Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for D-Link DPN-BE7212GR
Summary of Contents for D-Link DPN-BE7212GR
- Page 1 DPN-BE7212GR User Manual REV 1.12 BE7200 WIFI7 Router Feb 2025 - 1 -...
-
Page 2: Table Of Contents
Contents 1.1 Login Preparation ..........................- 3 - 1.2 Login Steps ............................- 3 - 2.1 Preparation before configuration ....................... - 5 - 2.2 Routing Mode-DHCP ......................... - 5 - 2.3 Routing Mode-PPPoE ........................- 7 - 2.4 Routing Mode-Static IP ........................- 8 - 2.5 Bridge Mode ............................ -
Page 3: Login Web
Login Web 1.1 Login Preparation When logging in for the first time, it is necessary to confirm the following points: 1. The router has been powered on and started normally, and the LAN port or WIFI is connected to the terminal device. 2. - Page 4 3.If you forget your login password, press and hold the reset button on the back of the router for 5-8 seconds to reset it, and then proceed with the configuration in the previous step. - 4 -...
-
Page 5: Internet Access Configuration
Internet Access Configuration 2.1 Preparation before configuration Connect the external network cable to the WAN port of the router. 2.2 Routing Mode-DHCP The current method is the default internet access method and configuration method of the router, as shown in the following figure. Click “save/apply”... - Page 6 If you need to configure custom DNS, select “Static” to configure it. - 6 -...
-
Page 7: Routing Mode-Pppoe
2.3 Routing Mode-PPPOE Select“PPPoE”for Internet Type, and fill in your username and password information. Click“save/apply”to save and activate. - 7 -... -
Page 8: Routing Mode-Static Ip
2.4 Routing Mode-Static IP Before configuring static IP in routing mode, confirm the IP and subnet mask information of the upstream gateway device. Then, based on the information obtained, fill in the following webpage and click “save/apply”to save and make it effective. Note: In static IP mode, DNS needs to be configured. -
Page 9: Bridge Mode
2.5 Bridge Mode In bridge mode, the router is equivalent to a bridge, and the terminal device under it obtains the IP address of the upper level gateway through the current router and accepts the management of the upper level gateway,please follow the steps below to operate. - Page 10 - 10 -...
-
Page 11: Wireless Basic Configuration
Wireless Configuration 3.1 Wireless basic configuration Users can configure Basic information of WIFI 2.4G on this page, including Bandwidth,WiFi Mode and other information. Users can configure SSID information of WIFI 2.4G on this page, including SSID name,Authentication mode,WiFi password,WPS settings and other information. - Page 12 Users can configure Basic information of WIFI 5G on this page, including Bandwidth,WiFi Mode and other information. Users can configure SSID information of WIFI 5G on this page, including SSID name,Authentication mode,WiFi password,WPS settings and other information. - 12 -...
-
Page 13: Wireless Guest Network Configuration
3.2 Wireless Guest Network Configuration Users can configure basic information of WIFI visitors on this page, including SSID,key,Security and other information. Guest WiFi is not enabled by default.If you need to use it,check the enable box then click the “Apply” button. - 13 -... -
Page 14: Lan Configuration
LAN Configuration 4.1 Basic configuration of IPv4 LAN Each device in the network has a unique IP address, which can be used to log in to the management interface and operate the router. The current page can modify this IPv4 address and also modify the IPv4 address range and other information obtained by the hanging terminal device. -
Page 15: System Configuration
System Configuration 5.1 Reboot operation Click “System” → “System” → “Reboot” to enter the reboot configuration page. Click “ Reboot” to pop up a reboot confirmation box. Click “OK” to perform the router reboot operation. - 15 -... -
Page 16: Reset Operation
5.2 Reset operation Click “System” → “Restore Default” to enter the reset configuration page. Click “Reset” to pop up a restore confirmation box. Click “OK” to perform the router reset operation. - 16 -... -
Page 17: Local Update Operation
5.3 Local update operation Click “System” → “System” → “Update Software” to enter the update page. Click “Choose File” button to choose software. After selecting,the name of the software to be upgraded will be displayed here. - 17 -... - Page 18 Click “Update Software” button to start upgrade. The router will be upgraded and restarted, please wait for two minutes. - 18 -...
-
Page 19: Online Update Operation
5.4 Online update operation Click “System” → “System” → “FOTA” to enter the online update page. Confirm that the FOTA function is enabled and set the time period for detecting upgrade,click the “save/apply” button to save the configuration. The router will check for new version during each set time period,if a new version is found it will automatically upgrade. -
Page 20: Mesh Network By Webpa
Easymesh Configuration Preparations before networking: Two DPN-BE7212GR routers. 6.1 Mesh network by webpage Click “Basic” → “WLAN” → “Easymesh” to enter the Eashmesh configuration page. If one of the routers is connected to the upstream, it will be automatically recognized as a controller. - Page 21 Use another router as the agent role.If it is also connected to the upstream,you need to manually select the role as the agent and then click “save/apply” button. Click the “Trigger WiFi on boarding” button on the Easymesh page of the agent and controller at the same time or click the two buttons at the same time as possible.
- Page 22 After waiting for about 30 seconds,check the networking status on the Easymesh Topology page. If the mesh networking is successful,relevant role information can be viewed on the topology map. - 22 -...
-
Page 23: Mesh Network By Mesh Button
6.2 Mesh network by MESH button Use one router which connected to the upstream as the Controller role,and another router which not connected to the upstream as the Agent role(or both connected to the upstream but manually set one of them as the Agent role on the webpage).Press the MESH button on both routers simultaneously for about 10 seconds. -
Page 24: Mesh Network By Wire
After waiting for about 30 seconds, login to the web account of the Controller role and check if the networking is successful on the Easymesh Topology page. 6.3 Mesh network by wired Use one router which connected to the upstream as the Controller role,and another router which not connected to the upstream as the Agent role(or both connected to the upstream but manually set one of them as the Agent role on the webpage).Connect any LAN port of two... - Page 25 After waiting for about 30 seconds, login to the web account of the Controller role and check if the networking is successful on the Easymesh Topology page. - 25 -...
-
Page 26: Vpn Configuration
VPN Configuration 7.1 VPN settings Click “Advance” → “NAT” → “VPN manager” to enter the VPN configuration page. Check the “Enable”option box,choose the “VPN protocl”,fill in “Service Address”,“User name”and“Password”,click “Save/Apply” button. - 26 -... - Page 27 After submitting the configuration,you can view the VPN status information on the current page. - 27 -...
Need help?
Do you have a question about the DPN-BE7212GR and is the answer not in the manual?
Questions and answers