1. Manuals
  2. Brands
  3. Theralux Manuals
  4. Water Filtration Systems
  5. POOL+ MANAGER
  6. User manual

Theralux Pool+ Water Manager User Manual

Hide thumbs Also See for Pool+ Water Manager:

Advertisement

Table of Contents

User Manual
Pool+ Water Manager

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pool+ Water Manager and is the answer not in the manual?

Questions and answers

Related Manuals for Theralux Pool+ Water Manager

Summary of Contents for Theralux Pool+ Water Manager

  • Page 1 User Manual Pool+ Water Manager...
  • Page 2 Pools & Spas while the filtration pump is running. Once the pH and ORP levels have been set in the Theralux App, the Pool+ Water Manager will automatically dose Pool acid (when it is required) to maintain the set pH level. The Pool+ Water Manager will also maintain the systems ORP by either turning the Chlorinator On or Off, or by automatically dosing Chlorine if you prefer Liquid Chlorine or are utilising an Ioniser.
  • Page 3 • Ideally, as with all pool equipment, the controller should be installed out of direct weather. The service life of the Pool+ Water Manager will be longer if it is not exposed to direct sunlight and rain. • Before installing, and turning on the Pool+ Water Manager system, take a sample of your Pool/Spa water to a pool store and have it tested to ensure that the Pool/Spa system is properly balanced.

  • Page 4: Installation And Setup

    • A power cable providing power to the Pool+ Water Manager from a valve actuator port • A communication cable to connect the Pool+ Water Manager to either the Maser controller (if no Expansion Units are connected) or an Expansion Unit (if fitted).

  • Page 5: Installation

    INSTALLATION Do Not connect power to the Pool+ Water Manager until all the following criteria has been met. • Take a sample of your pool water to a pool shop, have it tested and have balanced your pool to the appropriate ranges as specified on pg1.
  • Page 6 • The pH and ORP probes have been plugged into the Pool+ Water Manager controller. (see diagram below) • The communication cable from the Pool+ Water Manager has been connected to either the Theralux Master Controller or the right-hand port in the last Expansion Unit. (see diagram below) BASE PLATE Comms cable from either the Aquatek or an Expansion unit.
  • Page 7  Lastly, connect the power cable from a valve actuator port (at the base of the Theralux Master Controller) to the Pool+ Water Manager (see Base Plate Diagram on page 5). As power is only been taken from the Valve Actuator output, the valve...

  • Page 8: Controller Connection

    Enter and the controller will exit you to the Installer Menu. 8. If you have Reset the Pool+ Water Manager or are setting it up for the first time you will use the ↑ or ↓ buttons to change from NO to YES and press Enter. After a few seconds of searching, the...

  • Page 9: App Setup

    If you not already completed the latest Firmware Update through the Theralux App, do so now to be able to continue further with the Chemical Setup. See pg 9 of the Theralux Quick Start Guide for instructions on how to complete the Firmware Update.
  • Page 10 Set Point to where you would like it to be. • You will also need to tap the button beside Acid Dosing to activate/de-activate the Acid Dosing Pump attached to the side of the Pool+ Water Manager controller. • The Acid Dosing button will generally be left On.
  • Page 11 APP FEATURES (CONTINUED)  Chemical Balance The other new menu option is Chemical Balance. (See the App Menu on page 7) • In this menu option you will be able to adjust your set levels for both pH and ORP. Both of these levels can be adjusted by either dragging the set point or by tapping along the Set Point line.
  • Page 12 APP FEATURES (CONTINUED)  Chemical Balance (continued) Once the Chemical Balance display window is expanded, the window displays the following. With the pH highlighted, the Chemical Balance window will display; 1. Whether the pH is Low, Normal, or High. 2. What the actual pH level is currently. 3.
  • Page 13 If your Pool/Spa systems water is not balanced correctly, you may see the following on the home screen of the App. What the Pool+ Water Manager is displaying is the following; 1. The pH reading is outside of the systems reading range of 5.5 to 8.5.
  • Page 14  Firmware Update At some point, a Firmware Update may become available for the Pool+ Water Manager. This update can be accessed through the Apps menu. You will need to open the App menu, tap on Device, then “View” next to Device Information.
  • Page 15 This depends on how large the Overdose (shock treatment) was. The Pool+ Water Manager will continue to operate normally during this time. • Dosing pump is not operating as it should - Check the following;...
  • Page 16 • Manual Overdosing of Chlorine (Shock Treatment) - Maintain ORP Set Point. It may take a period of days to weeks or the ORP reading to drop back to normal levels. This depends on how large the Overdose (shock treatment) was. The Pool+ Water Manager will not continue adding chlorine during this time period.
  • Page 17 Probe cleaning instructions pH Probe The cleanliness of the sensor and junction is critical for an accurate measurement. Drift (Offset) and a slow reading response are often due to an unclean sensor or junction. DO NOT use abrasive materials to clean the probe.
  • Page 18 INSTRUCTIONS FOR REPLACING THE SQUEEZE TUBE. The first thing that you will need to do is open the App Menu and go into Chemical Setup. When you are is the Setup menu you will need to turn the Acid Dosing button to the Off position. This will stop the peristaltic pump from operating while you are replacing the Squeeze Tube.
  • Page 19 App wil display either, <300 (check), >800 (check), or –-(check). The Pool+ Water Manager will be able to read a ORP range of 0 (little to no Chlorine) to 1000 (possibly over chlorinated) but any reading outside of the 300 to 800 range will only be displayed in the Chemical Setup option of the menu.
  • Page 20  If you are doing any work on the Pool+ Water Manager peristaltic pump , tubing, or probes, be sure to deactivate Acid Dosing (see Chemical Setup...

  • Page 21: Warranty

    • ORP & pH probes have a 12 month warranty at the discretion of the manufacturer. If the power cord is damaged, do not use the controller; return the unit to the supplier for repair. CUSTOMER RECORD (To be retained by the customer) DEALER/INSTALLER NAME SERIAL NUMBER DATE INSTALLED For service assistance visit www.theralux.com.au...
  • Page 22 Visit theralux.com.au or call Australia 1300 131 788 New Zealand +64 9 527 0753...

Table of Contents