Welcome to Electrolux! Thank you for choosing our appliance. Get usage advice, brochures, trouble shooter, service and repair information: www.electrolux.com/support Subject to change without notice. CONTENTS 1. SAFETY INFORMATION................2 2. SAFETY INSTRUCTIONS................4 3. INSTALLATION....................6 4. PRODUCT DESCRIPTION................9 5.
• Children should be supervised to ensure that they do not play with the appliance. • Keep all packaging away from children and dispose of it appropriately. • WARNING: The appliance and its accessible parts become hot during use. Keep children and pets away from the appliance when in use and when cooling down.
• Metallic objects such as knives, forks, spoons and lids should not be placed on the hob surface since they can get hot. • Do not use the appliance before installing it in the built-in structure. • Do not use a steam cleaner to clean the appliance. •...
– Do not store any small pieces or • If the mains socket is loose, do not sheets of paper that could be pulled in, connect the mains plug. as they can damage the cooling fans • Do not pull the mains cable to disconnect or impair the cooling system.
• Switch off the appliance and let it cool WARNING! down before cleaning. • Do not use water spray and steam to Risk of fire and explosion. clean the appliance. • Fats and oil when heated can release • Clean the appliance with a moist soft flammable vapours.
Page 7
• To replace the damaged mains cable, use One-phase connection the cable type: H05V2V2-F which 1. Remove the cable end sleeve from black, withstands a temperature of 90 °C or brown and blue wires. higher. A single wire must have a minimal 2.
Page 8
How to install your Electrolux Induction Hob - Worktop installation Find the video tutorial "How to install your Electrolux induction hob flush installation" by typing out the full name indicated in the graphic below. ENGLISH...
How to install your Electrolux induction hob flush installation 4. PRODUCT DESCRIPTION 4.1 Cooking surface layout Induction cooking zone Control panel 4.2 Control panel layout Use the sensor fields to operate the appliance. The displays, indicators and sounds tell which functions operate.
Sensor Function Comment field Bridge To activate and deactivate the function. Heat setting display To show the heat setting. Timer indicators of cooking To show for which zone you set the time. zones Timer display To show the time in minutes. Hob²Hood To activate and deactivate the manual mode of the function.
5.1 Power limitation Power levels Refer to “Technical data” chapter. Power limitation defines how much power is used by the hob in total, within the limits of CAUTION! the house installation fuses. Make sure that the selected power fits The hob is set to its highest possible power the house installation fuses.
6.4 OptiHeat Control (3 step You can cook with large cookware placed on Residual heat indicator) two cooking zones at the same time. The cookware must cover the centres of both zones but not go beyond the area marking. If WARNING! the cookware is located between the two centres, Bridge function will not be activated.
Page 13
setting in the beginning and then continues to To change the time: touch to set the operate at the desired heat setting. cooking zone. Touch To deactivate the function: touch to set To activate the function the cooking zone the cooking zone and then touch .
To override the function for only one cooking time: activate the hob with The function has no effect on the comes on. Touch for 4 seconds. Set the operation of the cooking zones. heat setting in 10 seconds. You can operate the hob.
Page 15
selected heat setting and the reduced heat Automatic modes setting. • Wait until the display stops flashing or Automat‐ Boiling 1) Frying 2) reduce the heat setting of the cooking ic light zone selected last. The cooking zones will continue operating with the reduced heat setting.
Operating the fan speed manually Activating the light You can also operate the function manually. You can set the hob to activate the light automatically whenever you activate the hob. To do that press when the hob is active. To do so set the automatic mode to H1 – H6. This deactivates automatic operation of the function and allows you to change the fan speed manually.
panel or accidentally activate hob • clicking: electric switching occurs. functions. • hissing, buzzing: the fan operates. • rhythmic sound: cookware is detected. 7.3 Öko Timer (Eco Timer) Refer to "Technical data". To save energy, the heater of the cooking 7.2 Noises during operation zone deactivates before the count down timer sounds.
• Do not interrupt the signal between the work with this function refer to our consumer hob and the hood (e.g. with the hand, a website. The Electrolux cooker hoods that cookware handle or a tall pot). See the work with this function must have the symbol picture.
at an acute angle and move the blade on WARNING! the surface. Do not use knives or any other sharp, • Remove when the hob is sufficiently metal tools to clean the glass surface. cool: limescale rings, water rings, fat stains, shiny metallic discoloration.
Page 20
Problem Possible cause Remedy Hob²Hood does not work. You covered the control panel. Remove the object from the control panel. You use a very tall pot which blocks Use a smaller pot, change the cooking the signal. zone or operate the hood manually. Automatic Heat Up does not op‐...
Energy consumption of the hob (EC electric hob) 181.2 Wh/kg IEC / EN 60350-2 - Household electric • When you heat up water, use only the cooking appliances - Part 2: Hobs - Methods amount you need. for measuring performance. •...
Need help?
Do you have a question about the EIV634I and is the answer not in the manual?
Questions and answers