Advertisement
Quick Links
Littfinski DatenTechnik (LDT)
•
Bühler electronic GmbH
HSI-88-USB
High Speed Interface for the s88-feedback bus and
from the Digital-Professional-Series !
HSI-88-USB-G
>> finished module in a case <<
Digital-Profi werden!
High Speed Interface-88
HSI-88-USB
Schnelles Computer-Interface für den s88 Rück-
meldebus. Ermöglicht drei s88 Rückmeldestränge.
LED1
GO
USB
ST1
This product is not a toy! Not suitable for children under 14 years. Improper use will imply danger or injuries due to
sharp edges and tips! Please store this instruction carefully.
•
Ulmenstraße 43
15370 Fredersdorf / Germany
Manual
the USB-Interface
Littfinski DatenTechnik (LDT)
www.ldt-infocenter.com
Littfinski DatenT echnik (LDT)
LED2
ST2
BOOSTER
STOP
ST6
EXT-PORT
•
Tel.: +49 (0) 33439 / 867-0
030913
Part-No.:
Transmits the feedback information
from the s88 bus via the digital central
unit directly to the PC without any
detour.
Fast galvanic separated connection to
the computer via the USB-interface
(1.1 / 2.0 Full-Speed).
•
3 Feedback-Lines will additionally
triple the reading speed of the
s88 feedback bus.
•
3 Feedback-Lines will offer as well
a simple arrangement of the
Feedback Modules below your
model layout base plate.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for LDT HSI-88-USB
Summary of Contents for LDT HSI-88-USB
- Page 1 Ermöglicht drei s88 Rückmeldestränge. • 3 Feedback-Lines will additionally triple the reading speed of the Littfinski DatenTechnik (LDT) www.ldt-infocenter.com s88 feedback bus. Littfinski DatenT echnik (LDT) LED1 LED2 • 3 Feedback-Lines will offer as well BOOSTER STOP a simple arrangement of the...
- Page 2 3. HSI-88-USB connection to the digital layout 4. HSI-88-USB implementing into your model railway software 5. Firmware Update 1. Preface / Safety Instruction: You have purchased the HSI-88-USB from the assortment of Littfinski DatenTechnik (LDT) for your model railway. Rückmelden Fahren und Schalten...
-
Page 3: Usb Driver Installation
USB of the HSI-88-USB. All other connections of the HSI-88-USB will remain without engagement. The red Light Emitting Diode of the HSI-88-USB will lighten up and on the PC-screen the info „Neue Hardware gefunden“ (“New hardware found”) will be shortly indicated. - Page 4 Manager) by clicking with the left mouse- key onto the Windows symbol (mostly at the left bottom) and select the device- manager. 2. If the HSI-88-USB has been connected to the PC via an USB-Interface two new devices will be identified at the Device- Manager.
- Page 5 HSI-88-USB – Manual 4. Select “Auf dem Computer nach Treibersoftware suchen” (“Searching for driver software on the computer”) (left picture). Now click onto the button „Durchsuchen...“ (“Searching”) (picture right). 5. Select the Download-Directory where you have saved the downloaded driver (at the sample: E:\ Windows10\64).
- Page 6 “Schließen” (“Close”). 9. Repeat the steps 3 to 8 for the second device “HSI-88-USB” (picture left). After successful installation you will find at the device manager a new device type “Modellbahnen” (“Model railways“) with the driver software for DiCoStation-USB and HSI-88-USB (picture right).
- Page 7 HSI-88-USB – Manual 3. HSI-88-USB connection to the digital layout: The HSI-88-USB will get the power supply via the 2-poles connection clamp KL1. 15 ...24V DC 14 ...18V AC For the supply can be 15 to 24 Volt DC or 14 to 18 Volt...
- Page 8 (picture left). Pay special attention that the bus-plugs will not be plugged to the pin bar in an offset position. Otherwise the s88-inputs of the HSI-88-USB will be damaged.
- Page 9 Middle until the end of the Right line. With the HSI-88-USB is it possible to control up to 31 16-fold-feedback modules (62 of the type RM-GB-8-N with 8 inputs). To each bus line can be a maximum of 31 modules connected.
-
Page 10: Firmware Update
HSI-88-USB – Manual 5. Firmware Update: The software of the HSI-88-USB is a so-called Firmware. This software can be easily actualized via the PC. 1. At first load-up the file “DiCoStation HSI- 88.exe” to your PC. This file can be found section “Downloads”... - Page 11 Important Information: The device number should never be changed. Otherwise the model railway software will not recognize the HSI-88-USB any more. The device number will be important as soon as you use more than one HSI-88-USB or additionally a DiCoStation for driving and switching. The first HSI-88-USB will get automatically always the device number 1.
- Page 12 ServiceTool “DiCoStation HSI- 88” with a click on the “X” at the right top window border. After this successful update you can use the HSI-88-USB as usual. Made in Europe by Littfinski DatenTechnik (LDT) Bühler electronic GmbH Ulmenstraße 43 15370 Fredersdorf / Germany Phone: +49 (0) 33439 / 867-0 Internet: www.ldt-infocenter.com...
Need help?
Do you have a question about the HSI-88-USB and is the answer not in the manual?
Questions and answers