Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for holzkraft KSO 1500
Summary of Contents for holzkraft KSO 1500
- Page 1 Instruction Manual Edge milling machine KSO 1500 KSO 1500...
-
Page 2: Table Of Contents
12.1 Spare parts drawing........17 tion of its content is not permitted without explicit 13 EC-Declaration of Conformity....18 consent. Infringements will lead to claims for damages. 14 Notes............19 Subject to technical modifications and changes. KSO 1500 | Version 2.10... -
Page 3: Introduction
We are always interested in valuable experience and cates potentially hazardous situations which may knowledge gained from using the application, which-then cause death or serious injury if not averted. could be shared and be valuable to develop our-products even further. KSO 1500 | Version 2.10... -
Page 4: Intended Use
CE conformity of the grinder and are prohi- bited. The company Stürmer Maschinen GmbH assu- mes no liability for design and technical changes to the edge grinding machine. KSO 1500 | Version 2.10... -
Page 5: Qualification Of The Staff
Manufacturer: Certain work may only be carried out by specialist per- sonnel of the manufacturer. Other personnel are not au- thorized to carry out this work. To carry out the work, contact our customer service. KSO 1500 | Version 2.10... -
Page 6: Technical Data
Observe the accident prevention regulations issued by your Employers Liability Insurance Association or other competent supervisory authority, responsible for your company. Fasten the loads properly. Fig. 1: Type plate KSO 1500 KSO 1500 | Version 2.10... -
Page 7: Packaging
Step 1: Secure the work table with the table safety lever. ment. Step 2: Attach 2 cables to the crane hook and to the cor- responding points of the device (see Fig. 2). Step 3: Carefully lift and transport the device with the crane. KSO 1500 | Version 2.10... -
Page 8: Description
K100 537 2310 2270 x 150 mm K120 537 2312 2270 x 150 mm K150 537 2315 2270 x 150 mm K180 537 2318 2270 x 150 mm K220 537 2322 Fig. 4: Extraction units KSO 1500 | Version 2.10... -
Page 9: Set Up
- a cable cross-section of at least 1.5 mm² is used for the Fig. 5: Mount side table supply cable, -the direction of rotation of the motor is correct (see ar- row on the motor). KSO 1500 | Version 2.10... -
Page 10: Mount Or Change The Sanding Belt
Step 1: Disconnect the machine from the mains. Step 2: Press the lever H (Fig. 10) under the table to the left. Fig. 8: Quick clamping device for sanding belt rollers Fig. 10: Table adjustment laterally KSO 1500 | Version 2.10... -
Page 11: Angle Adjustment Of The Sanding Belt
7.8 Assembly of the grinding sleeves Fig. 13: Abrasive sleeve mounting and height adjustment of the table Step 1: Disconnect the machine from the mains. Step 2: Open the cover (1, Fig. 12) and fasten in the spe- cified position. KSO 1500 | Version 2.10... -
Page 12: Adjusting The Sanding Belt Alignment
Use protective boots! Wear protective clothes! The edge sanding machine can be operated from two positions (see Fig. 15). Position A: Workpieces of rectangular and square shape can be machined from this position. KSO 1500 | Version 2.10... -
Page 13: Grinding Edges
Maintenance and repair work may only be carried out by qualified personnel. If the edge milling machine does not work properly, con- tact a dealer or our customer service. The contact details can be found in chapter 1.2 Customer Service. KSO 1500 | Version 2.10... -
Page 14: Functional Check
Then apply a thin layer of oil or grease to the moving parts. Lubricate the slide rails with grease. KSO 1500 | Version 2.10... -
Page 15: Troubleshooting
If necessary, ask for the product-specific data sheets. Step 2: If necessary, dismantle the device into manage- able and usable assemblies and components. Step 3: Guide the device components and operating ma- terials to the appropriate disposal routes. KSO 1500 | Version 2.10... -
Page 16: Disposal Via Municipal Collection Points
The symbol on the product or its packaging indi- cates that this product should not be treated as normal The sanding belt for the edge milling machine KSO 1500 household waste, but must be returned to a collection must be ordered. The sanding belt has the number 122 point for the recycling of electrical and electronic equip- in the spare parts drawing 1. -
Page 17: Spare Parts Drawing
The following drawing should help you in case of service to identify necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorized dealer. Fig. 17: Spare parts drawing KSO 1500 KSO 1500 | Version 2.10... -
Page 18: Ec-Declaration Of Conformity
Part 1: General requirements (IEC 60204-1:2005) DIN EN ISO 12100: 2011-03 Safety of machinery - General principles for design - Risk assessment and risk reduction Responsible for documentation: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 04.05.2021 ______________________ Kilian Stürmer Manager KSO 1500 | Version 2.10... -
Page 19: Notes
Notes 14 Notes KSO 1500 | Version 2.10... - Page 20 www.holzkraft.de...
Need help?
Do you have a question about the KSO 1500 and is the answer not in the manual?
Questions and answers