holzkraft KSO 150 F BASIC Instruction Manual
  1. Manuals
  2. Brands
  3. holzkraft Manuals
  4. Power Tool
  5. KSO 150 F BASIC
  6. Instruction manual

holzkraft KSO 150 F BASIC Instruction Manual

Edge milling machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Instruction Manual
Edge milling machine
KSO 150 F BASIC
KSO 150 F BASIC

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KSO 150 F BASIC and is the answer not in the manual?

Questions and answers

Related Manuals for holzkraft KSO 150 F BASIC

Summary of Contents for holzkraft KSO 150 F BASIC

  • Page 1 Instruction Manual Edge milling machine KSO 150 F BASIC KSO 150 F BASIC...

  • Page 2: Table Of Contents

    Forwarding and reproduction of this do- cument as well as use and notification of its content is not permitted without explicit consent. Infringements will lead to claims for damages. Subject to technical modifications and changes. KSO 150 F BASIC | Version 1.04...

  • Page 3: Introduction

    KSO 150 F BASIC | Version 1.04...

  • Page 4: Responsibility Of The Operator

    Said risk as- operating instructions and operators have explicitly en- sessment shall be reflected in operating instructi- trusted operating staff with the task. ons for machine operation. KSO 150 F BASIC | Version 1.04...

  • Page 5: Personal Protective Equipment

    Protective gloves are intended to protect the hands instructions. from components with sharp objects as well as fric- tion, abrasion, and deep-cut injuries. - Never work under the influence of concentration-di- sturbing illnesses, fatigue, drugs, alcohol or medi- cines. KSO 150 F BASIC | Version 1.04...

  • Page 6: Intended Use

    - Never remove mechanical or electrical safety de- vices. - Special attention is needed during transport or re- construction; The transport regulations must be followed. - Only use original spare parts and accessories to avoid possible danger and accident risks. KSO 150 F BASIC | Version 1.04...

  • Page 7: Technical Data

    1230 mm Weight 290 kg Supply voltage 400 V Sanding belt length 3000 mm Fig. 2: Type plate KSO 150 F BASIC Sanding belt width 150 mm Transport, Packaging, storage Circumferential belt speed(s) 20 m/s Sanding surface length 1050 mm 5.1 Delivery and Transport...

  • Page 8: Packaging

    Transport with a forklift / pallet truck: ment. The edge sanding machine can be transported with a forklift or pallet truck if it is firmly mounted on a pallet. KSO 150 F BASIC | Version 1.04...

  • Page 9: Description Of The Device

    - Graphite coating - Miter Step 2: Connect pre-assembled suction hoses to the ex- traction system and secure. - Operating manual Step 3: Perform a functional test of the suction power. KSO 150 F BASIC | Version 1.04...

  • Page 10: Mount Or Change The Sanding Belt

    Step 2: Use the height adjustment handwheel to crank is coasting. the worktable to the desired height. Step 3: Tighten the table safety lever again. Fig. 5: Change motor direction of rotation KSO 150 F BASIC | Version 1.04...

  • Page 11: Operation

    Step 6: Reposition the worktable as close as possible to the sanding belt. Step 7: Adjust the sanding stops left and right to the desi- Wear protective clothes! red depth with the screws. Wear a dust mask! KSO 150 F BASIC | Version 1.04...

  • Page 12: Care, Maintenance And Repair

    50 operating hours at the latest. ment must be reinstalled immediately. Carefully clean the guides with a soft brush and turpen- Replace damaged safety equipment immediately! tine or other suitable and non-hazardous diluents. KSO 150 F BASIC | Version 1.04...

  • Page 13: Disposal, Recycling Of Old Devices

    Step 2: If necessary, dismantle the device into manage- able and usable assemblies and components. Step 3: Guide the device components and operating ma- terials to the appropriate disposal routes. KSO 150 F BASIC | Version 1.04...

  • Page 14: Troubleshooting

    The contact details are in - Item number: 5363150 chapter 1.2 Customer Service.Specify the following key - Drawing number: 2 data when ordering spare parts: - Position number: 1 KSO 150 F BASIC | Version 1.04...

  • Page 15: Spare Parts Drawings

    The following drawings should help you in case of service to identify necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorized dealer. Spare parts drawing 1 Fig. 7: Spare parts drawing 1 KSO 150 F BASIC | Version 1.04...
  • Page 16 Spare parts Spare parts drawing 2 Fig. 8: Spare parts drawing 2 KSO 150 F BASIC | Version 1.04...
  • Page 17 Spare parts Spare parts drawing 3 Abb. 9: Spare parts drawing 3 KSO 150 F BASIC | Version 1.04...
  • Page 18 Spare parts Spare parts drawing 4 Fig. 10: Spare parts drawing 4 KSO 150 F BASIC | Version 1.04...
  • Page 19 Spare parts Spare parts drawing 5 Fig. 11: Spare parts drawing 5 KSO 150 F BASIC | Version 1.04...
  • Page 20 Spare parts Spare parts drawing 6 Fig. 12: Spare parts drawing 6 KSO 150 F BASIC | Version 1.04...
  • Page 21 Spare parts Spare parts drawing 7 Fig. 13: Spare parts drawing 7 KSO 150 F BASIC | Version 1.04...
  • Page 22 Spare parts Spare parts drawing 8 Fig. 14: Spare parts drawing 8 KSO 150 F BASIC | Version 1.04...
  • Page 23 Spare parts Spare parts drawing 9 Fig. 15: Spare parts drawing 9 Spare parts drawing 10 Fig. 16: Spare parts drawing 10 KSO 150 F BASIC | Version 1.04...

  • Page 24: Electric Wiring Diagram Kso 150 F

    Electric wiring diagram KSO 150 F 13 Electric wiring diagram KSO 150 F Fig. 17: Electric wiring diagram KSO 150 F KSO 150 F BASIC | Version 1.04...

  • Page 25: Ec - Declaration Of Conformity

    <= 16 A per phase and not subject to conditional connection Responsible for documentation: Kilian Stürmer, Stürmer Maschinen GmbH, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 20.08.2019 ______________________ Kilian Stürmer Manager KSO 150 F BASIC | Version 1.04...
  • Page 26 www.holzkraft.de...

Table of Contents