Hotron 3H-IR14 User Manual

Motion and presence sensor

Advertisement

Quick Links

Motion and Presence Sensor
We would like to extend our thanks to you for purchasing this product.
User Manual
Before using this product, please read the following instructions carefully.
Please retain this manual for reference in case it needs to be referred to during the lifetime of this product.
The symbols below indicate an extremely dangerous situation.
Disregarding this symbol may result in
WARNING
serious injury or death
The symbols below indicate what should be obeyed.
This symbol refers to an
This symbol refers to a Caution
instructions which is prohibited

1. DESCRIPTION

Cover
Body
Connector
Potentiometer
Dip Switch
(Sensitivity Volume)
LED Indicator
Area Mask
Detection Window

2. MOUNTING PRECAUTIONS

CAUTION
To prevent leakage, malfunction or damage, please follow instructions below.
1. Mount lower than 3m (9.8ft)
2. Ensure no moving objects in the
detection area
3.0m
4. Mount where rain or snow will not fall directly on unit.
If the sensor is exposed to
excessive rain or snow install
with a Hotron weather cover
In the following cases, the sensor may detect without the presence of a person
1. Accumulation of
2. Environment is
snow or water on the
humid or steamy.
floor.
3H-IR14
Disregarding this symbol may result in injury
CAUTION
or damage to equipment
This symbol refer to an Instruction which must
be followed
Accessories
Mounting Screws
(2 pcs.)
Base
3. Ensure the minimum of reflected
sunlight from the floor
5. Please install in a place where no vibration
3. Objects placed in the detection area.
4. Pets / Animals enter the detection area.
3. MOUNTING & WIRING INFORMATION
Drilling may cause electric shock.
WARNING
Be careful of hidden wires inside the door engine cover.
1. Determine the mounting
position of the device and
attach Mounting Template.
Drill mounting and wiring
holes.
4. Install Base with Mounting
Screws.
7. Set the following parameters

4. DIP SWITCH SETTINGS

8. VERIFICATION OF OPERATION

Cable
(2.5m)
4. DIP SWITCH SETTINGS
Mounting
CAUTION
Please set in a manner suitable for operation.
Template
User
1
2
Manual
Presence
Quantity of
Timer
Detection Rows
R4
2s
R3
30s
R2
60s
R1
1 2
3 4
If you change the setting of the Dip switch when
the power is on, the sensor will be reset in
approx 6 s.
The reset is the same as the Power-On.

5. APPLYING POWER

CAUTION
Before turning on the power, please wire the door controller to the sensor.
If there is a moving object in detection area after power-up / reset, the sensor will be in motion detection mode.
If there is no moving object in detection area after power-up / reset, the sensor will be in presence detection mode.
Power-on/
Reset
If you carry out the followings, please turn off the power.
If you carry out the followings when the power is turned on, the sensor will detect for the presence timer setting that you have set
Place or remove the
mat on the detection
area.
2. Remove Cover
6. Wiring to the door controller.
5. Attach Body to Base.
8. House Connectors in the
space provided.
Quantity of Detection Rows
Default Setting
The number of rows of detection can be set to 4, 3, 2,1 depending on
3
4
5
6
7
8
detection area requirements.
Presence Timer
Monitor
Self-
Frequency
Monitoring
Mode
The sensor will detect a stationary object only for the time set by the
Presence Timer. When it is set to
A
Normal
OFF
and 2nd row, 2 s in case of the 3rd and 4th row.
Snow
ON
B
Frequency
7
8
C
When more than two sensors are used in close proximity to each other,
select different frequency setting for each sensors to prevent interference.
D
( A + B + C + D = Maximum 4 sensors )
5 6
Monitor Mode
Set to Snow in instances where false door activations can result from
blowing snow, leaves or rubbish close to the door detection area. It should
be noted that sensitivity to detecting pedestrians may also be reduced.
Self-Monitoring
When the sensor has malfunctioned, the Green/Red LED blinks alternately
and the relay output is relayed to the sensor.
7 s
No moving object
2 s
Presence detection
Motion
Detection
Moving object
Motion detection
Adjust the angle of Body.
Adjust the width of the detection area.
3. Remove Mounting Screws and Body
from Base .
Cable
Connector
Green N.C.
Yellow N.O.
White COM
Red Black Power
Non Pole
9. Place Cover on sensor and clean the sensor.
Do not move Body when
attaching Cover.
, the period is
in case of the 1st
7 s
Remove
No moving object
moving
Presence detection
object
Adjust the sensitivity.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 3H-IR14 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Hotron 3H-IR14

  • Page 1 If there is no moving object in detection area after power-up / reset, the sensor will be in presence detection mode. If the sensor is exposed to excessive rain or snow install No moving object with a Hotron weather cover Presence detection Power-on/ Motion...
  • Page 2 Green/Red LED blinks . 12 s 60 s 12 s HOTRON CO.,LTD. Hotron Ireland Ltd. In this case, please replace the sensor immediately. OFF / ON of Self- 1-11-26 Hyakunin-Cho, Shinjuku-Ku, Tokyo, Japan 26 Dublin Street (2nd Floor), Carlow, Ireland Make...

Table of Contents