Subscribe to Our Youtube Channel
Related Manuals for Bigger Boyz Toyz BBT-LM-ER-26
Summary of Contents for Bigger Boyz Toyz BBT-LM-ER-26
- Page 1 OWNER’S MANUAL Assembly & Operating Instructions 26” RIDER-ON LAWN MOWER BBT-LM-ER-26...
- Page 2 Customer Support Before initiating a product return, kindly reach out to our dedicated Customer Support Department at Bigger Boyz Toyz. We are here to assist you. Phone: 02 4257 4787 Email: bbt@bbta.com.au Warehouse: Unit 2/3 Delta Place, Albion Park Rail NSW 2527 If you have difficulty assembling the product or have any questions about the controls, operations, or maintenance of the equipment, please don’t hesitate to get in touch with our...
-
Page 3: Table Of Contents
REVERSE CUT ....................... 20 GRASS CATCHER EMPTYING ..................21 AFTER USE ........................22 STORAGE OF BATTERY ....................23 MAINTENANCE ..................24 ENGINE SERVICE ......................24 MAINTENANCE SCHEDULE ..................24 SPECIFICATION ..................25 TROUBLESHOOTING ................26 BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 4: Safety & Alert Symbols
Some illustrations may not be applicable to your equipment. WARNING Your Responsibility—Restrict the use of this equipment to persons who have read, understood, and will follow the warnings and instructions in this manual and on the machine SAVE THESE INSTRUCTIONS! BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 5: Hazards Symbols
Stop equipment if anyone enters the area. SINGLE OPERATOR: Only one person should operate the equipment at a time. RISK OF MACHINE ROLL-OVER: Do not use the machine on slopes exceeding 10° DO NOT use in the rain. BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 6: Components Of The Mechanical Machine
COMPONENTS OF THE MECHANICAL MACHINE Steering wheel Seat Grass bag Brake pedal Gear shift lever Blade clutch handle Clutch handle Cutting pedal when backward Parking handle Cutting height adjustment handle Start key Cleaning connection BIGGER BOYZ TOYZ • BBTA.COM.AU... - Page 7 Grass Bag Installation Seat Installation Steering Wheel Installation Rear Plate Installation Blade Clutch Handle Installation Cutting Height Adjustment & Speed Handle Fuse, Charger and Ignition Key Tooling Sets and Funnel Side Discharger BBTA.COM.AU • BIGGER BOYZ TOYZ...
-
Page 8: General Safety
Do not create any source while refuelling of ignition until the petrol vapours have evaporated » Add fuel before starting the engine. Never remove the cap of the fuel tank or add BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 9: Work/Machine Area
6. Release the cutting device, stop the engine and remove the ignition key to ensure that all moving parts have stopped completely: BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 10: Operation
» Limit loads to those you can safely abnormally (check for the causes control. immediately). » Do not turn sharply. Use care when 12. Disengage the blades for transport or reversing. whenever they are not in use. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 11: Maintenance, Storage And Storage Transport
This waste must not be disposed of instead send it to a waste treatment together with ordinary waste, but must be facility in accordance with current local separated and sent to a collection centre, regulations. which will recycle the material. BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 12: Assembly
Step 4: Take the following precautions to remove the machine from the packaging: » Move the machine assembly to its maximum height to prevent damage when the machine is lifted from the base tray. » Lift the machine off the base plate. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 13: Steering Wheel Installation
First Insert the sleeve into the steering wheel shaft, as shown in Figure 1, then Insert the decorative cover as shown in Figure 2, insert the steering wheel and fix by bolt (M8x160) and washer, install the decorative cover as shown in Figure 3. BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 14: Seat Installation
(Align the holes on the seat with the holes on the fixing plate, secure the seat with bolt (M8x20) washers, as shown in below Figure.) Fix the seat on the machine by bolt (M8x18) and nut (M8). Under the seat, Connecting the switch plug properly. BIGGER BOYZ TOYZ • BBTA.COM.AU... - Page 15 Step 2: Combine the below 2 type of metal frames together as below picture. Step 3: Combine the grass bag with the metal frame as shown in the below figure. Step 4: Combine the grass catcher and top cover by screws (ST5.0x16 and ST5.0X35). BBTA.COM.AU • BIGGER BOYZ TOYZ...
- Page 16 Please note: the grass bag must be installed properly before cutting, otherwise the engine cannot start. Installed the grass bag in right place. Note: Cutting safety protection switch 6. ASSEMBLY OF THE HANDLE INSTALLATION Fix the handle as the below pictures. BIGGER BOYZ TOYZ • BBTA.COM.AU...
-
Page 17: Using The Machine
The machine can be used to mow lawns in many different ways; Before you begin, prepare your machine according to how your lawn will be mowed. Step 1: Preparation for grass mowing and chopping (mulching function) Install the mulching plug as shown on the below pic BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 18: Start-Up
START-UP Step 1: Sit on the operator’s position. Step 2: Put the drive in neutral as shown in the below figure. (for mechanical type) Step 3: Blade clutch at CLOSE “A” position. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 19: Drive Without Cutting
Step 3: Fully press down the brake pedal and move the gear shift lever to the first position (to control the speed according to adjust to different position), then release the brake pedal slowly. (for mechanical type) BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 20: Cutting
“N” (For mechanical model). Step 3: Blade clutch at OPEN “B” position. Step 4: Press the “REVERSE CUT” pedal when reverse cutting, for the mechanical model move the gear shift lever to the position “R”. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 21: Grass Catcher Emptying
Step 1: Reduce engine speed. Step 2: Engage the parking brake if on slopes. Step 3: Take hold of the rear lever and tip the grass catcher bag up to empty it. BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 22: After Use
Step 5: Remove the key. AFTER USE Step 1: Allow the engine to cool before storing in an enclosed space. Step 2: Clean. Connect the water pipe with the water nozzle to clean the blade and deck. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 23: Storage Of Battery
(at least every 3rd month), charge the battery 1 time per month at the normal operation time to make sure the battery keeps it full capacity. Incorrect storage can damage the battery and is not covered by warranty. BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 24: Maintenance
Fuel Lever Check and adjust when motor has cooled down Fuel tank Clean and replace if and filter necessary Fuel line Check and replace if necessary Carburetor Check (1) More often when used in dusty environments. BIGGER BOYZ TOYZ • BBTA.COM.AU... -
Page 25: Specification
Power supply Battery model number 6MF7A Battery production date / batch See top of battery Battery manufacturer Sichuan Liyang Industry Co.,Ltd Yanhuasi Industry Park, Anju District, Suining City, Sichuan, 401320, P.R. China Email address 415878203@qq.com BBTA.COM.AU • BIGGER BOYZ TOYZ... -
Page 26: Troubleshooting
Incorrect gap between the spark spark plug. plug and the electrode Check and adjust the spark plug The air filter is dirty or defective gap. Alternatively, replace the spark plug. Check the air filter for dirt and clean it. BIGGER BOYZ TOYZ • BBTA.COM.AU... - Page 27 Evaporation of fuel in the Check the air filter for dirt and carburettor clean it Loose throttle cable Wait a few minutes, and then try to start again Dirt in the carburettor Tighten the throttle cable Clean the carburettor BBTA.COM.AU • BIGGER BOYZ TOYZ...
- Page 28 BBTA.COM.AU Copyright © Bigger Boyz Toyz Australia Unit 2/3 Delta Place Albion Park Rail NSW 2527 • 02 4257 4787...
Need help?
Do you have a question about the BBT-LM-ER-26 and is the answer not in the manual?
Questions and answers