Download
Share
Print this page
Marantz UD5005 Service Manual
  1. Manuals
  2. Brands
  3. Marantz Manuals
  4. Blu-ray Player
  5. UD5005
  6. Service manual
Marantz UD5005 Service Manual

Marantz UD5005 Service Manual

Hide thumbs Also See for UD5005:

Advertisement

Quick Links

Download this manual
Service
Manual
• For purposes of improvement, specifications and design are subject to change without notice.
• Please use this service manual with referring to the operating instructions without fail.
• Some illustrations using in this service manual are slightly different from the actual set.
S0533-0V08DM/DG1209
UD5005
Copyright 2012 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
UD5005 /
N1SG/N1B/U1B/K1B
SUPER AUDIO CD/
BLU-RAY DISC PLAYER
S1SG/S1B/R1B
Ver. 8
Please refer to the
MODIFICATION NOTICE.

Advertisement

loading
Need help?

Need help?

Do you have a question about the UD5005 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Marantz UD5005

Summary of Contents for Marantz UD5005

  • Page 1 Service UD5005 / N1SG/N1B/U1B/K1B S1SG/S1B/R1B Manual SUPER AUDIO CD/ BLU-RAY DISC PLAYER • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set.
  • Page 2 Parts for your equipment are generally available to our National Marantz Subsidiary or Agent. ORDERING PARTS : Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specified.
  • Page 3 SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. LEAKAGE CURRENT CHECK Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
  • Page 4 NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
  • Page 5 WARNING AND LASER SAFETY INSTRUCTIONS WARNING WAARSCHUWING Alle IC’s en vele andere halfgeleiders zijn gevoelig All ICs and many other semi-conductors are voor elektrostatische ontladingen (ESD). susceptible to electrostatic discharges (ESD). Onzorgvuldig behandelen tijdens reparatie kan de Careless handling during repair can reduce life levensduur drastisch doen verminderen.
  • Page 6 INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
  • Page 7 TECHNICAL SPECIFICATIONS d n Audio performance Analog audio output : Output level : 2 Vrms (10 kΩ) Signal format : NTSC, PAL 2 channels output terminal : Pin-jack, 1 set Applicable discs /memory device : Audio output characteristics : (1) BD-Video disc : (1) Frequency response 12 cm, 1 side, 1 layer;...
  • Page 8 Refer to "MEASURING METHOD AND WAVEFORMS". When you repair the BD MECHA UNIT, you can use the following JIG. Please order to marantz Official Service Distributor in your region if necessary. Do not supply it : 2-Dimensional Bar Code Reader (DS6708 made by Symbol Co. etc.)
  • Page 9 DISASSEMBLY d • Disassemble in order of the arrow in the following figure. • In the case of the re-assembling, assemble it in order of the reverse of the following flow. • In the case of the re-assembling, observe "attention of assembling". • I f wire bundles are untied or moved to perform adjustment or replace parts etc., be sure to rearrange them neatly as they were originally bundled or placed afterward. Otherwise, incorrect arrangement can be a cause of noise generation. TOP COVER FRONT PANEL ASSY REMOTE PWB UNIT Refer to "DISASSEMBLY Refer to "DISASSEMBLY Refer to "DISASSEMBLY 1. FRONT PANEL ASSY" 3. REMOTE PWB UNIT" 4. FAN" and "EXPLODED VIEW" and "EXPLODED VIEW"...
  • Page 10 1. FRONT PANEL ASSY Proceeding : TOP COVER FRONT PANEL ASSY → (1) Detach the LOADER PANEL. Shooting direction: B (2) Disconnect the FFC cable. FFC cable (3) Lift up to unhook the claw and move in the direction of arrow to gradually pull out the assembly. Shooting direction: D Shooting direction: C View from the bottom Please refer to "EXPLODED VIEW" for the disassembly method of each P.W.B included in FRONT PANEL ASSY.
