Advertisement
Quick Links
User's manual
Customer Service
US: 1-800-645-2986
WARNING
IMPACT HAZARD!
Moving parts can crush and cut. Raise work surface before
removing the monitor. Failure to heed this warning may result
in serious personal injury or property damage!
WARNING
TIPPING HAZARD!
For carts without an internal
power system, a CPU should
be mounted to the cart before
displays are mounted. DO NOT
remove CPU while displays are
mounted because personal injury
or equipment damage may occur.
WARNING
TO MOVE CART:
. 1
o L
w
e
t r
e h
i d
lowest position.
2. Disconnect any power cords.
3. Stow cords to keep out of the way.
. 4
U
n
o l
k c
c
s a
e t
direction of travel.
5
P .
s u
t h
e h
c
t r a
using the hand holds.
WARNING
This component is under high tension, and can cause injury
or damage if release bolt Is removed before assembly. This
release bolt should only be removed after assembly is
complete. Please refer to manual.
1-800-645-1232
Manual del usuario
Servicio de atención al Cliente
México: 01.800.681.6940
OPP Medical cart
Model 290898
p s
a l
t y
t o
e h
s r
a
d n
i p
o v
t t
t o
e h
o r f
m
t
e h
s
d i
s e
1
Manuel de I'utilisateur
Service à la clientèle
Canada: 888-645-2986
Advertisement
Related Manuals for Global Industrial 290898
Summary of Contents for Global Industrial 290898
- Page 1 Service à la clientèle México: 01.800.681.6940 Canada: 888-645-2986 US: 1-800-645-2986 OPP Medical cart Model 290898 WARNING IMPACT HAZARD! Moving parts can crush and cut. Raise work surface before removing the monitor. Failure to heed this warning may result in serious personal injury or property damage!
- Page 2 Mobile Sit and Stand Workstation WARNING WARNING This warning alerts you to the possibilities of serious injury It is the installer's responsibility to make sure the combined or death if you do not follow the following instructions. It is weight of all components does not exceed weight capacity the installer's responsibility to make sure all components of 50Kg (110 lbs).
-
Page 3: Installation
Mobile Sit and Stand Workstation Installation Attaching the Lift Pole Note: This step may require assistance. 1. Do not remove the gas spring tension screw below the label before completing the assembly. Put lift pole on the base Note: Install four round head hex screws M6 x15mm each with a washer through mounting holes in the base and into lift pole with a 5 mm allen wrench... - Page 4 Mobile Sit and Stand Workstation Attaching Keyboard Tray Slot 2. Put keyboard tray slot on the lift pole. Install four round head hex screws M6 x15mm through mounting holes on the keyboard tray slot and finally into lift pole with a 5 mm allen wrench so that the keyboard tray slot is firmly attached to the lift pole.
- Page 5 Mobile Sit and Stand Workstation Mouse Holder Installation 4. Insert mouse holder on the side of keyboard tray slot from top to bottom. Attaching Work Surface 5. Put the work surface over the keyboard tray slot. Install four phillips screws M6 x 12mm through mounting holes on the keyboard tray slot and finally into work surface using long shaft phillips magnetic screwdriver until it is firmly attached to...
- Page 6 Mobile Sit and Stand Workstation All labels must be on the same side as the label at the base. Remove gas spring tension retaining screw Mobile Base After final assembly, remove the gas spring tension retaining screws as shown in Fig. (A) and (B) below. Pull the lever up to change the work surface to desired height.
- Page 7 Mobile Sit and Stand Workstation Specifications ・ Model: 290898 ・ Work surface height: 892mm-1292mm (35"- 51") ・ Work surface dimensions: 560mm (L) x 430mm ( W) (22" x 17") ・ Keyboard tray dimensions: 450mm (L) x 200mm (W) (18" x 8") ・...
-
Page 8: Features And Components
Mobile Sit and Stand Workstation FEATURES AND COMPONENTS Work surface with handles Mouse holder Hideaway keyboard tray Vertical adjustment lever (lift lever to adjust) Lift pole Pedal locking casters Metal base...
Need help?
Do you have a question about the 290898 and is the answer not in the manual?
Questions and answers