LIVOLTEK ACE/-S Business Quick Installation Manual

ACE/-S BusinessAC Charger
Scan the QR code to
view more information
Preparation Tools
Φ6
Electric drill Rubber hammer
Goggles Anti-dust mask
Multimeter Hot air gun
Wall Mounting
IV
①
Step 1: Take out the
bracket, choose the
appropriate mounting
height (between 0.5m -
1.5m) and mark four
points on the wall.
②
Step2: Drill 4 mounting holes (6X35 mm) and
insert the 4 expansion pipes ( Φ 6X28 mm) into
the holes.
③
Step3: Lock 4
$T3.9x27 tapping
screws into the
upperexpanslon pipe.
Notice: The above installation steps apply to both connector charger and socket charger.
VI
Grid cable prepare
①
Step 1:Prepare the wire stripper to strip the cable.
85mm
Models
8mm
A0070230E1EY
A0070230E1SY
Stripping cable for single-phase chager
85mm
8mm Models
A0110400E1EY
A0220400E1EY
A0110400E1SY
A0220400E1SY
Stripping cable for three-phase chager
②
Step 2: Heat shrinkable tube to make the cable more professional.
40mm
10mm
PH2 2mm
Cross screwdriver Slotted screwdriver
Round terminal
crimping pliers Wire stripper
Cable clamp (RJ45) Marker
Hang up
④
Step4: Hook the
charger to the bracket
via the included
bracket.
Press
⑤
Step5: After hanging the charger on the bracket, tighten
the left and right knobs in a clockwise direction.
Type Power cable Outer diameter range Stripping length
7kW-connector
2
3*6mm 13~18mm
85mm/8mm
7kW-socket
Type Power cable Outer diameter range Stripping length
2
11kW-connector 5*2.5mm
2
22kW-connector 5*6mm
13~18mm 85mm/8mm
2
11kW-socket 5*2.5mm
2
22kW-socket 5*6mm
-Heat shrinkable tube: 40mm;
-Outer extension: 10mm;
Charger-socket or connnector *1
Insulated terminal
* 4(1P)/6(3P)
USE R MA N UAL
Electric vehicle AC charger
Copyright
Any part of this manual, including text, pictures, graphics, etc., belongs to Hangzhou
Livoltek Power Co., Ltd. Without written permission, no unit or individual may extract,
copy, translate or modify all or part of this manual in any way.
V.01
User manual * 1
Notice: The above installation precautions apply to both connector charger and socket charger.
V
① Step 1: After determining the installation position
of the charger and cable alignment, make sure
the cable in the center of the charger bracket
according to the column mounting hole diagram,
and drill 3 mounting holes(12 X 120 mm) on the
concrete base.
Notice: the height of the cement base shall ensure that the
lowest point of the vehicle connector when stored shall be
135
located at a height between 0.5m and 1.5m above ground
level when the charger is installed on the column.
③
Step 3: Loosen the
5 screws on the
hook, take down
the hook, pass the
③
②
cable of the
①
cement base
through the inside
of the column and
lead out from the
cable outlet of the
column.
Wire Prepare
③
Step 3: Use the tool to crimp insulated
terminal
crimp terminal for single-phase chager
crimp terminal for three-phase chager
Packing Lists
Expansion pipe * 4
Charging Card
Charging Card * 2
Bracket* 1
Quick Installation Guide
AC EV Charger for Socket Type Series
Quick installation
Certicate * 1
guide *1
Mounting Place
Column Mounting
②
Step 2: Install three
M8x100 expansion bolts
into the mounting holes
and fasten the expansion
bolts to ensure that the
exposed height of the
expansion bolts is
between 15 ~ 25mm.
④
Step 4: Lift the bottom ⑤ Step 5: Thread the hook
cover, align the column through the cable and
with the installation holes tighten the 5 screws.
of the cement base one by
one, and then tighten the
⑥
Step 6: Refer to the
three M8x100 expansion
bolts. above steps "3, 4 and
5" of "Wall mounted
installation" to complete
the installation of the
bottom shell and
column.
Network cable prepare
Use cable clamp to follow the below order of the cable to make the
RJ45 connecter. Network cable: EIA/TIA 568B standard.
crimp the connector
strip the cables
1-White with orange stripes
2-Orange
1 2 3 4 5 6 7 8
3-White with green stripes
4-Blue
5-White with blue stripes
6-Green
7-White with brown stripes
8-Brown
Tapping screw * 4
L-type Hexagon
Wrench *1