Questions and answers