  • Page 11 2. BD MAIN UNIT ASSY Proceeding : TOP COVER FRONT PANEL ASSY BD MAIN UNIT ASSY → → (1) Disconnect the connector wires and FFC cables, then remove the screws. FFC cable BD MAIN UNIT ASSY POWER PWB UNIT FFC cable BACK PANEL ASSY (2) Remove the screws. Shooting direction: A (3) Remove the screw. View from the bottom...
  • Page 12 (4 ) Remove the screws. BD MAIN UNIT ASSY POWER PWB UNIT BACK PANEL ASSY Please refer to "EXPLODED VIEW" for the disassembly method of MAIN P.W.B included in BD MAIN UNIT 3. REMOTE PWB UNIT Proceeding : TOP COVER REMOTE PWB UNIT → Please refer to "EXPLODED VIEW" for the disassembly method of REMOTE PWB UNIT. 4. FAN Proceeding : TOP COVER → Please refer to "EXPLODED VIEW" for the disassembly method of FAN. 5. POWER PWB UNIT Proceeding : TOP COVER POWER PWB UNIT →...
  • Page 13 REMOVING DISCS (1) Remove the Top Cover. (2) Open the CD tray by turning the Drive gear counterclockwise. Drive gear Shooting direction: D...
  • Page 14 DIAGNOSTICS OF OPTICAL PICKUP g Make failure diagnostics of the Optical Pickup as follows. q If the laser drive current (Iop) becomes more than BD : ± 6 [mA], DVD or CD : ±12 [mA] of the initial value, the Optical Pickup should be replaced.
  • Page 15 1. Iop checked Method Select the laser ON/OFF(CD/DVD/BD)mode of the test mode, and check the IOP value of CD laser, DVD laser or BD laser. (Refer to "6. Test mode") FL Display (The display part of 13 digits) L a s e r O n O f f Laser current check Press the 8 or 9 button to display the laser current value, and then select [X].
  • Page 16 1. How to Replace the BD MAIN UNIT (including the MAIN PWB UNIT) (1) Refer to the removal procedure, and remove and replace the BD MAIN UNIT(UD5005). (see "DISASSEMBLY") (2) Follow the firmware update procedure, and update the firmware to the latest version.
  • Page 17 [Connection] (1) Connect the PC and bar code reader. (2) Connect the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig to the MAIN PWB UNIT (CON601) of the set. (3) Connect the USB side of the USB - 232C (TTL) conversion jig to the PC. PC (USB)へ...
  • Page 18 (5) On the screen below, select "ComPort XX". Select the USB - 232C (TTL) conversion jig port. (6) Check "Directly".
  • Page 19 Click the left edge of the "Bar Code" window, and the cursor begins to flash. Click (8) Place the bar code reader over the bar code attached to the replacement BD MECHA UNIT ASSY. When the reader has finished reading the barcode, the read data is displayed. b If the 2-dimensional barcode data has already been read by the 2-dimensional barcode reader, and the converted data obtained, copy the data from the data file, and paste it into this section.
  • Page 20 (9) Click Write(F2). (10) When “Pass” changes to green, writing to the Flash ROM of the MAIN PWB UNIT is complete. (11) Switch off the set unit power, and remove the 232C (TTL) side 4P PH connector of the USB - 232C (TTL) conversion jig from the MAIN PWB UNIT (CON601).
  • Page 21 2.4. Replace the BD MECHA UNIT ASSY (1) Remove the old BD MAIN UNIT from the set unit (see "DISASSEMBLY"). (2) Remove the MECHA COVER. DRIVE MECHA UNIT TOP COVER (3) Disconnect the connector wire and FFC cable. MAIN PWB UNIT FFC cable HA700 (4) Move the optical pickup to the outer circumference, remove the FFC Cable, and remove the screws.
  • Page 22 (5) Attach the BD MECHA UNIT ASSY for replacement to the set unit. (When assembling the unit, perform the steps in reverse order.) (6) Check that the 45P-FFC, 9P-FFC and 5P-PH connector cords have been connected. 2.4. Configure the settings of the set that contains the new BD MECHA UNIT (1) Check the laser amperage (see laser on/off mode in the test mode (page 26)).
