Hotron SSS-5 User Manual

MP-10413 MP-10413 '24.06
Safety Sensor for Swing Doors
We would like to thank you for purchasing this product. Before using, please read the following instructions carefully.
User Manual (Original)
WARNING WARNING
Disregarding this symbol may result in
! ! !
serious injury or death
Special attention is required when this
Note Note
symbol is shown
1 General Description / Features
The SSS-5 is a microprocessor controlled active infrared presence detector for swing doors.
- 6 detection spots per PCB unit provide a wide detection area.
- The detection distance to the floor is set automatically by pressing a Push Switch.
- The detection range can be adjusted manually, using dip switches in increments of 50mm
- The relay output can be changed from NO to NC using a dip switch.
- Self diagnostic and monitoring functions are implemented.
2 Components
The illustration below shows the standard configuration of SSS-5L1 with one PCB units.
Screw
Side Cover-L
Filter Cover
Joint
PCB unit Assembly
PCB unit
PCB Holder
Screw
Angle Stabilizer
Table.1 Information of SSS-5
Model Length Filter
(1)
Joint (3)
name [mm] Cover
SSS-5S1 360 1 0 2
SSS-5M1 692 2 1 3 (2)
SSS-5L1 1023 3 2 3
3 Mounting and Wiring Information
3.1. Notice
CAUTION CAUTION
! ! ! Before mounting this sensor please note the following remarks.
Note Note
1 2
Do not mount the Do not mount the
sensor higher than sensor where rain or
2.8 [m] 2.8 [m]
2.8 [m]( 9' 2" ). snow will fall directly
on the unit.
5
4
The Aluminum
Ensure no condensation
Case(s) should be
gets onto the sensor.
located close to the
Leading edge of the
door to maximise
safety detection.
6
Be careful not to drop the sensor, during transportation and installation. It
WARNING WARNING
! ! !
3.2 Mounting Hole
Drill fixing holes as illustrated below.
When installing the SSS-5 on both sides
of the door it may be necessary to drill a
wiring hole through the door. (Ref. 3.6
Plan View of SSS-5 Installation)
3.3 Mounting the Aluminum Case
1
Unscrew the Side Covers and remove the Filter Cover.
Hold the cable when
removing the side cover
3
Remove the PCB Unit.
Loosen the Screw on the PCB Holder and slide it aside to remove the PCB
Unit.
3.4 Replacing the PCB unit(s)
CAUTION CAUTION
! ! ! When replacing the PCB unit it is very important that the side with "LEADING EDGE" marked on it is inserted
so that it is closest to the leading edge of the door. This will ensure maximum
1
Remove the Terminal Block from the PCB unit.
2 Insert the PCB unit into the Aluminum Case, making sure that the side
marked "LEADING EDGE" is closest to the leading edge of the door.
Attach the Angle Stabilizer and tighten the screws on the PCB Holders.
Hinge
LEADING EDGE MARK
PCB unit
Disregarding this symbol may result in
CAUTION CAUTION
! ! !
injury or damage to equipment
Setting required to conform
EN16005 EN16005
with EN16005
Aluminum Case
Side Cover-R
PCB unit
Front view of PCB unit
Slide SW Push SW
Dip SW Operation LED
Terminal Block
Accessories
Mounting
(3) (5)
Installation Jamb Hole Cover
Screws
Instruction
4×16 [mm]
(4)
Wire Sheath
600 [mm]
Communication Cable
3
Ensure the minimum
of reflected sunlight
from the floor.
Leading edge Leading edge
Hinge Hinge
Hinge Hinge
<Top view> <Top view>
may cause the sensor to break.
Drilling may cause Electric shock! When drilling, pay attention to hidden wires.
Unit : [mm]
200 200 200
2-φ3.5 Holes for Screw 2-φ3.5 Holes for Screw
SSS-5S1
280 280 280 280 280 280
SSS-5M1
390 390 390
SSS-5L1
2
Remove Angle Stabilizer.
1)Lift and slide the Angle Stabilizer to the side as indicated.
2)Push the Angle Stabilizer with your thumb to remove it
from the Aluminum Case.
1) 2)
4
Fix the Aluminum Case to the door with Screws.
at the door edge.
pedestrian safety
LEADING EDGE
MARK
LEADING EDGE MARK
PCB unit
Hinge
SSS-5
3.5 Wiring to the door controller
Install the Jamb Hole Cover and Wire Sheath when wiring to the door controller.
Drill following holes.
30
CAUTION CAUTION
! ! !
