Ultra Signature Series, UF11240, UF11243, UF11245 Manual

Also See for Signature Series:

Table of Contents

Tools You Will Need

SAFETY TIPS

If you use soldering for the installation of the faucet, the seats, cartridges and washers will have to be removed before using flame. Otherwise, warranty will be void on those parts.
Cover your drain to avoid losing parts.
0℃~55℃.

Care & Maintenance:
* To keep the product clean & shining, follow the steps below:

Rinse with clean water & dry with a soft cloth.
Do not clean with soaps, acid, polish, abrasives, or harsh cleaners.
Do not use cloth with a coarse surface.
Unscrew the aerator and clean when necessary.
This installation manual is subject to change without further notice.
Please read your care and maintenance documentation to determine the limits of proper use.
This product has been manufactured and tested to the highest quality standards. We offer our customers thoughtfully crafted fixtures & accessories, engineered for enduring performance over years of use.

Prior to Installation:
Installation - Step 1

Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber's putty, or silicone.
Place bucket under angle stops. Turn on to flush any debris prior to installing new plumbing. Shut off angle stops.
Pre-drilled hole size requirement: 1-3/8" (min) – 1-1/2" (max)
Max countertop thickness without deck plate: 1-1/2"
Max countertop thickness with deck plate: 1"

For single hole installation, place faucet in directly. For three hole, place the base plate and escutcheon assembly (8&9) on bottom of faucet before inserting through the mounting hole. Pre-drilled hole size requirements: Faucet:Ø1-3/8"(min)~Ø1-1/2"(max)
Assemble rubber washer(22), metal washer(11) and thread mounting nut(12) onto shank(7) form underside of sink. Hand tighten, secure locking screws on mounting nut(12) and tighten locking screw using screw driver.
1. Place the new spray seat through on the mounting surface.
2. Assemble mounting nut onto shank form underside of sink. Hand tighten,
For Models with a Spray Support. Place faucet in position on the sink. Mount spray support in far right hole in sink. Insert spray hose down through the support and up through center hole of sink. Attach spray hose to Outlet tube nipple(10).
Thread hot & cold waterlines onto angle stops. Tighten with adjustable wrench until snug. Turn on the angle stops and check for leaks. (DO NOT TURN FAUCET ON)
After installation is completed, Remove aerator assembly(23). Turn water on for 1 minute to remove any debris. Reassemble aerator assembly(23).

If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:

Leakage under handle	Locking nut has come loose or cartridge needs to be reseated	Loosen the set screw located at the base of the handle with a hex wrench. Remove the handle and unscrew cartridge holder by hand. Tighten locking nut with an adjustable wrench.
Water will not shut off completely	Cartridge may need to be adjusted or replaced	Loosen the set screw located at the base of the handle with a hex wrench. Remove the handle and unscrew cartridge cover by hand. Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge. Check for cracks, and if O-ring is seated correctly, Reseat cartridge.
Leaking between spray head and hose	Spray head may be loose, or washer may not be seated correctly in the hose connection	Tighten the spray head by hand until snug, Make sure the washer is seated correctly.
Hose does not retract	Weight may not be installed correctly	Readjust the weight on the hose.

UF11240
UF11243
UF11245