  • Page 23 SERVICE MODE 1. Initial setting mode 1.1. preparation (1) E quipment used: None (2) U nit setting: No spec other than the following procedure. 1.2. procedure b I nitialize the BD player when µcom, peripheral parts of µcom, or MAIN P.W.B. unit has been replaced in servicing. b A ll user setting will be lost and its factory setting will be restored when this initialization is made. Be sure to memorize your setting for restoring again after the initialization. (1) T urn on this model's power. "NO DISC" is displayed on the fluorescent tube. (2) P ress the this model's 2 and SOUND MODE buttons simultaneously. "INITIALIZING" is displayed on the fluorescent tube. (3) T he display on the fluorescent tube switches to "INITIALIZED", the "NO DISC" display reappears and initialization is completed. 2. Firmware version check mode 2.1.
  • Page 24 (1) Pressing the PURE DIRECT and 3 buttons for simultaneously. (2) “Lock-On” is displayed on the FL tube, and operations with the remote control and the REMOTE CONTROL input terminal on the back of the UD5005 are disabled. [Cancel] (1) Pressing the PURE DIRECT and 3 buttons for simultaneously.
  • Page 25 6. Test mode d h 6.1. Entering the test mode The test mode is entered by pressing the 5 and 3 buttons simultaneously, plug the AC cord into a power outlet. When the test mode is set, the " 1 " and " 3 " indicators light. FL tube display when test mode entered FL Display (The display part of 13 digits) When the test mode is set, the choice screen of the mode appears on the monitor.
  • Page 26 6.3. About each mode ・ With the mode selected, press the 1 button to set that mode. (1) Laser on/off (CD/DVD/BD) mode Press the 8 or 9 button to select [X] and press the 1 button to set it. Laser on/off control is executed and the laser current is displayed. FL Display (The display part of 13 digits) (X=1 : CD laser mode, 2 : DVD laser mode, 3 : BD(SL) laser mode) (mmmm[mA] : Stored data, nnnn[mA] : Current value) b W hen the current value is more that BD: ±6[mA], DVD or CD: ± 12[mA] of saved data, it becomes the pickup transducer's target. In this case, replace the mechanism unit. When the 2 button is pressed, the layer above the current layer is displayed. See "6.4 Stopping the mode". (2) Error rate measurement mode Press the 8 or 9 button to select [YY] . Refer to [Table 1 - Error rate details]. FL Display (The display part of 13 digits) (YY : measurement mode, F : Address and error rate (When not set, "F" is displayed.) Press the 1 button to begin error rate measurement. The address and error rate are displayed. For a description of the displayed measurement results, see "Table 1: Error rate details".
  • Page 27 (3) Accumulated laser on time display mode Press the 8 or 9 button to select [Y] and press the 1 button to set it. The accumulated laser on time is displayed. FL Display (The display part of 13 digits) (Y=1 : CD, 2 : DVD , 3 : BD, mmmmmm : Time(Fractions of hours are counted up one hour on the display.) When the 2 button is pressed, the layer above the current layer is displayed. See "6.4 Stopping the mode". ---To clear the accumulated laser on time--- Press the 1 button while the accumulated laser on time is displayed ("TC1, "TC2", "TC3" ) until "TC4 ＊ clear??" appears at the display. FL Display (The display part of 13 digits) If the 1 button is pressed, the accumulated laser on time of CD, DVD and BD is cleared. FL Display (The display part of 13 digits) When "TC1", "TC2" or "TC3" is selected with the 8 or 9 button, "mmmmmm" is displayed as "0" so you can check. (4) Picking up No. display mode Press the 8 or 9 button to switch to the pickup number display. The pickup number is a 15-digit number, so it is displayed in two sections.
