Ameriwood HOME 4335306COM Manual
  1. Manuals
  2. Brands
  3. Ameriwood HOME Manuals
  4. Indoor Furnishing
  5. 4335306COM
  6. Manual
Ameriwood HOME 4335306COM Manual

Ameriwood HOME 4335306COM Manual

Queen wall bed
Hide thumbs

Advertisement

Table of Contents

4335306COM (Federal White)
4335356COM (Monterey Oak)
Queen Wall Bed
Date of Purchase ___ / ___ / ___
Lot Number:
Do Not Return This Product!
Contact our customer service team for help first.
Call: 1-800-489-3351 (toll free)
Visit: www.dorelhome.com
to view the limited warranty valid
in the U.S. and Canada.
THIS INSTRUCTION BOOKLET CONTAINS WARNINGS AND
PRODUCT SAFETY INFORMATION. DO NOT PROCEED WITHOUT
REVIEWING THOUROUGHLY. FOR ANY QUESTIONS, CONTACT
CUSTOMER SERVICE.
Difficulty Meter
Easy
B344335000COMS0
Professional
(see page 2)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4335306COM and is the answer not in the manual?

Questions and answers

Related Manuals for Ameriwood HOME 4335306COM

Summary of Contents for Ameriwood HOME 4335306COM

  • Page 1 4335306COM (Federal White) 4335356COM (Monterey Oak) Queen Wall Bed B344335000COMS0 Date of Purchase ___ / ___ / ___ Lot Number: THIS INSTRUCTION BOOKLET CONTAINS WARNINGS AND PRODUCT SAFETY INFORMATION. DO NOT PROCEED WITHOUT REVIEWING THOUROUGHLY. FOR ANY QUESTIONS, CONTACT CUSTOMER SERVICE.
  • Page 2 Part 1 - Installation • Installation steps will require the use of one professional and one other person to assist. • The second person must be able to lift wall bed components and hold them in position while the professional installs hardware.

  • Page 3: Before You Start

    Before You Start Read through each step carefully and follow the proper order. Separate and count all your parts and hardware before attempting assembly. Parts are labeled on the surface or edge of the part Open your item in an area you plan to keep it. Give yourself enough room for the installation and assembly process.

  • Page 4: Board Identification

    Board Identification Not actual size dorelhome.com...
  • Page 5 Board Identification parts for 4335356COM (Monterey Oak) parts for 4335306COM (Federal White) Parts List Parts List PART PART ITEM QTY DESCRIPTION ITEM DESCRIPTION NUMBER NUMBER 34335306010 LEFT PANEL 34335356010 LEFT PANEL 34335306020 RIGHT PANEL 34335356020 RIGHT PANEL 34335306030 TOP 34335356030...

  • Page 6: Part List

    WARNING! CHOKING HAZARD - Hardware bag contains small parts. Keep out of reach of children. Part List Note that your unit may Actual Size contain extra hardware (x26) (x8) (x26) (x8) #A22610 #A13950 #A15520 #A22620 cam bolt #8x3-1/2" pan head #14 x 1/2"...
  • Page 7 WARNING! CHOKING HAZARD - Hardware bag contains small parts. Keep out of reach of children. Part List Note that your unit may Actual Size contain extra hardware (x13) (x2) (x1) #A53470 #A81090 #A99860 bracket wire saddle stud finder Not Actual Size shown on pages 31 &...
  • Page 8 Bed Frame Identification Not Actual Size Note: Not all parts will be identified. Mattress Holder (2) Right Assembly Left Assembly 9632096-19c 9632096-19d 9632096-19a 9632096-19b Right Pivot Arm Wood Slat (30) Plastic Cap (60) Left Pivot Arm Gas Piston (4) U-Bracket (4) 9632096-19f 9632096-19e 9632096-19g...

