Download Print this page

Dedenbear CC-3 Installation & Operation Manual

Command center 3

Advertisement

Quick Links

INSTALLATION
INSTRUCTIONS
COMMAND CENTER 3 INSTALLATION & OPERATION MANUAL
Installation Instructions............... ...... pg 1
Pro-Full Feature.................. ............ pg 2
Button Use & Programming... . . . . . . . . . . . . . pg 2
Types of Delay Boxes ....................... pg 3
Setting Transbrake Delay .................. pg 3-4 Throttle Stop & Nitrous Wiring ............ pg 9
Setting Throttle Stop Types & Timers... pg 4-5
Starting Line Control......... ... ............ pg 5
Super Start System ... ...... ............ ..... pg 5
INSTALLATION
Using #8 screws through the rubber grommets in the base, mount the Command Center away from heat, vibra­
tion and the ignition system.
Make sure the driver can reach the buttons when strapped in and angle the unit if needed so the display can be
read straight on. If the box is mounted so the display is viewed more than 10 degrees off center, it will be hard to
read.
Wire the Command Center as shown on pages 8-11. Make sure the power lead comes straight from the master
switch and the ground goes to a solid chassis ground, not sheet metal panels.
BUTTON QUICK REFERENCE
OUTPUT
INDICATOR
LEDS
C)
C)
€)
€)
C)
RESET / RECALL
MODE
SELECTION
DEDENBERR
=================
P ROD U C TS
BACKLIT
DISPLAY
T.STOPB
RPM SWITCH
COMMAND CENTER
START LINE
DEDENBEAR Products , Inc.
413 West Elm Street, Sycamore, IL
T.STOPA
TRANS BRK.
1:ooel I
///�@
/
RPM SWITCH OR
THROTTLE STOP -C
SET-UP
,
IN C .
INDEX
RPM Switch & Throttle Stop C ... . . . . . . . . pg 6
Digital Tachometer .......................... pg 6
General Info/ Definitions ......... ... ....... pg 7
Transbrake Wiring ...... ... .................. pg 8
Linkage Style Stop Wiring... . . . . . . . . . . . . . . pg 1 O
RPM Switch & Remote Display Wiring. pg 11
Setting Parameters ... ... .................... pg 12
PRO-FULL
BUTTON
Model CC-3
60178 (866) 248-6356
I
RPM
THROTTLE
THROTTLE STOP -A
STOP-B
AND STARTING LINE
SET-UP
CONTROLLER
--=---
=·�
--
MODEL NUMBER
!!�
SCROLL
ARROWS
II1 0 0•
[!]00
e
0
..._ ___ _
r:;-,
r;::::i
7
SET-UP
CC-3
LIGHTED
NUMERIC
KEYPAD
PRO-FULL
INDICATOR
LED
///
------
TRANSBRAKE
SET-UP
REMOTE
DISPLAY
CONNECTOR
PAGE1

Advertisement

loading
Need help?

Need help?

Do you have a question about the CC-3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dedenbear CC-3

  • Page 1 PRO-FULL [!]00 INDICATOR RPM SWITCH COMMAND CENTER €) START LINE • Model CC-3 ------ TRANSBRAKE DEDENBEAR Products , Inc.._ ___ _ SET-UP €) 413 West Elm Street, Sycamore, IL T.STOPA r:;-, r;::::i 60178 (866) 248-6356 � � TRANS BRK.
  • Page 2: Programming Buttons

    The CC-3 has many selections that can be programmed for each setting. Each time you push the button for the particular setting you are adjusting, it will step you to the next prompt screen. The CC-3 will only ask for the set­...
  • Page 3 To set your transbrake delay you must first choose which delay box type you wish to run by pressing the MODE button. The CC-3 will only ask you for the settings required for that particular mode. Example: When you are in RUN (DELAY) it will not ask you for THEIR ET setting since you are not crossing over.
  • Page 4 THROTTLE STOP The CC-3 has 2 separate 4 stage throttle stop controllers (a 3rd controller is available if the RPM output is not used. See the RPM switch section for details) plus an independent Starting Line Control (SLC) output. The throttle stop outputs can be used to time just about any 12 volt device.
  • Page 5 SLC s (s divid al d ipti ll o l th t the St enu a the CC-3. This t is wir styl ol y g­ g RPM i us w ys. Press ld th "R" flip thr...
  • Page 6 200 RPM s ift t 2-3 a RPM. Ev rans­ ode t brake is appl t an e CC-3 will go back 1-2 s ft . RPM OR ffilMSlt r1� to t . · · < TIMER · · • ·...
  • Page 7 "FIRST HIT BY: .023". This means that you were quicker leaving off your top bulb than your second bulb and that you were . 023 seconds quicker. The CC-3 released the trans brake off the top bulb hit in this example. If you had cancelled the first two hits by pressing the button a third time, the display would read "LAST CHANCE ACTIVATED".
  • Page 8 Supply power to the other side of the transbrake button from the +12 volt terminal on the CC-3 using 14 gauge wire. If you wish to use the optional skip button, supply power to one side of the button from the CC-3's +12 volt terminal using 18 gauge wire.
  • Page 9 WIRING FOR BASEPLATE STYLE THROTTLE STOPS For electric "butterfly" throttle stops set stop A to "BASEPLATE TYPE". CC-3 i � g�., :.:: � (])(]) _.w i ;;:; � �u l � ci,i� > a: z � � o(])(])o For air "disc" throttle stops set stop A to "LINKAGE TYPE".
  • Page 10 In this application simply wire your linkage type throttle stop directly to the STARTING LINE CONTROL terminal on the CC-3. You can access the SLC options 18 GAUGE by pressing the STOP A button. WIRING FOR DOWN TRACK E.T. CONTROL CC-3 �"'...
  • Page 11 These style solenoids use voltage to push the shift lever and make the gear change. You MUST use a relay or starter solenoid to avoid damage to the CC-3.
  • Page 12: Service And Warranty

    12 month warranty period will be repaired or replaced at DEDENBEAR’s option, when determined by DEDENBEAR that the product failed due to defects in material or workmanship. This warranty is limited to the repair or replacement of parts in the DEDENBEAR Product and the necessary labor done by DEDENBEAR to effect the repair or replacement of the DEDENBEAR product.