  • Page 28 6.4. Stopping the mode When the 2 button is pressed, the layer above the current layer is displayed. The relationship between the different modes and the display of the different layers is shown on the table below. Mode 1 layer 2 layer 3 layer Laser on/off (CD/DVD/BD) mode T2 LaserOnOff T2X mmmm nnnn Error rate measurement mode T7 Error Rate TYYFFFFFFFFFF TYYmmmmmmllll Accumulated laser on time display mode TC LaserOnTim TCY mmmmmmh TC4* clear?? Picking up No. display mode TG OPU Number TGX YYYYYYY Test mode cancel TI Test Exit TI1 Really? 6.5. About the OPEN/CLOSE ( 5 )button Even during the test mode, the tray is opened and closed when the 5 button is pressed. 6.6.
  • Page 29 Error rate display details for each media type Measurement Remarks position The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T84 FFFFFFFFFF display. 2-layer The inner LDC error detection PI error detection It is invalid. When this is selected for 1-layer DVD circumference of signed number number or CD, T85 FFFFFFFFFF display. 2-layer The inner It is invalid. It is invalid. It is invalid. When this is selected for BD, DVD or circumference of CD, T86 FFFFFFFFFF display. 2-layer The central BIS error detection It is invalid. It is invalid.
  • Page 30 VERSION UPGRADE PROCEDURE OF FIRMWARE d You can update by downloading the latest firmware from the Internet. 1. Update from the Internet 1.1. preparation (1) System Requirement • Internet Connection by Broadband Circuit • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Setting Internet Computer...
  • Page 31 TROUBLE SHOOTING 1. POWER UNIT The power cannot be turned on. Defect of primary circuit component. ・[BD1] (RBV1506) ・[IC1] (STR-W6753) N.G. Check the FUSE condition. ・[U5] (STR-A6059H) [F101] (EER28(SW_TRANS)) ・FUSE ・[T1] ・[T2] (EI16(SW_TRANS)) and other circuits. O.K. Check parts and soldering. Check 5.5V_STBY output.
  • Page 32 2. DISPLAY UNIT 2.1. FL TUBE doesn't light. Check parts (surrounding) and soldering. (MR-6625UYB) ・[U3] N.G. POWER UNIT Check ±F output.（4.8V） (EER28(SW_TRANS)) ・[T1] (J1 #14-#16) ・[D19] (FR307) ※ 4.32V ～ 5.28V (20x1/W/HOUSING) ・[J1] and other circuits. O.K. Check parts (surrounding) and soldering. (PT6302) ・[U5] POWER UNIT...
  • Page 33 3. MAIN UNIT 3.1 Video out doesn't output. Check soldering. N.G. Check the input signal to [U18]. (NJM2566AV) and surrounding circuits. ・U18 ・Y6 (U18_6pin) ・[C544] ・[R567][R571] O.K. Check the power supply and control signal for [U18]. ・+5V_AV (U18_3pin) ・V_MUTE (U18_1pin) N.G.
  • Page 34 3.3. Analog audio doesn't output. Check the power supply voltage for [U801]. N.G. ・+12V (U801_8pin +11V Upper) Check the POWER UNIT. ・-12V (U801_4pin -12V Low） O.K. Check the input and output voltage for [U702]. N.G. Check the power supply voltage for [U802]. Check soldering.
  • Page 35 3.4 Digital Out(COAX) doesn't output. Check soldering. N.G. Correction of sordering. ・[C868][R868][R866][Q211][R862][R864][R863] Check the POWER UNIT. ・[R869][FB861] O.K. N.G. Check the output signal. Replace the MAIN UNIT. ・[FB861] Check the digital signal for 3Vpp. O.K. Replace [C868][R868][R866][Q211][R862][R864] [R863][R869]. 3.5. Ether is not connection. N.G.
  • Page 36 MEASURING METHOD AND WAVEFORMS 1. VIDEO section To check the waveforms(VIDEO) on the MAIN UNIT, the GND (-) probe to " t CE30" point. Measuring Disc: VIDEO/BLX-104 (Blu-ray disc) Playback Content : Title 1 , chapter 1 Color Bar 100% (Main Menu → 59.94Hz 1080i 1.Video signal → 1.Color Bar 100%) Component output resolution : 1080i (It is better to use wires for extending between the probe and test points.) Since there are no test points for locations q to r , confirm the signals at the land of a chip resistor.
