Download
Share
Print this page
Samsung Jet Bot VR30T80313W/EU User Manual
  1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Vacuum Cleaner
  5. Jet Bot VR30T80313W/EU
  6. User manual
Samsung Jet Bot VR30T80313W/EU User Manual

Samsung Jet Bot VR30T80313W/EU User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Jet Bot
User manual
VR30T80**** series
• Before operating this unit, please read the instructions carefully.
• For indoor use only

Advertisement

loading
Need help?

Need help?

Do you have a question about the Jet Bot VR30T80313W/EU and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Samsung Jet Bot VR30T80313W/EU

Summary of Contents for Samsung Jet Bot VR30T80313W/EU

  • Page 1 Jet Bot User manual VR30T80**** series • Before operating this unit, please read the instructions carefully. • For indoor use only...

  • Page 2: Table Of Contents

    APPENDIX Safety information SmartThings App Setting up the wireless router INSTALLATION Downloading the SmartThings App Setting up a SAMSUNG account Installing a Docking Station Registering a device to the SmartThings App 28 OPERATION Software Update Functions of the SmartThings App...

  • Page 3: Preparation

    PREPARATION Accessories Accessories may differ depending on the models. Docking Station Pre-motor Filter: 2 units Side Brush: 2 units (Inside the product: 1 unit, (Inside the product: 1 unit, Spare: 1 unit) Spare: 1 unit) Battery Charger/Power cord Boundary Markers User Manual Safety information • Before operating the appliance, please read this manual thoroughly and retain it for your reference.
  • Page 4 Failure to meet these requirements could cause damage to the internal parts of the vacuum and void your warranty. General • Do not allow to be used as a toy. Close attention is necessary when used by or near children. •...

  • Page 5: Docking Station

    • For information on Samsung’s environmental commitments and product regulatory obligations, e.g. REACH, visit our sustainability page available via www.samsung.com Docking Station • Do not modify the polarized plug to fit a non-polarized outlet or extension cord. • Do not use outdoors or on wet surfaces.
  • Page 6 Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on.

  • Page 7: Power Related

    Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than rated volatge of the charger and also do not use a multi-outlet to supply power to a number of devices at the same time.
  • Page 8 • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.). – The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid. •...
  • Page 9 • For the very low areas where the Jet Bot may get stuck, set the No- go Zones with the SmartThing App or attach the Boundary Markers to prevent the Jet Bot from getting in. • Do not install the Docking Station in an area with a dark floor. –...
  • Page 10 In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet.

  • Page 11: Cleaning And Maintenance

    • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries from other products can cause malfunction.
  • Page 12 • Before cleaning, remove objects which are less than 9 cm height and are lightly on the floor as the Jet Bot can push along them, or the objects can be caught in the Jet Bot’s Side Brush or Driving Wheels. (Fixed objects can be detected by the Jet Bot when its bumper is pressed and will avoid them.) •...

  • Page 13: Installation

    INSTALLATION Installing a Docking Station Approximately 0.5 m Approximately Approximately 1 m 0.5 m 1 Connect the provided Battery Charger jack 2 Position the Battery Charger cord into the to the rear of the Docking Station. fixing groove at the rear of the Docking Station.

  • Page 14: Operation

    OPERATION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) 1 Open the upper cover of the Jet Bot and remove the white gasket. 2 Remove the yellow gasket attached to the power switch at the side of the Jet Bot and press the power switch to turn the Jet Bot...

  • Page 15: Auto Charging

    Auto charging The Jet Bot automatically returns to the Docking Station when it completes cleaning or when the battery is low to recharge. Docking (Recharging) You can return the Jet Bot to the Docking Station while cleaning to recharge. • Press the [ ] on the Jet Bot or use the SmartThings App to select the recharging function.
  • Page 16 Checking if the docking (recharging) does not work Check the Docking Station’s installation Charge the Jet Bot manually for the following status. conditions. • Check whether the Docking Station has • When the Docking Station is installed in a been installed in a place where the Docking corner Station cannot guide the Jet Bot to return.

