Preparation For Use; Turning On Unit For The First Time; To Add Or Delete Channels - Toshiba SDV398 Owner's Manual

Preparation for Use

Turning on Unit for the First Time

Please note: most instructions in this man-
VCR VCR
ual refer to remote control use.
Be sure your TV's input is set to VIDEO. (Name may
1
vary with TV manufacturer. See your TV manual for
details.)
2 Select your on-screen language.
Then press [B] to continue.
or
3 Press [B] to start Auto Set Up.
Do you connect the cable from the cable box or the satellite box to the unit's
ANT-IN jack?
Yes
Press [SETUP] to exit.
• Refer to "Connecting to a Cable / Satellite Box" section on page 12.
No
Please wait for a few minutes.
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[CH. / K // L ] (or [CHANNEL /
• If "AUTO SET UP" appears on the TV screen again, check the cable con-
nections. Then, press [B] once again.
Note:
• Repeat these steps only if either there was a power failure or this unit
has been unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by using [the Number buttons] or [CH. K / L].
Notes for using [the Number buttons]:
• When selecting cable channels which are higher than 99, enter channel
numbers as a three-digit number. (for example: 117, press [1], [1], [7])
• You must precede single-digit channel numbers with a zero. (for exam-
ple: 02, 03, 04 and so on)
E8EB6CD_SD-V398KC_EN_v1.indd 13 E8EB6CD_SD-V398KC_EN_v1.indd 13
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
PUSH B
CH 01
AUTO SET UP
YES NO
After scanning...
]).

To Add or Delete Channels

1 Press [SETUP] to select "CHANNEL SET UP".
Then press [B] to go to next step.
• If the clock is not set, the "CLOCK SET" menu appears when you
press [SETUP]. In this case, press [SETUP] again.
2 Select "MANUAL SET UP".
Then press [B] to go to next step.
or
3 Select the channel to be added or deleted.
or or
4 Select "ADD" or "DELETE".
5 To exit the menu.
To Preset the Channel Again
1) Press [SETUP] until the main menu appears.
2) Select "CHANNEL SET UP" by using [ K / L ], then press [B].
3) Select "AUTO SET UP" by using [ K / L ], then press [B]. After scanning, the
tuner stops on the lowest memorized channel.
To Change the Selected On-screen Language
1 Press [SETUP] until the main menu appears.
Select "LANGUAGE SELECT".
2
Then press [ B ] to go to next step.
or
3 Select "ENGLISH", "FRANCAIS" or
"ESPAÑOL". Then press [SETUP].
or
Note:
• If you accidentally select Spanish or French and need English:
Press [SETUP] and choose "SELEC. IDIOMA" or "SELECTION LANGUE".
Press [B] and select "ENGLISH". Finally, press [SETUP].
• To add or delete channels in this unit, [CH. K / L ] button works on the channel
number memorized in this unit, [ K / L ] works on all.
– 13 –
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
B CHANNEL SET UP
CLOCK SET
or
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
CHANNEL SET UP
AUTO SET UP
B MANUAL SET UP
MANUAL SET UP
CHANNEL 30
ADD
or
MANUAL SET UP
CHANNEL 30
DELETE
or
- M E N U -
B TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
- M E N U -
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
CLOCK SET
B LANGUAGE SELECT
AUDIO OUT
TV STEREO [ON]
SAP
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
2009/01/29 17:05:11 2009/01/29 17:05:11
(CATV)
(CATV)
[ON]
EN