  • Page 37 Terminal output check Signal: Color Bar 100% UD5005 Oscilloscope 75ohm Load Video out terminal check Video out_signal Component out terminal check Component out_Y signal Component out_Cb signal Component out_Cr signal...
  • Page 38 Personal notes:...
  • Page 39 BLOCK DIAGRAM BD Core Block (F/E, B/E) MAIN PWB Video Block MPEG DECORDER BD / DVD / CD [MT8530] VIDEO OUT DRIVE UNIT VIDEO DRIVER [NJM2566AV] FE CONT BD / DVD / CD COMPONENT OUT Mecha RF Signal AACS CPPM CPRM Pick up Re-Encode...
  • Page 40 WIRING DIAGRAM DISPLAY UNIT STANDBY-SW UNIT BtoB F-9332H SUB POWER DRIVE MECHA UNIT UNIT PH-PH P1.0 9P FFC 47P FFC 5P PH BtoB BtoB P1.0 P0.5 HA700 J700 HA600 MAIN UNIT P1.0 POWER UNIT PH-PH J306 P1.0 REMOTE UNIT AC INLET...
  • Page 41 PRINTED WIRING BOARDS MAIN (COMPONENT SIDE) MAIN (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 42 DISPLAY (COMPONENT SIDE) USB (COMPONENT SIDE) POWER (COMPONENT SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 43 DISPLAY (FOIL SIDE) USB- (FOIL SIDE) POWER (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 44 REMOTE (COMPONENT SIDE) REMOTE (FOIL SIDE) STANDBY-SW (COMPONENT SIDE) STANDBY-SW (FOIL SIDE) SUB POWE (COMPONENT SIDE) SUB POWE (FOIL SIDE) 鉛フリー半田 半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。 Lead-free Solder When soldering, use the Lead-free Solder (Sn-Ag-Cu).
  • Page 45 12k/1% 12k/1% 560/1% 560/1% 1.5k 1.5k 20PIN/FFC/1.0mm 20PIN/FFC/1.0mm LED_A 3.3k/1% 3.3k/1% LED_A LED_B LED_B 0.1uF/50V 0.1uF/50V U3 TL431 U3 TL431 W_REMOTE W_REMOTE FMEN-210A FMEN-210A 1.5k 1.5k PC817 PC817 TH1 2D22 TH1 2D22 3uH/5A 3uH/5A L2 3uH/2A L2 3uH/2A +12V MOTOR+12V 0.5A(Peak 2A) 5.5V_STBY 5V_STB...
  • Page 46 UD5005:0ohm 1SS355 9110S-09L NJM7809DL1A +12V +12V FBJ1608HS280NT FBJ1608HS280NT +12V 1SS355 MP2208 91K 1% AGND -12V 1000P EN/SYNC 0.01u 100K 0.01u MP2208 PGND1 PGND2 0.1u 47/16 3.3uH FBJ1608HS280NT 1SS355 47/16 FBJ1608HS280NT 22/16 100K 0.47[B] 0.1u[Z] UD5005:0ohm 1SS355 NJM79M09DL1A 9110S-14L FBJ1608HS280NT FBJ1608HS280NT...
  • Page 47 MR-6625UYB MR-6625UYB STBY_KEY V+VFD KEY_IN_B VCC_3.3V V+VFD GR12 GR11 V-VFD GR10 LED1 LED1 LED2 LED2 -32V ON/STANDBY FL OFF 100R 100R VFD_DATA 100R 100R VFD_CLK 100R 100R VFD_STB SG20 SG20 KEY_IN_A 2.7k 3.3k 5V_STBY SG19 SG19 IR_IN GR13 W_REMOTE SG18 GR14 SG18 R3 220R...
