superbrightleds EZ Series Instructional Sheet

Important: Read all instructions prior to installation.
Wireless LED Tunable White Wall Switch for EZ
Dimmer Series Controllers
Parts Included
1 - 868MHz LED Dimmer Wall Switch
1 - 3V CR2032 Battery with Tray
Wall Switch
Turns light on/off. If the Controller Pairing Switch has been depressed,
Single Press
a single dial press on the Wall Panel Switch pairs the Switch to the Controller.
Double Press Alternates between color temperature mode and dimming mode.
During color temperature mode, scrolls through cool white (dial left) to natural
Left/Right Rotate
white (middle) to warm white (dial right). During dimming mode, controls LED intensity level.
Increases LEDs to maximum intensity. Dial down to set max brightness for color temperature mode.
Hold Press
1. On/Off/Color Temperature/Brightness Push Dial 1
Push dial for remotely activating/controlling light strips.
2. Color Gradient
2
Visual key representing specific dial colors, from cool white (dial left) to warm
white (dial right).
3. Dimming Level
3
Visual key representing the dial brightness level.
Controller
1. Pairing Switch
4
To pair Wall Switch to Controller, press the Controller Pairing Switch once and
then press Wall Switch dial. Lights will blink once to indicate pairing. To unpair Wall
Switch(es), press and hold Controller Pairing Switch until lights blink twice.
2. Master/Slave Jumper
5
Set Jumper to Master for main Controller. Master emits syncronization signal to
Slave Controllers. Set Jumper to Slave to receive syncronization signal from Master
Controller. Use Master for the first Controller in each zone. To achieve precise
syncronization between Controllers in one zone, set additional Controllers to slave.
Wall Switch Installation Steps
1. Pull off dial and collar from front plate.
2. Using a flat head screwdriver, pry rear switch housing away from
front plate.
3. Insert battery with tray into slot, matching the polarity on the
battery with the slot labels.
4. Fasten wall switch using mounting screws.
5. Reinstall front plate, collar and dial.
Battery Safety
• Remove and immediately recycle or dispose of used batteries according to local regulations and keep
away from children. Do NOT dispose of batteries in household trash or incinerate.
• Even used batteries may cause severe injury or death.
• Call a local poison control center for treatment information.
• Non-rechargeable batteries are not to be recharged.
• Do not force discharge, recharge, disassemble, heat above (manufacturer's specified temperature rating)
or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
• Ensure the batteries are installed correctly according to polarity (+ and -).
• Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or
rechargeable batteries.
• Remove and immediately recycle or dispose of batteries from equipment not used for an extended period
of time according to local regulations.
• Always completely secure the battery compartment. If the battery compartment does not close securely,
stop using the product, remove the batteries, and keep them away from children.
2 - Mounting Screws
Rev Date: V2 02/14/2025
4400 Earth City Expy, St. Louis, MO 63045
Instructional Sheet
4
5
MASTER
EZD-VCT-WM
3
2
1
Push ON/OFF
Safety
• DO NOT install with power applied to Controller.
• DO NOT expose the Wall Switch or Controller to moisture.
Set-Up Instructions
Wall Switch
1. Follow illustrated steps below to remove the Battery Tray. Insert the
3V battery included with the Wall Switch.
Controller
1. Make sure power to the Controller is disconnected.
2. Using a small flathead screwdriver, loosen the labeled terminal screws
visible on the top of the Controller.
3. Matching light strip wires with labeled slots on the Controller, insert
wires and tighten terminal screws. Be sure wire conductor, not wire
insulation, is secured in terminal.
4. Turn power on and wait until light strip illuminates. If it does not come
on, check light strips and wiring connections.
1 2
Part Number:
EZD-VCT-WM
Controller: EZD-4C8A
EZD-4C8A Controller
V+ V+
EZD-4C8A Easy Dimmer Series
PRI:
V- CH1
Uin=12-36VDC
lin=8.3A
SEC: CH2
Pairing
Uout=1x(12-36)VDC
Switch
Iout=4x8A
CH3
Pout=1x(96-288)W
TEMP RANGE: -20ºC-+50ºC
CH4
SLAVE
EZD-VCT-WM Wall Switch
Operating Voltage 3 VDC
Battery Size CR2032
Operating Frequency 868 MHz
FCC ID# 2ACUQ2836
EZD-4C8A Controller
Input Voltage Current Output Wattage
12~36 VDC 4 X 8A 384W(12V) 768W(24V)
1152W(36V)
3
866-590-3533 superbrightleds.com
4