Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for MechMaxx WB857
Summary of Contents for MechMaxx WB857
- Page 1 WARRANTY Operator’s Manual www.mechmaxx.com...
-
Page 3: Table Of Contents
HOOD SETUP UNPACKING INSPECTION WEIGHT UNIT SETUP OPT PROGRAM MACHINE INSTALLATION DISPLAY WINDOW（G） PRESS BUTTON FUNCTION（H） OPERATION STANDARD BALANCE MODE ALU-2 BALANCE MODE ALU－S BALANCE MODE SET THE OPTION SLC TO ON ALU－S BALANCE SPLIT OPERATION www.mechmaxx.com TABLE OF CONTENTS... -
Page 4: Specifications
SPECIFICATIONS Model WB857 Voltage 110v/ 60hz /1 phase Motor Power 1/3 HP Rim Diameter 10-24 in Shaft Size 40 mm Max Wheel Diameter 40" Rim Width 1.5-20 in Max Wheel Weight 154 lbs Calibration Wheel Recommended 15 in steel rim wheel... -
Page 5: Warning
ST motorcycle dedicated mode, DYN dynamic balance, ALU1 aluminum alloy, ALU2 aluminum alloy and ALU3 • Altitude：≤4000 meters aluminum alloy free paste mode (total 6 kinds of mode) to • Relative humidity：≤85％ balance all kinds of car wheel shape. www.mechmaxx.com WARNING... -
Page 6: Installation
The equipment must be installed on a solid cement floor or similar. If the ground is not solid, measurement error will be caused. There should be space left around the equipment for easy operation. See below: www.mechmaxx.com INSTALLATION... -
Page 7: Press Button Function（H
3.input①ai②ae③ d value 4.start,wait until it stops PRESS BUTTON FUNCTION（H） Icon Function description Icon Function description Distance caliper head to the inner rim OPT program Balance mode slection Input wheel width www.mechmaxx.com INSTALLATION... - Page 8 Icon Function description Icon Function description Input rim diameter Combination/division Bisplay actual unbalance value Recalculate the balance results Start Stop or cancel www.mechmaxx.com INSTALLATION...
-
Page 9: Operation
4）put down the hood or press key to rotate the wheel. 5）After the wheel stops, the digital tube displays unbal- anced result, press key to read actual unbalance weight. main shaft—tower spring (spring is installed inside shaft)suitable cone (big side inside)—wheel-pressure cup-quick nut www.mechmaxx.com OPERATION... -
Page 10: Alu-2 Balance Mode
12 o 'clock is the position for sticking imbalance weight. Weight placement positions are as shown in below pictures. Stick corresponding balance weight on the outer of the wheel rim. See pic.6. www.mechmaxx.com OPERATION... -
Page 11: Alu－S Balance Mode
12 O’clock is the unbalance point of alignment plane. Balance alignment planes are as shown in below pictures. Paste corresponding balance weight on the outside of the wheel Pic.7 rim. See pic.10 www.mechmaxx.com OPERATION... -
Page 12: Set The Option Slc To On
4.2 Tear out the suitable weight lead(Pic.15) and place it on head of ruler (Pic.16), Pic.15 Pic.16 4.3 Pull out the ruler until to see the position of outer unbalance point on rim outside (Pic.17) Pic.17 Pic.11 www. mechmaxx.com OPERATION... -
Page 13: Alu－S Balance Split Operation
Pic.21 4.8 After placing the weight lead, press key or put down the hood,pic.22 is shown. It indicates that the balancing is successful. The operation is successful! Pic.22 www. mechmaxx.com OPERATION... -
Page 14: Calibration
DISTANCE RULER CALIBRATION （optional function） display ＞ display Pull out the ruler to zero position and press key to confirm ＞ display Pull out the ruler to 15 position and press key to confirm ＞ Self-calibration is successful！ www. mechmaxx.com CALIBRATION... - Page 15 （ for example,if it is 14 inch, then in put 14） display ＞ display Pull out the ruler to the rim of the tire and hold it ＞ display Then press key to confirm, which is indicating finished ＞ Self-calibration is successful！ www. mechmaxx.com CALIBRATION...
-
Page 16: Trouble Description
1. Check or replace travel switch. 2. Check or replace computer panel. 2.Computer panel is something wrong. 1.Computer panel is crashed. 1.Check or replace computer panel. 2.Power panel is something wrong. 2. Check or replace power panel. www.mechmaxx.com TROUBLE DESCRIPTION... -
Page 17: Trouble Shooting
（optional） direction Value showed in window varies 327-335 Width ruler sensor when rotate the ruler rod to the other （optional） direction Value varies from 4X-4X to 6X-6X when you Pressure sensor press the main shaft. www.mechmaxx.com TROUBLE SHOOTING... -
Page 18: Parameter Setup
The machine has the following functions, which can be adjusted according to your own requirements. Function Screen displayed Function Definition sequence hood Put down hood to start hood Put down hood+ key to start www.mechmaxx.com PARAMETER SETUP... -
Page 19: Weight Unit Setup
The machine has the following functions, which can be adjusted according to your own requirements. Function Screen displayed Function Definition sequence Weight unit Weight results show grams Weight unit Weight results show ounces www.mechmaxx.com PARAMETER SETUP... -
Page 20: Opt Program
Make a mark at rim D and tire C, demount the tire display from the rim and then mount it again to make ＞ ＞ these two points overlap with each other. display Unbalanced weight is less than before is When done,put down the hood, press ＞ successful www.mechmaxx.com OPT PROGRAM... - Page 22 info@mechmaxx.com...
Need help?
Do you have a question about the WB857 and is the answer not in the manual?
Questions and answers