  • Page 48 OPEN 100pF GND_REN0 1000pF M3-SITE M3-SITE C20 0.01 C20 0.01 S401 SW S401 SW W_REMOTE IR_RC_EN IR_RC_IN Destination Setting RS232C_IN RS323C_OUT Reference UD5005 UD5005 UD5005 UD5005 UD5005 UD5005 UD5005 5V_NSW AMX_POWER N1SG S1SG MCU_SET1 OPEN MCU_SET2 MCU_SET3 5V_NSW 5V_NSW 0.1uF 0.1uF...
  • Page 49 A_KEY_IN R371 R371 BLM15P BLM15P FB27 FB27 KEY_IN_A PWR_AC_DET W_REMOTE W_REMOTE [13] B_KEY_IN R363 R363 BLM15P BLM15P FB25 FB25 KEY_IN_B PS_ON C1032 C1032 STB_KEY IR_IN IR_IN [13] B_KEY_IN C1034 C1034 KEY_IN_B KEY_IN_B [13] KEY_IN_A 3.3V KEY_IN_A [13] VFD_DATA 100pF/NC 100pF/NC 100pF/NC 100pF/NC VFD_CLK...
  • Page 50 1.8V U101 U101 U102 U102 U100A U100A A_DQ13 A_RA0 A_DQ16 A_RA0 A_DQ9 A_RA1 A_DQ22 A_RA1 1.8V C101 C101 C102 C102 C103 C103 C104 C104 C105 C105 C106 C106 C107 C107 A_DQ8 A_RA2 A_DQ21 A_RA2 0.1uF/16V 0.1uF/16V A_DQ11 A_RA3 A_DQ19 A_RA3 0.1uF/16V 0.1uF/16V 0.1uF/16V...
  • Page 51 U100B U100B U201 U201 U202 U202 B_DQ0 B_RA0 B_DQ18 B_RA0 B_DQ0 B_DQ4 B_RA1 B_DQ20 B_RA1 AR39 DVSS B_DQ0 B_DQ1 B_DQ2 B_RA2 B_DQ23 B_RA2 AW43 DVSS B_DQ1 B_DQ2 B_DQ1 B_RA3 B_DQ19 B_RA3 AU43 DVSS B_DQ2 1.8V B_DQ3 B_DQ6 B_RA4 B_DQ17 B_RA4 AU41 DVSS B_DQ3...
  • Page 52 FB200 FB200 1.2V BLM15P BLM15P U100C U100C 1.2V AVDD12_APLL FB206 FB206 HW TRAPPING AVDD12_HDMI C951 C951 BLM15P BLM15P NFREN NFREN [5,6] C927 C927 C953 C953 BE 1.2V:Below 0.1A NFWEN C952 C952 NFWEN [5,6] 0.1uF 0.1uF 0.1uF 0.1uF 10uF/10V 10uF/10V NFALE NFALE [5,6] 3.3V_VDAC...
  • Page 53 HW TRAPPING NAND 3.3V U100E U100E NFREN NFREN NFWEN FLASH NFWEN TP304 TP304 1.2V NFALE NFALE SFCS AVDD12_STX1 FB308 FB308 BLM15P BLM15P NFCLE 0402 NFCLE SFCS AVDD12_STX1 SFCK AVDD12_SRX1 FB301 FB301 BLM15P BLM15P U300 U300 SFCK AVDD12_SRX1 SFDI BE 1.2V:Below 0.1A NFCEN SFDI AVSS12_ST1...
  • Page 54 U100D U100D VCC3IO_STB 3.3V HW Trapping FB400 FB400 VCC3IO_STB1 BLM15P BLM15P ETCOL VCC3IO_STB1 ETCOL [12] ETCOL ETCRS VCC3IO_STB ETCOL ETCRS [12] C403 C403 C404 C404 ETCRS Close to 0402 (Test Mode) VCC3IO_STB ETCRS 3.3V_STBY 0.1uF 0.1uF VCC3IO_STB:Below 20mA ETMDC ETMDC ETMDC [12] ETMDC...