  • Page 9: Part 1 - Installation

    Part 1 - Installation Installation steps will require the use of one professional and one other person to assist. Installation steps will cover pages 10-35. Professional is required for: • all hardware fastening steps • identifying wall structure and appropriate attachment hardware to use •...
  • Page 10 STEP 1 (x5) (x6) (x4) (x1) Proper orientation of Cam Lock Proper orientation of Cam Lock Press in face connector (13) into the holes in the Upper Back Panel (E) then engage the other end of the face connectors (13) into the holes in the Top Rear Rail (N). Press the two parts together to lock together. Please note: the parts will be loose in the holes until you press both parts together.
  • Page 11 STEP 2 (x4) (x8) Proper orientation of Cam Lock Proper orientation of Cam Lock dorelhome.com...
  • Page 12 STEP 3 (x6) (x8) (x3) Proper orientation of Connector Proper orientation of Cam Lock Proper orientation of Cam Lock dorelhome.com...
  • Page 13 STEP 4 (x2) (x4) Proper orientation of Cam Lock Proper orientation of Cam Lock dorelhome.com...
  • Page 14 STEP 5 (x4) (x3) Proper orientation of Connector dorelhome.com...
  • Page 15 STEP 6 (x3) (x4) dorelhome.com...
  • Page 16 STEP 7 (x4) (x3) dorelhome.com...
  • Page 17 STEP 8 (x1) dorelhome.com...
  • Page 18 STEP 9 (x3) (x13) Press in face connector (13) into the holes in the Left Panel (A). Then engage the other end of the face connectors (13) into the holes in the Left Side Rail (L). Press the two parts together to lock together. Please note: the parts will be loose in the holes until you press both parts together.
  • Page 19 STEP 10 (x1) (x8) The Left Pivot Arm (19e) is located in the 9632096COM Wall Bed Mechanism box dorelhome.com...
  • Page 20 STEP 11 (x3) (x13) Press in face connector (13) into the holes in the Right Panel (B). Then engage the other end of the face connectors (13) into the holes in the Right Side Rail (M). Press the two parts together to lock together. Please note: the parts will be loose in the holes until you press both parts together.
  • Page 21 STEP 12 (x1) (x8) The Right Pivot Arm (19f) is located in the 9632096COM Wall Bed Mechanism box dorelhome.com...
  • Page 22 STEP 13 turn clockwise to lock in place dorelhome.com...
  • Page 23 STEP 14 turn clockwise to lock in place unfinished surface dorelhome.com...
  • Page 24 STEP 15 First, assemble Upper Back Panel (E) to Left Panel (A). Then, assemble one of the Center Back Panels (F) to Left Panel (A). LOCK UNLOCK Please note: Top Rear Rail (N) is assembled on finished surface of Upper Back Panel (E). unfinished surface dorelhome.com...
  • Page 25 STEP 16 dorelhome.com...
  • Page 26 STEP 17 LOCK UNLOCK unfinished surface dorelhome.com...
  • Page 27 STEP 18 LOCK UNLOCK unfinished surface dorelhome.com...
  • Page 28 STEP 19 LOCK UNLOCK dorelhome.com...
  • Page 29 STEP 20 LOCK UNLOCK dorelhome.com...
  • Page 30 STEP 21 (x4) (x4) Carefully, lay the unit onto its front. Tap in the Bushings (7) with a hammer and then screw in the Glides (6) all the way. dorelhome.com...
  • Page 31 STEP 22 The next steps are to assemble your electrical hardware Cord length information: 1. The power supply cord is 72” from transformer to the plug's tip 2. The loop wire for the sensor disk, from the transformer is 48” to the center of the loop 3.
  • Page 32 STEP 22 continued LED Light Kit Assembly Open the package for the LED Light Kit. Everything will be assembled together. First, unclip the LED Light from the Light Plug as shown... unclip light plug LED light Second, you must disassemble the LED Light. Unscrew the cover off the base and then remove the lens piece.
  • Page 33 STEP 23 (x2) (x1) (x1) Place transformer (24a) on the Headboard Panel (H) in the location shown. Use screw (14) to attach transformer (24a). Thread the power supply plug (24b) in front of the Bottom Stringer (I) if needed for power source. dorelhome.com...
