HP dx2200 Illustrated Parts Map page 2

System Board Connectors and Jumpers (position of some untitled components may vary in location)
ATX1 Main power
AUD1 Front audio
BATTERY RTC battery
CPU FAN Processor fan
DIMM1 Memory module 1
DIMM2 Memory module 2
FDD1 Diskette drive
IDE1 Optical drive
JCD1 CD audio
JCMOS CMOS
JPFP1 Front power switch/LED
JPW1 CPU main power
CMOS
Jumper
Status Setting Notes
Normal 2-3 Default
Clear 1-2 leave on for 5 seconds
System Hardware Interrupts
IRQ System Function
0 Timer Interrupt
1 Keyboard
2 Interrupt Controller Cascade
3 Serial Port (COM B)
4 Serial Port (COM A)
5 Unused, available for PCI
6 Diskette Drive
7 Parallel Port (LPT 1)
JUSB1 Front USB
JUSB2 Internal USB for media reader
PCIE16X1 PCIe X16
PCIE1X1 PCIe X1
PCI1 PCI slot 1
PCI2 PCI slot 2
SATA1 SATA primary
SATA2 SATA secondary
SPKR speaker
SYSFAN1 Chassis fan
U4 Processor
IRQ System Function
8 Real-Time Clock
9 Unused
10 Unused, available for PCI
11 Unused, available for PCI
12 Mouse
13 Coprocessor
14 Primary ATA (IDE) Controller
15 Secondary ATA (IDE) Controller
Clearing CMOS
The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS
memory using by performing the following procedure:
Ä
CAUTION: The power cord must be disconnected from the power source before changing the jumper
setting. (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board
1. Turn off the computer and any external devices, then disconnect the power cord from the power outlet.
2. Remove the access panel.
3. Locate jumper CMOS and move the jumper from pins 2-3 to pins 1-2.
4. Leave the jumper on pins 1-2 for 5 seconds.
5. Move the jumper back to pins 2-3.
6. Replace the access panel.
7. Connect the power cord to the power outlet.
8. Turn on the computer, allow it to start.
Diagnostic LEDs
LED Color LED Activity
Power Green On
Power Green 1 blink every 2 seconds
Power Green 1 blink every 2 seconds
Power Clear Off
Power Green Glows for 3 seconds followed by
a 1 second pause.
Power Green 1 blink every second for 5
seconds, then 2 second pause.
5 beeps.
Power Green 1 blink every second for 6
seconds, then 2 second pause.
6 beeps.
None None No LED but rapidly inclining
beeps
None None No LED but rapidly declining
beeps
Hard Drive Green Blinking
Computer Setup (F10) Utility Features (not all features may be available)
Product Name
SKU Number
Processor Type
Processor speed
CPU ID/Patch ID
Cache Size
System
Memory Size
Information
System ROM
Integrated MAC Address
UUID
System Serial Number
Asset Tracking Number
Asset Tag Number
Set Date
Set Time
PATA Controller
PATA Channel 0 Master
PATA Channel 0 Slave
Standard CMOS
SATA Controller
Features SATA Channel 1 Master
SATA Channel 2 Master
Floppy Drive Controller
Drive A
Halt On
POST Delay
Device Boot Disabling
F9 Boot Menu
Removable Device Boot Priority
Hard Disk Boot Sequence
Optical Drive Boot Sequence
Network Boot Sequence
First through Fourth Boot Devices
Advanced BIOS
Boot Up NumLock Status
Features
Security Option
APIC Mode
MPS Version Control for OS
BIOS Write Protection
Execute disable bit
Enhanced Intel SpeedStep Technology
Hyper-Threading Technology
UMA Frame Buffer
Advanced
Init Display First (VGA Setting)
Chipset Features Surroundview
AutoDetect PCI CLK (VGA Setting)
Onboard HD Audio
OnChip USB Controller
USB Legacy Support
Onboard LAN
Integrated
Onboard LAN Boot ROM
Peripherals
Onboard Serial Port
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
After AC Power Loss
ACPI Suspend type
Power
External Modem S5 Wake-up
Management
RTC Alarm Resume
Setup
Date (of Month) Alarm
Resume Time (hh:mm:ss)
Reset Configuration Data
PnP/PCI
Resources Controlled By
Configuration IRQ Resources
Maximum Payload Size
System Fan Fail Check
Smart Fan Function
Current CPU Temperature
Current System Temperature
Current CPU Fan Speed
Current System Fan Speed
PC Health Status
Vcore
+12V
VCC5
+3.3V
VBAT (V)
3VSB (V)
Load Optimized
Defaults
Set Supervisor
Password
Set User
Password
Save & Exit Setup
Exit Without
Saving
Note: See Computer Setup (F10) Utility Guide on the Documentation Library CD.
State/Message
Computer on
(S1) Normal Suspend Mode
(S3) Suspend to RAM
(S5) Computer off
CPU thermal shutdown
No memory installed or improperly installed
(pre-video memory error)
Graphics card error (pre-video graphics error)
Incorrect system password.
Correct system password.
Hard drive activity