  • Page 55 U100F U100F 1.1V 1.1V VOUTVSYNC VCCK VOUTVSYNC V500 V500 VOUTHSYNC 3.3V AB20 VCCK VOUTHSYNC V501 V501 C537 C537 C538 C538 C523 C523 C526 C526 AD20 VCCK 10uF 10uF 0.1uF 0.1uF 4.7uF 4.7uF 4.7uF 4.7uF VOUTCLK1 EFVDDQ_CTL TP732 TP732 AF20 VCCK VOUTCLK1 V502 V502...
  • Page 56 M3.3V GIO14 /TRST FB604 FB604 AVCC BEFE_EX AVCC A1.2V GIO19 BLM18P BLM18P M3.3V GIO16 FE_RXIN FE_RXIN D3.3V GIO17 R648 R648 FE_RXIP FE_RXIP RTCK A3.3V C996 C996 GIO18 R649 R649 0.1uF 0.1uF C713 C713 C714 C714 GIO15 R652 R652 TGIO15 TGIO15 C691 C691 C690...
  • Page 57 MOTOR DRIVER GAINSW2 MOTOR GAINSW2 [8] MUTE2 MUTE2 V14REF R700 R700 R702 R702 MUTE1 MUTE1 R701 R701 R704 R704 MOTOR DRIVER V14REF R703 R703 R705 R705 TRAYPWM DRIVER TRAYPWM FB701 FB701 U700 U700 R706 R706 DMSO V14REF V14REF DMSO POWER BLM21P BLM21P DMSO...
  • Page 58 MIX 2CH L/R AUDIO CNT AMUTE AMUTE [4,6] U702 U702 NJM78L05uA NJM78L05uA AUDIO I2S AOMCLK AOMCLK MIX_+5V_DAC AOLRCK AOLRCK AOBCK 1SS301 1SS301 AOBCK AOSDATA0 CE20 CE20 AOSDATA0 DTA114EUA DTA114EUA 100uF/50v 100uF/50v 0.1uF 0.1uF +12VA SOT-89 SOT-89 MIX_OP+12V MIX_+5V_DAC AOSDATA4 AOSDATA4 CE24 CE24 CB12...
  • Page 59 ASPDIF CONNECTOR J861 J861 R862 R862 FB861 FB861 RCA2X3 RCA2X3 R863 2.2K R863 2.2K 1.8K 1.8K ASPDIF Q211 Q211 2N3904 2N3904 C868 C868 R868 68 R868 68 BLM15A BLM15A COAXOUT ML_OUT ML_OUT [10] C877 C877 C878 C878 MR_OUT R864 R864 R866 R866 R869...
  • Page 60 LAN-3.3V LAN_VDDA LAN-3.3V FB903 FB903 LAN_VDDA ETMDC ETMDC ETMDIO ETMDIO R931 10 R931 10 FB/0603 FB/0603 ETTXCLK ETTXCLK C975 C975 C976 C976 C977 C977 C978 C978 C979 C979 ETTXD0 ETTXD0 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 10uF 0.1uF/16V 0.1uF/16V ETTXD1 ETTXD1 C980...
  • Page 61 IIC ISP Interface MCU CS8966F GPIO LIST MCU_IIC_SDA CCIR_IN_Y9 CCIR_IN_Y9 [7] MCU_IIC_SCL NAME FEATURES AND NET RSTN TO MT8530 PIN MCU_2.5V MCU_3.3V 5V_STBY DC_DET P3.7 DC_DET 4x1/W/HOUSING 4x1/W/HOUSING MCU_3.3V FB21 FB21 MT8530_PS_ON# :H--->MCU UPGRADING MODE MCU_3.3V P3.6 MCU_SPI_DO Hi-Z Hi-Z R293 R293 MCU_SPI_DO...
  • Page 62 EXPLODED VIEW dh WARNING: Parts marked with this symbol have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.  印の部分は安全を維持するために重要 な部品です。従って交換時は必ず指定の 部品を使用してください。...