  • Page 34 STEP 24 With the help of another person, carefully stand the unit upright. During these steps, allow another person to securely hold the unit from tipping over. Place touch sensor disk (25) in location shown in Lower Shelf (J). (x1) dorelhome.com...
  • Page 35 STEP 25 (x1) (x1) (x1) With the help of another person holding the unit steady upright, take the Loop Sensor (24c) that is connected to the Transformer (24a) and place underneath the Lower Shelf (J) at the hole location of the Touch Sensor Disk (25). Thread screw (15) through the Loop Sensor and screw into Touch Sensor Disk (25).
  • Page 36 The next steps are to attach your unit to the wall. Wall attachment steps will cover pages 37-45. The following steps are required to be completed by a professional. The second person may assist by holding the cabinet in position while the professional completes alignment, leveling and installation steps.
  • Page 37 STEP 26 Carefully, place the unit FLUSH against the wall There are notches provided at the back of your unit. These notches are to fit around the baseboard on your wall. If your baseboard is higher or thicker than the notches provided on the unit, you will need to remove the baseboard, cut it down to fit on both sides of your unit, then...
  • Page 38 STEP 27 Using a level, be sure the unit is square (height, width, and depth) to function properly A ladder will be required. Do not lean against the top of the unit, it may cause sagging If required, unscrew the Glides counterclockwise as necessary in all 4 corners until your unit is...
  • Page 39 What type of wall do you have? For Steps 28 & 29 you will need to choose between two types of screws to use based on the type of wall you are installing this product to. Wooden & Metal Studs - Follow Steps 28 & 29 - Wooden &...
  • Page 40 STEP 28 - Wooden & Metal Studs Locate at least 3 DIFFERENT studs, in the horizontal direction, but 4 is better. Locate the studs in the wall, Average distance between studs (16") using a stud finder. Wall Studs Using a pencil, mark the stud locations on the upper surface of the Upper Back Panel (E) where the...
  • Page 41 STEP 29 - Wooden & Metal Studs (x8) (x8) First, make sure that your unit is still level in all directions. As shown in the view to the right, fasten the unit to the wall studs with screw (3) and washer (26).
  • Page 42 STEP 29 continued... Example of 4 screws being placed horizontally in wall studs on part E and part I. Please note this is just an example - all wall stud distances are different. dorelhome.com...
  • Page 43 STEP 28 - Concrete Choose 4 horizontal predrilled holes equally across the Upper Back Panel (E). Carry and use the same predrilled holes down to the Bottom Stringer (I). Using a pencil, mark the locations on the upper surface of the Upper Back Panel (E) where the predrilled holes are provided.
  • Page 44 STEP 29 - Concrete (x8) (x8) First, make sure that your unit is still level in all directions. As shown in the view to the right, fasten the unit to the concrete wall with screw (28) and washer (26). The view shows the Upper Back Panel (E) but do the same for Bottom Stringer (I).
  • Page 45 STEP 29 continued... Example of 4 screws being placed horizontally in wall studs on part E and part I. Please note this is just an example - all wall stud distances are different. dorelhome.com...
  • Page 46 Part 2 - Assembly The next steps are to assemble the metal bed frame mechanism and door panels. Assembly steps will cover pages 47-70. As mentioned on page 2: Choose one of the two options below... • You may continue to use the Professional and a second person, •...
  • Page 47 STEP 30 (x3) (x4) (x1) (x1) First, press each rubber foot (19u) into each hole in the Leg (19c) as shown below. Then, join and assemble the Left & Right bed frame assemblies (19a & 19b) as shown below using bolts (19o) with the provided hex key (19s). You may use a rubber mallet to help join the two frame assemblies.
