Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Filser Electronic ATR600
Summary of Contents for Filser Electronic ATR600
- Page 1 ATR600 P/N 600-(0XX)-(0XX) P/N 600-(1XX)-(1XX) VHF Communication Transceiver Installation and Operation Dokument-Nr.: 03.1301.010.71e Revision: 1.03 Date: 04.06.2007 Filser Electronic GmbH • Gewerbestraße 2 • 86875 Waal phone: 08246 / 96 99-0 • fax: 08246 / 10 49 • web: www.filser.de...
-
Page 2: List Of Changes
ATR600 Installation and Operation List of Changes Revision Date Description of Change 1.00 13.02.2007 Initial Version ”Installation and Operation“ 1.01 02.03.2007 ”remote“ not displayed. 1.02 02.04.2007 microphones/headphones: parallel connection 1.03 04.06.2007 MIC setting completed List of Service-Bulletins (SB) Service Bulletins have to be inserted into this manual and to be enlisted in the following table. -
Page 3: Table Of Contents
ATR600 Installation and Operation CONTENTS GENERAL..................5 Symbols ..................5 Customer Support...............5 Survey of Variants...............5 Introduction .................6 Features..................6 Telecommunication Data ............6 Technical Data ................7 Environmental Conditions ............9 Scope of Delivery..............10 1.10 Accessories ................10 INSTALLATION ................12 Unpacking................. 12 Requirements ................12 Antenna .................. - Page 4 ATR600 Installation and Operation 4.5.4 DATA – Select from Frequency Database ......24 Database Download..............25 Status and Error Messages............25 REMOTE CONTROL ..............26 CONTROLS/DISPLAY ..............27 Dokument-Nr.: 03.1301.010.71e / Revision: 1.03...
-
Page 5: General
ATR600 Installation and Operation 1 GENERAL 1.1 Symbols Instructions whose non-observance can cause damage to the device or other parts of the equipment. Supplementary information. 1.2 Customer Support For fastest handling of reshipments please use the reshipment form available from our homepage www.filser.de. -
Page 6: Introduction
ATR600 Installation and Operation 1.4 Introduction This manual contains information about the physical, mechanical and electrical characteristics and about installation and operation of the VHF Transceiver ATR600. 1.5 Features • VHF communication transceiver for aircraft installation • operating range: 118.000 .. 136.975 MHz •... -
Page 7: Technical Data
ATR600 Installation and Operation 1.7 Technical Data COMPLIANCE JTSO-2C37e, ED-23B Class 4 JTSO-2C38e, ED-23B Class C TSO-C37d, RTCA DO-186A Class 4 TSO-C38d, RTCA DO-186A Class C LBA.O.10.911/106 JTSO APPLICABLE REQUIREMENTS EUROCAE ED-23B RTCA DO-160D RTCA DO-178B Software Level D DIMENSIONS height: 65 mm (2.56 in) - Page 8 ATR600 Installation and Operation TRANSMITTER POWER OUTPUT 6 W (nominal) 4 W (minimal) HARMONIC DISTORTION < 10 % at 70 % modulation SIDETONE OUTPUT 100 mW into 300 Ω (headphone) MICROPHONE standard microphone (Elektret, 50 mV .. 2 V), 100 mVRMS connectable to MIC 1 or MIC 2...
-
Page 9: Environmental Conditions
ATR600 Installation and Operation 1.8 Environmental Conditions Characteristic DO–160D Section Cat. Condition Temperature / Altitude Low ground survival temperature 4.5.1 – 55°C Low operating temperature 4.5.1 – 20°C High ground survival Temperature 4.5.2 + 85°C High Short-time Operating 4.5.2 + 70°C... -
Page 10: Scope Of Delivery
(4 pcs) 1.10 Accessories Accessories ATR600 Order No. Description BSKS600B ATR600 cable loom with free ends for gliders BSKS600E ATR600 cable loom for airplanes consisting of BSKS600F and BSKSZUB BSKS600F ATR600 cable loom with free ends for airplanes without connector set... - Page 11 ATR600 Installation and Operation Remote Control Order No. Description ZATR600RT remote control incl. cables and EASA Form 1 BSKS60RT complete cable loom consisting of BSKS600R1 and BSKS600R2 BSKS600R1 cable loom for remote control (power supply) BSKS600R2 cable loom for remote control (data cable) Antennas for Planes Order No.