  • Page 17: Operation

    OPERATION Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot ❇ ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. –...

  • Page 18: Operation Status On The Led Status Indicator

    Operation status on the LED Status Indicator Classification Color Meaning Blinking without An error occurs. moving While Blinking while Auto returning to the Docking operating moving Station due to low battery Operating stops due to low Jet Bot battery Red, orange, or yellow (depending While charging on charging progress) While...

  • Page 19: Cleaning Functions

    Cleaning Functions Cleaning Functions Operation • Auto Clean: Cleans automatically until the Jet Bot completes cleaning all rooms one time. Cleaning Methods • Room Clean: You can select a room you want to clean. • Spot Clean: You can set a specific area you want to clean. •...

  • Page 20: Additional Functions

    Additional functions Additional functions Operation • When charging is complete, the Jet Bot automatically enters the Sleep Mode. While the Jet Bot is docked on the Docking Station, press and hold the [ ] for 7 seconds to set it to the Sleep Mode. To cancel the Sleep Mode, start cleaning or press the [ ] for Energy-Saving...

  • Page 21: Attaching Boundary Markers

    Attaching Boundary Markers If Boundary Markers are attached before using the Jet Bot, the Jet Bot can operate safely. You can purchase additional Boundary Markers at a service center. To prevent the Jet Bot from entering the following areas, attach the Boundary Markers to the floor in a shape with 15 cm space distance.

  • Page 22: Parts Diagram

    Parts diagram Jet Bot 01 Obstacle Sensor 02 Power switch 03 LiDAR Sensor 04 Dustbin 05 Start/stop button 06 Docking (Recharging) button 07 Status Indicator 08 Docking Sensor Window 09 Upper Cover Bottom 01 Charging Pin 02 Brush 03 Brush Cover 04 Cliff Sensor 05 Roller 06 Battery Cover...

  • Page 23: Maintenance

    MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Grasp the Jet Bot’s cover at the groove 2 Hold the Dustbin handle and lift the and lift it up.

  • Page 24: Cleaning The Brush

    Cleaning the brush 1 Push the Brush Cover Lock to the right 2 Detach the brush cover. to unlock. 3 Lift up the left side of the brush first and 4 Clean the brush. then pull the brush from the groove on the right.

  • Page 25: Cleaning The Sensor Window

    Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Docking Sensor Obstacle Cliff Sensor Window Sensor LiDAR Sensor Dust Sensor Rear Sensor Cleaning the Driving Wheel 1 Place a soft cloth down first, turn the Jet 2 Remove foreign matter with a blunt rod or Bot over, and place it gently on the cloth.

  • Page 26: Cleaning The Side Brush

    Cleaning the Side Brush Cover the Side Brush with a hot steamed cloth When the Side Brush is very tangled with for 10 seconds, then wipe the Side Brush. hair, threads, etc., detach the Side Brush with a screwdriver while gripping the Side Brush, and remove the foreign matter.

  • Page 27: Appendix

    • SAMSUNG Jet Bot supports IEEE 802.11b/g/n and Soft-AP. – IEEE 802.11n is recommended. • SAMSUNG Jet Bot supports only DHCP (Dynamic Host Configuration Protocol). Please make sure that the DHCP server option is activated on your wireless router. • The Jet Bot supports the WEP-OPEN, WPA-PSK/TKIP, and WPA2-PSK/AES for the authentication and encryption protocols.

  • Page 28: Downloading The Smartthings App

    • To set up a SAMSUNG account, you can follow the directions provided by the SmartThings App. • Or, if you have a SAMSUNG smartphone, you can add your SAMSUNG account in the setting app of your smartphone. Then, it will automatically sign in to your SAMSUNG account and you can use the SmartThings App.