Connect the wires to the
door controller using the
Terminal Block
Wire size
Screw 0.15 to 3.5 [mm
3.6.1 Option 1: Plan View of SSS-5 Installation
(PCB units on both sides of the door wired back to the Door Controller independently)
Extra Wire Hole through the door
Hinge
Door Controller
A/B
Mounting
Jamb Hole Cover
Screws
3.6.2 Option 2: Plan View of SSS-5 Installation
3×10 [mm]
(PCB units connected using Communication Cable and only 1 PCB units is wired back to the
Door Controller)
Hinge
Door Controller
Jamb Hole Cover
4 Dip Switch Settings
Leading edge Leading edge
In order to prevent dangerous door movement
! !
please configure sensor Dip-SW settings
WARNING WARNING
before supplying power to the sensor.
4.1 TEST Input
When connected to a door controller without a
TEST input, set to "A". When connected to a
door controller with a TEST input, set to "B"
before wiring.
1 1 2 2 3 4 5 6 7 8 3 4 5 6 7 8
Refer to [6.Timing Chart of events] .
Set to "B" to comply with EN16005
EN16005 EN16005
4.2 Optical Interference
3-φ3.5
When two SSS-5's are installed in close proximity ,
optical cross interference between SSS-5's might cause
mis-operation. To avoid this , different frequency
1 1 2 2 3 4 5 6 7 8 3 4 5 6 7 8
3-φ3.5
390 390 390 settings should be selected using DIP Switch #2.
4.3 Relay Output Mode
Refer to [6. Timing chart of events]
for full details on Relay Output Mode.
1 1 2 2 3 4 5 6 7 8 3 4 5 6 7 8
4.4 Masking detecting spots
1 1 2 2 3 4 5 6 7 8 3 4 5 6 7 8
4.5 Detection Range
1 1 2 2 3 4 5 6 7 8 3 4 5 6 7 8
Set Non-Detection
distance A A
EN16005 EN16005
Check that the detection
range conforms to EN16005
torque
0.5 Nm
5 Detection Angle Adjustment
The detection angle can be adjusted between 5 ～25 [deg] in 5 [deg] increments using the Angle Stabilizer.
Example) Changing angle from 5゜to 25゜
1. 2.
(3)Rotate PCB unit
(2)Slide (1)Lift
10゜ 10゜
5゜ 5゜
EN16005 EN16005 Check that the detection area position conforms to EN16005
SSS-5S1
English
SSS-5M1
SSS-5L1
Clamp the Wire Sheath between the Jamb Hole Cover A/B
φ10 φ10
Wires to
Wiring Hole the controller
3 - φ2.6
Jamb Hole
Screw Holes
Cover A
Unit : [mm]
Wire Sheath
1
2
7 7
3
4
1 1
5
2
]
6
7
Wire Sheath PLAN VIEW and Wiring
PCB units are connected to each other
using the Communication Cable (supplied)
Hole(φ10) drilled through the door.
Connector 6P
Note: Remember to set the Slide SW as indicated
= Default Setting
B
A
1
A
4 5
spots
4
6 5 3 2 1
4 5
spots
- 5 4 3 2 1
50mm 250mm
6 7 8 6 7 8
100mm 300mm
8 8
6 7 6 7
150mm 400mm
6 7 8 6 7 8
200mm 500mm
6 7 8 6 7 8
3.
(4)Slide Back
Side View
Angle Stabilizer
15゜ 15゜
20゜ 20゜
25゜ 25゜
COMPLIED STANDARDS
EN 12978:2003 +A1:2009
EN16005:2012 +AC:2015
DIN18650-1:2010
EN ISO 13849-1:2015
EC type examination
44 205 13738001
Screw (3×10 [mm])
Jamb Hole
Cover B
Power supply ( AC/DC 12～24[V] )
Relay Output ( Common )
Relay Output1
Relay Output 2(Another PCB Unit Output)
TEST Input ( - )
TEST Input ( + )
「OFF｣ PCB Unit2
7P Terminal stand
Leading
Edge
「OFF｣ PCB Unit1 PCB Unit1
7P Terminal stand 7P Terminal stand
「ON｣
Slide SW PCB Unit2
7P Terminal stand
（Unused）
Leading
Edge
「OFF｣
PCB Unit1 PCB Unit1
7P Terminal stand 7P Terminal stand
PCB unit
With TEST
Without TEST Without TEST
B
0v
A
0v
SSS-5
SSS-5 B
2 2
NO NC
3 3
4 5
spots
4
- - 3 2 1
4 5
spots
- - - 3 2 1
Detection
A
Non-Detection
PCB unit
25゜
5゜ 5゜