  • Page 48 STEP 31 (x8) (x8) (x1) (x4) Place the four U-Brackets (19i) in the locations. Use the bolts (19o) and washers (19q) to assemble the U-Brackets (19i) to the joined bed frame assemblies (19a & 19b) as shown. Use the provided hex key (19s) to assemble.
  • Page 49 STEP 32 (x1) (x4) (x2) Assemble the mattress holders (19d) to the frame assemblies (19a & 19b) with bolts (19p) as shown to the right. Use the provided hex key (19s) to assemble. dorelhome.com...
  • Page 50 STEP 33 (x4) (x4) (x4) long end short end Assemble two pistons (19h) to each side of the bed frame assembly with clevis pins (19l) and secure each one with a cotter pin (19n). 19h 19h long end long end The ends of both pistons need to be inserted into the groove of the bed frame when assembled.
  • Page 51 STEP 34 (x1) (x2) (x2) The cabinet is not shown to allow a clear view of the bed frame assembly With a person on each side, lift the bed assembled bed frame, line up the holes of the frame assembly with the large bushing hole of the Left and Right Pivot arm (19e &...
  • Page 52 STEP 35 Critical Step... Please read directions carefully! (x4) (x1) With a person on each side, carefully lift the bed frame in the closed position. While one person pushes the bed frame into the cabinet, beyond the 90 degrees, the other person is to engage the "front" Gas Piston (19h) on each side of the unit, to the front pin of the Left and Right Pivot push here...
  • Page 53 STEP 35 continued... This image shows the bed frame pushed into the cabinet, beyond 90 degrees. BED FRAME 90 DEGREES (WHEN THE BED FRAME IS IN THE UPRIGHT MOST POSITION) Please note: it is normal to see the bed frame in this state prior to the gas pistons being installed.
  • Page 54 STEP 36 (x2) (x1) (x2) Be sure the bed frame is fully assembled to the unit cabinet. (This step could use both people). Once certain, carefully pull the bed frame down, then assemble the Leg (19c) as shown with the clevis pins (19m) and cotter pins (19n). The cabinet is not shown to allow a clear view of the bed frame assembly...
  • Page 55 STEP 37 (x4) With the help from another person, carefully place the Top (C) onto the Left Side Rail (L), Right Side Rail (M) and Top Rear Rail (N). Use screw (10) as shown. A ladder will be required. Do not lean against the top of the unit, it may cause sagging dorelhome.com...
  • Page 56 STEP 38 (x2) (x2) With the help of another person, assemble the disassembled LED lights (24d) to the Top (C) with screw (11). Thread the LED lights (24d) wires through the holes provided in Top (C) to allow the wires to be placed on top of the Top (C). Bed frame mechanism is removed from view to better show this step...
  • Page 57 STEP 39 (x2) With the help of another person, feed the LED light wires through the wire saddle (20) in the Top (C) and through the one on the top edge of the Upper Back Panel (E) if needed. Clip the Light Plugs (24d) (that is fixed into the transformer (24a)) back into the LED light wires.
  • Page 58 STEP 40 With the help of another person, assemble the LED lights back together. First placing the lens into the base and then screwing the cover back to the base as shown below. Adjust any wires necessary as needed. Assure the Power Supply Plug is close to where power outlet is located.
  • Page 59 STEP 41 (x6) (x3) dorelhome.com...
  • Page 60 STEP 42 (x2) (x4) dorelhome.com...
  • Page 61 STEP 43 (x3) (x2) (x10) dorelhome.com...
  • Page 62 STEP 44 (x2) (x6) (x4) With help from another person, hold the Upper Vertical (O) upright & steady and place the Center Panel (S) behind the brackets, pressing the panel flush with the metal plate (23). Use screw (12) to assemble the two parts together.
  • Page 63 STEP 45 (x2) (x4) dorelhome.com...
  • Page 64 STEP 46 Support Rail IMPORTANT: First, unlock and flip the leg into the cabinet. Then, lower the bed frame down a bit to allow clearance to hook Door Panels. This step could use both people. Carefully lift Door Panel (P), position the Brackets (27) over the three Support Rails of the Bed Frame, and drop into position.