-
Page 12: Installation
For storage or reshipment the original packaging should be used. 2.2 Requirements • The installation of the ATR600 depends on the conditions in the airplane. In arrangement with an aeronautical-engineering enterprise, location and kind of the installation are specified. • Leave sufficient area for the installation of cables and connecting plugs. -
Page 13: Antenna
ATR600 Installation and Operation 2.3 Antenna For the ATR600 a conventional vertically polarized VHF COM antenna with a 50 Ohm impedance is needed. Wideband comm antennas provide efficient operation over the comm band. Antennas should be installed in accordance with the manufacturer recommendations. -
Page 14: Microphone Connection
ATR600 Installation and Operation 2.4.2 Microphone Connection Microphone inputs: MIC 1: for dynamic (factory setting) or standard microphones; switchable with “Mic Switch“ on the right side of the equipment MIC 2: (only) for standard microphones; adjustable microphone level The input for standard microphones is appropriate for input voltages of 50 mVpp to 2 Vpp. -
Page 15: Display Illumination
ATR600 Installation and Operation 2.4.4 Display Illumination Equipment depending differences for connecting LIGHT (Pin 4, brown cable) P/N 600-(0XX)-(0XX) • not connected: illumination auto-adjusted • connected to GND: illumination off P/N 600-(1XX)-(1XX) • LIGHT is not connected from the plug into the equipment. -
Page 16: Wiring Double-Seater With Intercom (Bsks600S/T)
ATR600 Installation and Operation 2.4.6 Wiring Double-Seater with Intercom (BSKS600S/T) Consider chapter 2.4.4 Display Illumination! Cable loom “BSKS600T“ includes the second PTT key. Dokument-Nr.: 03.1301.010.71e / Revision: 1.03... -
Page 17: Microphone Settings
ATR600 Installation and Operation 2.5 Microphone Settings 2.5.1 Basics MIC- und VOX-values are essential for intercom. Using VOX the loudness threshold is adjusted so that ambient noise is not transmitted to the headphones, but an additional signal caused by speaking will start intercom. -
Page 18: Checkup After Installation
ATR600 Installation and Operation 2.6 Checkup after Installation When installation is completed all steering and control functions of the aircraft are to be examined, in order to exclude disturbances by the wiring. Subsequently, check antenna matching. Insert a standing wave meter, respectively a direction-sensitive RF power meter into the antenna line. -
Page 19: Drawings
ATR600 Installation and Operation 3 DRAWINGS Equipment Dimensions Power/RS232 ATR600 Antenna 65 mm Ø 57 mm 168 mm 18 mm 20mm Equipment Connectors Panel Cut-out 57,5 mm 4 x Ø 6,5 mm 47,0 mm Dokument-Nr.: 03.1301.010.71e / Revision: 1.03... -
Page 20: Operation
ATR600 Installation and Operation 4 OPERATION 4.1 ON/OFF • power on: press about 0.5 s • power off: press about 3 s Display after power on: ATR600 VERS.1-1 DataBase 16.03.2001 • equipment type • software release • frequency database (if loaded) 4.2 INIT-Menu –... -
Page 21: Vol, Sq, Vox, Dim
ATR600 Installation and Operation 4.3 VOL, SQ, VOX, DIM 4.3.1 Setting Mode After power on “VOL“ (volume) is active. Select setting mode: press (repeatedly) SEL The mode switches back to “VOL” after 5 s without manipulation or by selecting another frequency. -
Page 22: Vox - Intercom Threshold
ATR600 Installation and Operation 4.3.4 VOX – Intercom Threshold Display: “VOXnn“, nn = 01 .. 10 Turn “VOL“ to adjust VOX to avoid transmission of ambient noise in the cockpit. Only an additional voice signal causes start of the intercom connection. -
Page 23: Frequency Setting
ATR600 Installation and Operation 4.5 Frequency Setting 4.5.1 General Input options: • direct input with the MHz/kHz controls • select from the USER list with the MEM control • select from the frequency database in the “DATA” Mode Run through functions by pressing MODE. -
Page 24: Data - Select From Frequency Database
ATR600 Installation and Operation Store Frequencies The stand-by frequency shown in the lower line can be named and saved in the USER list. Before saving, the designated memory location has to be selected with MEM in direct input mode, because when... -
Page 25: Database Download
ATR600 Installation and Operation 4.6 Database Download To download a database connect a PC to the RS232 port of the ATR600. The connection cable is available from Filser GmbH. Database and required software are available on www.filser.de. Display after start of transfer software:... -
Page 26: Remote Control
ATR600 Installation and Operation 5 REMOTE CONTROL In tandem cockpits operation can be performed using a remote control from the second panel. The remote control has to be connected to the RS232 port of the ATR600. Frequency, volume, squelch and VOX can be adjusted. -
Page 27: Controls/Display
ATR600 Installation and Operation 6 CONTROLS/DISPLAY Rotary Knobs 1: MEM select frequency from user list adjust volume, squelch, VOX, 2: VOL illumination adjust MHz 3: MHz select characters when assigning a name adjust kHz 4: kHz set cursor position when...
Need help?
Do you have a question about the ATR600 and is the answer not in the manual?
Questions and answers