Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for MechMaxx WB855
Summary of Contents for MechMaxx WB855
- Page 1 WARRANTY Operator’s Manual www.mechmaxx.com...
-
Page 3: Table Of Contents
FUNCTION TRANSFORMATION KEY COMBINATION OPERATION SWITCH ON THE MAIN SWITCH WHEEL MOUNTING A：FRONT CONE MOUNTING B: BACK CONE MOUNTING C: SPECIAL MADE FLANGE MOUNTING WHEEL PARAMETER INPUT SELECT BALANCE MODE BALANCE THE WHEEL OPT UNBALANCE OPTIMIZATION www.mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model WB855 Voltage 110v/ 60hz /1 phase Motor Power 1/3 HP Rim Diameter 10-24 in Voltage 110v/ 60hz/1 phase Motor Power 1/3 HP Rim Diameter 10-24 in Shaft Size 40 mm Max Wheel Diameter 40" Rim Width 1.5-20 in... -
Page 5: Introduction
- Periodically clean plastic panels and frames with deter- gent. - Operators should not wear ties, long hair, and loose clothing. When the tyre is rotating, the operator should stand at the side of the equipment and the non-operator should not approach. www.mechmaxx.com INTRODUCTION... -
Page 6: Display Control Panel
10. Dynamic/static imbalance selection key (F)-dynamic-static-dynamic 11. Balance mode selection key ALU-S mode-balance mode1- balance mode 2- balance 12. Self calibration key mode 3-S mode 13. OPT key 14. STOP key 15. Accurate wheel balancing key(＜5g key) www.mechmaxx.com DISPLAY CONTROL PANEL... -
Page 7: Operation
Note: The choice on the cone should be adapted to the rim Main shaft―wheel (direction of the rim installation center hole and pay attention to its direction. Or it will surface is inside) ―suitable cone (small side inside) ― cause the inaccurate measurement. wheel―quick nut www.mechmaxx.com OPERATION... -
Page 8: Wheel Parameter Input
“A” (such as the control panel diagram).The default balance Press “+”to increase the value mode is dynamic balance,t he display window does not Press “-”to decrease the value show. Until you get correct value. (2) Input width “B” www.mechmaxx.com OPERATION... -
Page 9: Balance The Wheel
10g lead directly above the vertical shaft on the outside of the rim. As shown in figure: ALU3---- The inner ring clamps the balance lead, and the outer side adheres to the balance lead (the position of the outer side balance lead is like ALU2). www.mechmaxx.com OPERATION... -
Page 10: Opt Unbalance Optimization
Display [—→—][ 180 ] the display screen shows "180" that means the rims and tires should rotate 180 degrees each other and be reloaded back into the balancer. www.mechmaxx.com OPERATION... -
Page 11: Maintenance And Repair
4. When self-calibration is carried out according to “self-calibration” steps "1" to "2", 100g lead are added on the marked points, and finally pls see the self-calibration results. As shown in figure: 100g lead is added on underface, the indicator light will be on www.mechmaxx.com MAINTENANCE AND REPAIR... -
Page 12: The Abnormal Phenomenon And Solution When Self-Calibration
3. Press A key “＋” shown as picture 3, This can be used release when the light goes out. to adjust the static balance parameter. If there is too much deviation, please correct it to the graphical data. Pic.1 Left display window Right display window Pic.3 Standard memory www. mechmaxx.com MAINTENANCE AND REPAIR... - Page 13 If the above opera- tion is invalid, please contact the manufacturer. Note: 1200 large balancer self-calibration pls press R key and START key www. mechmaxx.com MAINTENANCE AND REPAIR...
-
Page 14: Trouble Shooting
2.Dry and reset the sensor 2. sensor is damp or lock nut not 3.Screw the anchor tightened 3. The external power supply voltage is low, the tire pressure is insufficient or the matcher is not tightened, etc www. mechmaxx.com TROUBLE SHOOTING... - Page 15 1. Readjust, dry and then self - calibration left and right interference, or replace 2. Program chaos difficult to show 00 2.self-calibration No brakes after display value 1. Brake system damage 1. Replace power board 2. external disturbance 2. restart www. mechmaxx.com TROUBLE SHOOTING...
- Page 16 info@mechmaxx.com...
Need help?
Do you have a question about the WB855 and is the answer not in the manual?
Questions and answers