  • Page 29: Software Update

    4 [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [vacuum]_E30AJT** in the Wi-Fi list. 5 Provide the authentication when you are directed to do so. 6 [Android] The connection to your wireless router will be progressed automatically. –...

  • Page 30: Functions Of The Smartthings App

    Functions of the SmartThings App Classification Functions Explanation • You can check the result of the last cleaning. Monitoring Cleaning Report • You can check the histories of last 50 cleanings. • You can stop cleaning and have the Jet Bot Dock return to the Docking Station.
  • Page 31 Classification Functions Explanation • When cleaning is complete, you can receive Cleaning completed cleaning completion notice. Notice • If the Jet Bot needs to be checked, you can Check Notice receive a notice. • You can set a zone where you do not want the Jet Bot to clean.

  • Page 32: Notes And Cautions

    Notes and cautions Installation NOTE • Install the Docking Station in a place where the floor and wall are level. • If the cleaning area is wooden floors, it is best to install the Docking Station along the grain of wooden floors. •...

  • Page 33: Using

    • If the Jet Bot is left detached from the Docking Station, the battery will drain naturally. – Try to keep the Jet Bot being charged on the Docking Station. (However, turn off the power switch and leave the Docking Station unplugged when planning to leave the house for long periods of time by going on a business trip or vacation, etc.) Using...

  • Page 34: Cleaning And Maintenance

    • If it is difficult to remove foreign matter from the brush, contact an authorized SAMSUNG service center. • Since the brush sweeps dirt up from the floor during cleaning, foreign matter such as a thin and long thread, long hair, etc. may get caught in it.

  • Page 35: Battery Usage

    • This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble or modify the battery.

  • Page 36: Corrective Measures Before Reporting A Problem

    Corrective measures before reporting a problem 1 The Status Indicator 2 Turn off the power 3 When turning the Jet turns red and blinks switch and check the Bot on by pressing with a voice guide. instructions below the power switch, the and take appropriate Status Indicator turns actions.
  • Page 37 Voice Guide Checklist The LiDAR sensor needs to be • There is a problem with the LiDAR sensor. reset. Turn the power off, then on – Turn the power off, then on again. If the notice again. If that doesn't fix it, contact remains, contact Customer Service.

  • Page 38: Troubleshooting

    Troubleshooting Symptom Checklist • Check if the power switch is on. • Check if the Status Indicator is on. • Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Docking The Jet Bot is not working at all.
  • Page 39 Symptom Checklist The Jet Bot does not detect the • Make sure the Boundary Markers are attached as ( Boundary Marker and crosses shape at 15 cm before the locations where the Jet Bot the boundary. should not cross. • Check if the Docking Station is installed along the grain of wooden floors or tiles.
  • Page 40 • Connect the Jet Bot to a wireless router by referring to App, but the Jet Bot fails to be the ‘SmartThings App’ of the user manual. connected. I fail to log into the SAMSUNG • Check your ID and password on the screen of the account. SAMSUNG account.
  • Page 41 SmartThings App". • When the product registration fails repeatedly, restart the SmartThings App and try the product registration. • All users should use the SAMSUNG account issued by the country which launches the product. (Applicable to iOS only) During product registration, the AP •...
  • Page 42 ❇ ❇ Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support >...

  • Page 43: Open Source Announcement

    The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It is also possible to obtain the complete corresponding source code in a physical medium such as a CD-ROM;...

  • Page 44: Product Specification

    Product Specification Classification Items VR30T80**** series Weight 3.4 kg Mechanical LiDAR location recognition Cleaning method specifications Touch type Button method of the Jet Bot Power consumption of the 60 W (Spot Clean) Electrical Jet Bot specifications Battery specification Lithium-ion 21.9 V / 52.56 Wh Charging type Auto charging / Manual charging Cleaning Functions...
  • Page 45 Memo English 45...
  • Page 46 DJ68-00857G-03...

This manual is also suitable for:

Jet bot vr30t80313wJet bot vr30t80 series