  • Page 63 7025HV1003011 NOTE : To replace the REMOTE PWB UNIT, please set a resistor according to 48 page of "Destination Setting". 5 963633100030S SUB POWER PWB UNIT ASSY 7025HV1002015 6 972631000060M DISPLAY PWB UNIT ASSY(UD5005) 7025HV1003212 USB PWB UNIT CHASSIS 3200213776100S...
  • Page 64 REAR PANEL(5005/K) 3207213796020S RUBBER SHEET (7X10X10.5) 4050213375000S 27 963685100020S DC FAN (RDL6025S_60X60X25) G720602504510S SPACER (D7.5X3.5XT1.0) 1530210302000S B 972402000290M FRONT PANEL ASSY(UD5005/B) B 972402000300M FRONT PANEL ASSY(UD5005/SG) FRONT PANEL (5005BK) 3067215188000S FRONT PANEL (5005SG) 3067215188010S MARANTZ BADGE (AL) FOR M1 MODEL 5630210678000S...
  • Page 65 13P CON. L002201130050S ★ 64 00MYU20100520 20P FFC N711201033810S PARTS LIST OF P.W.B. UNIT df Ref.No. Part No. Part Name Remarks Q'ty POWER PWB UNIT(UD5005) : Ref.No. 2 z F1 972652000210S FUSE(3.15AH/250V) G650202255510S z T1 972102000220S SW.TRANS 8200380285020S z JP1...
  • Page 66 PACKING VIEW sd...
  • Page 67 L063152030020S TWIN SHIELDED WIRE WITH RCA PLUGS L063102010110S BATTERY(R03X2) G670001R50220S 14 307010078008M RC005UD REMOCON UNIT C.G.DEVELOPMENT 8300005000010S 15 972531000380M CARTON CASE (UD5005) 6007211830020S CONT. LABEL (5005/U1B) SUB ASSY 5507000007500S CONT. LABEL (5005/N1B) SUB ASSY 5507000007500S CONT. LABEL (5005/N1SG) SUB ASSY...
  • Page 68 SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's CS8966-PQFP44 (Main UNIT : U16) VDD25 P1.2 / SDA / SWC0 P1.3 / SCL / SWC1 RSTN P1.4 / SWC2 P2.4 / T2EX / CMPD...
  • Page 69 I/O Port Definition Pin# Assignment Function Function Description Normal High(3.3V)/50Hz High(3.3V)/50Hz AC_DET Detection signal is for AC power. or 60Hz pulse or 60Hz pulse Muting signal is for component video(YUV) output. High is COMP_MUTE High(3.3V) Hi-Z(0V) for component video output is enabled. And low disable the component video output.
  • Page 70 PT6302 (Display UNIT : U5) Terminal Function Pin Name Description Pin No. SG5 to SG35 1 ~ 31 Segment driver output pin SG4 to SG1 64 ~ 61 l l i l l i Reset input pin RSTB When this pin is set to "LOW", all functions are initialized. Chip select input pin When this pin is set to "High"...
  • Page 71 MT8530 (Main UNIT : U100) Block Diagram HDMI, CVBS, Component Motor USB 2.0 Driver MT8530 Ethernet Audio DAC FLASH DRAM...
  • Page 72 PCM1781 (Main Unit: U802) (TOP VIEW) ZEROA DEMP0 DEMP1 MUTE AGND DATA LRCK TEST Terminal Function TERMINAL DESCRIPTION NAME AGND – Ground Audio data bit clock input DATA Audio data digital input (1) (2) DEMP0 De-emphasis control DEMP1 De-emphasis control (1) (2) (1) (2) Data format select LRCK Audio data left and right clock input...
  • Page 73 SMSC8710 (Main UNIT : U901) Block Diagram...
  • Page 74 NJM2566AV (Main UNIT : U18) Block Diagram...
  • Page 75 2. FL DISPLAY FL TUBE (15-BT-114GNK) (Display UNIT: U3)
  • Page 76 Personal notes:...

This manual is also suitable for:

Ud5005/n1sgUd5005/n1bUd5005/u1bUd5005/k1bUd5005/s1sgUd5005/s1b ... Show all