L
D
T
ittfinski
aten
echnik
Operating Instruction
High Speed Interface
HSI-88 for the s88-
feedback bus
from the Digital-Professional-Series !
HSI-88-G
>> finished module in a case <<
Extremely fast (9600-baud) galvanic separated
⇒
connection through the serial port (RS232) of the
Personal Computer (PC).
3 feedback lines triple the reading speed of the s88
⇒
feedback bus.
3 feedback lines will also ease the grouping and
⇒
installation of the feedback modules below your
model railway panel.
This product is not a toy! Not suitable for children under 14 years of age! The kit
contains small parts, which should be kept away from children under 3! Improper
use will imply danger or injuring due to sharp edges and tips! Please store this
instruction carefully.
CE Part-No.:
24 02 66
Introduction / Safety Information:
You have purchased the High Speed Interface HSI-88 for the s88
feedback bus. The HSI-88 is a high quality product, which is
supplied within the
Digital-Professional-Series
DatenTechnik (LDT).
We wish you having a good time using this product.
• Please read the following instructions carefully. Warranty will
expire due to damages caused by disregarding the operating
instructions. LDT will also not be liable for any consequential
damages caused by improper use or installation.
The finished modules in a case come with 24 month warranty.
Connecting the Interface to your digital
control center and Personal Computer
(PC):
• Attention: Please switch off your model railway by
disconnecting the transformers from AC-current, and
switch off your PC before starting the installation of the
unit.
Voltage (14 to 18V AC from any model railroad transformer) will
be supplied via clamp KL1 to the interface HSI-88.
If you use the HSI-88 on a 3L system (Märklin tracks with center
conductor) you can use feedback modules which switch to
ground connection.
In this case please pay special attention to the correct
connection of the supply cables "brown" (system ground)
and "yellow".
(LDT)
030313
Part-No.:
of Littfinski
The input of clamp KL1 is marked accordingly.
If your model railway software supports the HSI-88 you need a
second free serial port on your PC. This port will be mostly
indicated as COM-Port.
Use the supplied computer cable to connect the Interface HSI-
88 via the free serial port with your PC.
Digital-Profi werden!
High Speed Interface-88
HSI-88
Schnelles Computer-Interface für den s88-Rück-
meldebus. Ermöglicht 3 Rückmeldestränge.
High Speed Interface 88
HSI-88
Rev. 2.1
Littfinski DatenT echnik
At last connect the s88-feedback modules to the HSI-88 Interface
by using the three 6-pole pin plugs marked LEFT, MIDDLE and
RIGHT.
With the HSI-88 you can build up 3 feedback lines. This will give
the advantage of speeding up the reading of the feedback
modules by three times.
Another advantage is the simple arrangement and installation of
your feedback modules below your model railway track panel.
High Speed Interface 88
HSI-88
Rev. 2.1
Littfinski DatenTechnik
Start always with connecting the first line on the input marked
as LEFT of the HSI-88. If you want to build a second line connect
it to the input marked as MIDDLE. A third line must be connected
to the input marked as RIGHT accordingly.
Even if you use only some few feedback modules on your model
railway track it is recommended to distribute the feedback
modules to all three inputs (LEFT, MIDDLE, and RIGHT) of the
HSI-88 evenly.
As a result, the feedback-information will be much faster
detected by the HSI-88 and transferred to the PC.
Littfinski DatenTechnik (LDT)
www.ldt-infocenter.com
Computer
RS232
LM2574
Computer
RS232
Need help?
Do you have a question about the HSI-88-G and is the answer not in the manual?
Questions and answers