Hanna Instruments Checker HI713 Instruction Manual

Recommendations for Users
Before using this product, moke sure it is entirely suitable for your specific
opplicotion and for the environment in which it is used. Any variation introduced
by the user to the supplied equipment moy degrade the checker's performance.
For your and the checker's safety do not use or store it in hazardous environments.
Tips for on Accurate Measurement
●Ensure the somple does not contain any debris.
●Whenever the cuvette is ploced into the checker, it must be
dry outside and free of fingerprints, oil and dirt.
●Wipe the cuvette thoroughly with HI731318 microfiber
cleaning cloth or olint-free cloth prior to insertion.
●Shoking the cuvette can generate bubbles, cousing higher
tendings. To obtoin accurate meosurements, remove such
hubbies by swirling or by gently lapping the cuvelte.
●Do not let the reacted somple stand loo long ofter reagent
hos been odded, as occurocy will be effected.
●Discord the sample immediotely ofter the reoding hos been
taken or the gloss might become permanently stained.
Battery Replacement
To save the battery, the checker shuts down after 10 minutes of non-use and
2minutes ofter tending.
Afresh battery losis for ominimum of 5000 measurements. When the bottery is
drained, the instrument displays "bAd" then "bAt", and turns off.
To reploce the bottery, follow the next steps:
1. Press and hold the ON/OFF button to turn the checker off.
2. Turn the instrument upside down and use oscrewdriver to unfasten the screw ond
remove the battery cover.
Accessories
INSTRUCTION MANUAL
ReogenI Sets
HI713-25 Reagents fat 25 Phosphote Low Range tests
HI713
Phosphate Low Range
Other Accessories
Warranty
HI7I3 Checket*HC is warranted fat operiod of one yeor ogoinsl defects in
workmanship ond mnteriols when used for its intended purpose and maintained
occotding to instructions. This warranty is limited to repair or replacement free
of chorge. Dnmoge due to accidents, misuse, tempering or lock of prescribed
maintenonce is not covered. If service is required, contoct your local Honno
Instruments Office. If under warranty, report the model number, dote of purchose,
setiol number and the nature of the problem. If the repair is not covered by the
warranty, you will be notified of the chotges incurred. If the checker is to be
returned to Honno Instruments, first obtoin oReturned Goods Aulhorizolion (RGA)
number from the Technicol Service deportment and then send it with shipping
costs prepoid. When shipping ony product, moke sure it is properly packaged for
complete protection.
Hanna Instruments reserves the right to modify the design, construction, or
appearance of its products without advance notice.
HI713-11 Phosphate Low Range certified standard kit
Cuvette black cop far Checker® HC colorimeters (4 pcs.)
HI731225
HI731318 Cloth fat wiping cuvettes (4 pcs.)
Gloss cuvette and seal cap for Checker® HC colorimeters (4 pcs.)
HI731321
HI740028P 1.5V AAA bottery set (12 pcs.)
HI93703-50 Cuvette cleaning solution, 230 mL
p p m
n j !
n
Certification
All Honno Instruments conform to the CE European Directives.
Disposal of Electrical &Electronic Equipment, fhe product
should not be treated os household waste. Insteod hand it over
to the oppropriote collection point for the recycling of electricol RoHS
c o m p l i a n t
U .
C€
Phosphate
and electronic equipment which will conserve noturol resources.
Disposal of waste batteries. This product contoins batteries, do
not dispose of them with other household woste. Hand them over
to the oppropriote collection point for recycling.
Ensuring proper product and battery disposal prevents potentiol negative
consequences for the environment ond humon heolth. For more information,
contact your city, your local household waste disposol service, the ploce of
purchose or go to www.hannoinst.com.
All rights ore reserved. Reproduction in whole or in part is prohibited without the
written consent of the copyright owner, Hanna Instruments Inc, Woonsocket,
Rhode Island, 02895, USA.
3. Remove the old battery, replace it with onew 1.5V AAA bottery, inserting the
negative end first.
4. Reploce the bottery cover, fasten ond tighten the screw.
insfrumenfe
i s n i 3 0 9 / 2 0
1