1. Manuals
  2. Brands
  3. Gigo Manuals
  4. Toy
  5. SMART BRICKS CODING & ROBOTICS 7442-A
  6. Manual

Gigo SMART BRICKS CODING & ROBOTICS 7442-A Manual

Challenge pack 1
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
SMART BRICKS
# 7442-A
CODING
& ROBOTICS
8
4
93
+
MODELS
AGES
PIECES

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMART BRICKS CODING & ROBOTICS 7442-A and is the answer not in the manual?

Questions and answers

Related Manuals for Gigo SMART BRICKS CODING & ROBOTICS 7442-A

Summary of Contents for Gigo SMART BRICKS CODING & ROBOTICS 7442-A

  • Page 1 SMART BRICKS # 7442-A CODING & ROBOTICS MODELS AGES PIECES...

  • Page 2: Table Of Contents

    Important Information & Table of Contents Important Information & Table Dear Parents, Teachers, and of Contents . . . . . . . . . . . 1 Other Supervising Adults, Assembly Tips .

  • Page 3: Assembly Tips

    Assembly Tips PEGS AND CONNECTORS Take a careful look at the different assembly components. Blue short pegs, pink axles, blue 20mm axle connectors, and gray 30mm axle connectors all look pretty similar at first glance. When you assemble the models, it's important to use the right ones. CONNECTING FRAMES AND RODS Use the short pegs to connect frames and rods.

  • Page 4: Kit Contents

    Kit Contents What’s inside your experiment kit: Checklist: Find – Inspect – Check off Description Qty. Item No. Description Qty. Item No. B-SHORT PEG 7344-W10-C2B C-TRAPEZOID FRAME 7408-W10-A1Y C-AXLE 7026-W10-H1K C-TRAPEZOID COVER 7408-W10-B1Y C-20mm AXLE CONNECTOR 7413-W10-T1B C-MOTOR AXLE 7026-W10-L1S1 C-30mm AXLE CONNECTOR 7413-W10-U1S C-35mm AXLE II...
  • Page 5 Model Forklift PREPARATION STEP 2 STEP 1 Build this model and then complete the coding challenge on the next page. STEP 3 STEP 4 STEP 5 Use the robotic base unit from the base kit. ×2 STEP 8 STEP 7 STEP 6 CONTINUED .
  • Page 6 Forklift Model STEP 10 STEP 9 STEP OK You will also need a piece of paper raised up on a small stand. Forks Done CHALLENGE 1 LIFT THE CARGO Set up the map cards as shown. Place a piece Start with of paper on the card as the forks shown, with a small stand...
  • Page 7 Model Claw PREPARATION Build this model and then complete the coding challenge on page 8. Use the robotic base unit from the base kit.

  • Page 8: Claw

    Claw Model ×2 ×2...
  • Page 9 Model Claw Ball holder Done CHALLENGE 2 GRAB THE BALL Set up the map cards as shown. Place the ball in Place the ball Start with the the ball holder on the in the ball grabber arm holder . card as shown. pulled in (not extended as shown) .
  • Page 10 Catapult Model PREPARATION Build this model and then complete the coding challenge on page 11. Use the robotic base unit from the base kit.
  • Page 11 Model Catapult...

  • Page 12: Catapult

    Catapult Model Target basket Done CHALLENGE 3 SHOOT THE BALL Set up the map cards as shown. Place the Align the Start with the basket on the card as opening of catapult arm the basket so down (not up as shown.

  • Page 13: Walker

    Model Walker ×2 PREPARATION Build this model and then complete the coding challenge on the next page. ×2 ×2 Use the robotic base unit from the base kit. ×2...
  • Page 14 Walker Model Done CHALLENGE 4 WALK AROUND THE OBSTACLE Set up the map cards as shown. Place any Place an object object as an obstacle as an obstacle in on the card as shown. the path on the map card here . Create a program with the code cards to move the walker robot...

  • Page 15: Bulldozer

    Model Bulldozer PREPARATION Build this model and then complete the coding challenge on the next page. Use the robotic base unit from the base kit.
  • Page 16 Bulldozer Model ×2 ×2 Done Blade CHALLENGE 5 PUSH THE LOAD Set up the map cards as Start with the blade of the shown. Place some small bulldozer in the down position . objects to be pushed by Place some small the bulldozer on the map objects in the path of the bulldozer on the...

  • Page 17: Scissor Lift

    Model Scissor Lift PREPARATION Use the robotic Build this model and base unit then complete the from the coding challenge on the base kit. next page. ×2 ×2...
  • Page 18 Scissor Lift Model ×2 Done CHALLENGE 6 RAISE THE PLATFORM Set up the map cards as shown. Start with the scissor lift Create a program with platform lowered, not raised . the code cards to move the scissor lift robot from the Start card to the event map card A, where it will raise...

  • Page 19: Hammer

    Model Hammer PREPARATION Build this model and then complete the coding challenge on the next page. Use the robotic base unit from the base kit.
  • Page 20 Hammer Model Done CHALLENGE 7 HAMMER THE OBJECT Set up the map cards Place a small object for the as shown. Place a small hammer robot to object for the hammer hammer on the map card here . robot to hammer on the map card as shown.
  • Page 21 Model Plow PREPARATION ×2 Build this model and then complete the coding challenge on the next page. Use the robotic base unit from the base kit.

  • Page 22: Plow

    Plow Model Done CHALLENGE 8 PLOW THE FIELD Set up the map cards as Start with the blade of the plow in the down position . shown. Place some small, loose parts along the map Place some small objects in cards as shown.
  • Page 23 Solutions There are multiple solutions to each coding challenge. Here is an example of one correct solution for each challenge. Challenge 1: Lift the cargo Challenge 2: Grab the ball Challenge 3: Shoot the ball Challenge 4: Walk around the obstacle Challenge 5: Push the load Challenge 6: Raise the platform Challenge 7: Hammer the object...
  • Page 24 © 2020 Genius Toy Taiwan Co., Ltd. ALL RIGHTS RESERVED R21#7442-A-1...

Table of Contents