Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Sunmax RT35
Summary of Contents for Sunmax RT35
- Page 1 RT35 Hand-Pushed Floor Scrubber User Manual sunmaxus.com...
-
Page 2: Table Of Contents
Contents Machine Performance and Applications..................2 Machine Delivery...........................2 Packing List...........................2 Performance Parameters........................2 Meaning of Warning Symbols.......................3 Warning............................4 Disclaimer............................4 Notes for Machine Use........................4 Preparation and Configuration of the Machine Preparation Before Opening the Machine..................6 Introduction to the Machine......................7 Battery Charging Connection......................7 Battery Maintenance........................7 Battery Disposal..........................8 Battery Charging...........................8 Battery Charging Status Indicator Table..................8... -
Page 3: Machine Performance And Applications
Machine Performance and Uses This machine is a floor cleaning machine that combines mechanical friction of brush plates with chemical cleaning agents. It is suitable for cleaning various types of floors, and dirty materials and water on the floor are sucked dry by the rear squeegee. As long as you use and maintain the machine correctly, any of our products can operate efficiently and effectively. -
Page 4: Meaning Of Warning Symbols
Meaning of Warning Symbols Beware/Caution Repeated Use Read Manual Information/Supplementary Instructions Watch Out for Pinching Watch Out for Corrosion Watch Out for Injury to Hands Watch Out for Electric Shock No Smoking Hazardous Waste Beware of Volatile Gases Handling Equipment Loading/Unloading... -
Page 5: Warning
1.Warning For the safety of operators and the machine, it is necessary to carefully read all content marked with this symbol before use. Be cautious of evaporating gases and corrosive substances that may spill. Keep the machine away from ignition sources. For this reason, we recommend that you carefully read this user manual before use, and we hope that you will read it again if the machine experiences operational issues. - Page 6 15. Do not operate near shelves or scaffolding with falling hazards. 16. Select the appropriate operating speed based on traction conditions. 17. To prevent instability, it is prohibited for the machine to operate on slopes exceeding the allowed conditions. 18. When parking the machine, remove the key and place it on a flat surface. 19.
-
Page 7: Preparation And Configuration Of The Machine Preparation Before Opening The Machine
First, Preparation and Configuration of the Machine Preparation before Unboxing 1.This machine is packaged in a specially designed wooden crate, which can be handled with a forklift. The machine can only be placed in two layers. 2.The dimensions of the packaging box are as follows: Length: L=39.8 inches, Width: W=22.8 inches, Height: H=38.2 inches. -
Page 8: Introduction To The Machine
Machine Introduction A: Handle B: Key Switch C: Battery Level Display E: Brush Switch F: Drain Pipe Plug G: Filter H: Suction Switch I: Solenoid Valve J: Adjustment Nut L: Battery Cable N: Water Valve Adjustment P: Suction Inlet Q: Suction Squeegee Bracket R: Clean Water Tank Filter S: Drain Pipe T: Suction Tube U: Dirty Water Tank Lid V: Dirty Water Tank W: Battery Plug (Male) X: Clean Water Tank Y: Suction Squeegee Z: Battery Battery charging connection (see image below) -
Page 9: Battery Disposal
Battery disposal When the battery life is exhausted, the connection should be cut off by a special person and removed from the battery compartment in a corresponding way. Batteries are hazardous wastes and should be disposed of in a timely manner after the storage is exhausted. -
Page 10: Installation Of Squeegee
Installation of Squeegee Assembly Due to the relationship of packaging, the suction squeegee is supplied separately, and the suction squeegee Y should be fixed on the suction squeegee bracket assembly Q as shown in the above figure, until the cable is loosened, and the suction pipe T is connected to the suction port P. -
Page 11: Clear Water Tank
Sewage tanks Turn over the sewage tank, check the connection between the suction pipe, the sewage pipe and the sewage tank, see whether the parts are connected correctly and sealed well, and further check whether the sewage suction pipe T and the suction port P, the sewage pipe S and the sewage pipe plug F are connected correctly and sealed well. -
Page 12: Installation Of Brush Plate
Installation of the brush 1. Before installing the brush disk, be sure to keep the power supply of the machine in the off position, that is, turn the key switch B to the 0 position; In order to avoid injury to the hands, all power supply of the machine should be cut off before the brush plate installation operation. -
Page 13: Operation Of The Machine Pre-Operation Settings
Second, the operation of the machine Set up before work 1. Connect the battery plug M; 2. Set the master switch key B to the 1 position (clockwise), and the power indicator H will light up immediately. 3. The water valve N manually adjusts the amount of clean water, and selects the appropriate amount, which is enough to clean the floor and will not overflow from the outside of the baffle. -
Page 14: Overflow Device
Overflow device When the water in the tank is full, the float in the tank is closed The suction pipe, in order to avoid damage to the suction motor, should be opened immediately, and stop the machine from working and empty the sewage tank. This process must be operated with gloves to avoid contact with dangerous goods. -
Page 15: Daily Maintenance Cleaning Of Wastewater Tank
Third, Daily maintenance Clean the sewage tank 1. Remove the sewage discharge pipe; 2. Unplug and empty the dirty water tank; This process must be operated with gloves to avoid contact with dangerous goods. 3. Clean the sewage tank with a water hose or spray gun, and discharge all the sewage;... -
Page 16: Cleaning Of Battery Box
Clean the battery compartment Wipe the battery box and battery with a dry rag regularly, keep it clean, and check whether the connections of the battery power cord, including the binding posts, are loose, please keep the connection tight and strong, otherwise it will easily lead to overheating, affecting the normal charging and battery life. -
Page 17: Common Faults And Troubleshooting
Fifth, Common faults and troubleshooting methods Before entrusting the maintenance department or calling our customer service department, please check the following points: phenomenon Causes Solution 1.Check that the power cord plug is plugged 1.Plug in the power plug properly; in correctly; 2.Properly check circuit fuses such as fuses 2.Check that the power socket is plugged in;...
Need help?
Do you have a question about the RT35 and is the answer not in the manual?
Questions and answers