  • Page 65 STEP 47 This step could use both people. Lower the bed frame to the open position. One person will need to hold the bed frame in the open position while the other person places the Lower Horizontal (R). Position the Lower Horizontal (R) to the left of the Lower Vertical (P).
  • Page 66 STEP 48 (x2) (x2) (x2) Do not fully tighten these screws dorelhome.com...
  • Page 67 STEP 49 Support Rail This step could use both people. Close the bed frame. Position the assembled Upper Vertical (O) and Center Panel (S) to the left of the Lower Vertical (P) and on top of Lower Horizontal (R). Lift the assembled Upper Vertical (O) and Center Panel (S), position the Brackets (27) over the upper two Support Rails of...
  • Page 68 STEP 50 Support Rail This step could use both people. Position the Upper Horizontal (Q) on top of the Lower Vertical (P). Lift the Upper Horizontal (Q), position the Brackets (27) over the upper Support Rail of the Bed Frame, and drop into position. The cabinet is not shown to allow a clear view of the bed frame assembly...
  • Page 69 STEP 51 (x4) (x16) This step could use both people. Carefully pull the bed frame open. Place the 4 remaining metal plates (23) as shown. Ensure there are no gaps between the panels. Use screw (12) to fasten metal plates (23). The cabinet is not shown to allow a clear view of the bed frame assembly...
  • Page 70 STEP 52 (x11) (x3) (x11) (x8) Align the entire assembly so that the edges are lined up with the bed frame and push up against the leg. This will set the top gap. Then fasten the panels to the bed frame with the remaining brackets (19).
  • Page 71 STEP 53 (x30) (x60) Press a Plastic Cap (19j) at each end of a Wood Slat (19g). Press both Plastic Caps (19j), attached to the Wood Slat, into the holes of the Metal Bed Frame. Repeat the procedure for all 30 wood slats and 60 plastic caps.
  • Page 72 Maximum Loads This unit has been designed to support the maximum loads shown. Exceeding these load limits could cause sagging, instability, product collapse, and/or serious injury. This bed is designed to accommodate a Queen Size Mattress, up to 10" inches thick. * with a maximum weight of 70 lbs (31.8 kgs) * with a minimum weight of 35 lbs (15.9 kgs) After you have finished installing and...
  • Page 73 Register your product to receive the following: * New trend details - sneak peek on what's new * Surveys - have a voice within our community * Exclusive deals and discount codes * Quick and easy replacement part service To register your product, visit ameriwoodhome.com Visit your local retailer's website, rate your purchased product and leave us some feedback! dorelhome.com...
  • Page 74 Español Portada: Cama de pared Queen Size ADVERTENCIAS E INFORMACIÓN SOBRE LA SEGURIDAD DEL PRODUCTO. NO PROCEDA SIN REVISAR DETENIDAMENTE. ANTE CUALQUIER PREGUNTA, CONTÁCTESE CON EL SERVICIO DE ATENCIÓN AL CLIENTE. ¡No devuelva este producto! Contáctese primero con nuestro equipo del servicio de atención al cliente para obtener ayuda. Llame: 1-800-489-3351 (gratuito) Visite: www.dorelhome.com Para ver la garantía limitada válida...
  • Page 75 Español Parte 2: Montaje - Los pasos del montaje requieren emplear a dos personas que deberán ser capaces de alzar y fijar las partes de la cama con elementos de ferretería: - Puede seguir empleando al profesional y a una segunda persona, o bien - Emplear a dos personas que tengan experiencia en el montaje de muebles listos para montar.
  • Page 76 Español Página 4-5: Identificación de la placa Tamaño no real A - panel izquierdo K - riele del estante B - panel derecho L - riele lateral izquierdo C - superior M - riele lateral derecho D - inferior N - riele trasero superior E - panel trasero superior O - vertical superior F- panel trasero central...
  • Page 77 Español Página 8: Identificación del marco de la cama No es el tamaño real No todas las partes estarán identificadas. 19l - Pasador de horquilla grande 19a - Montaje izquierdo 19m - Pasador de horquilla pequeño 19b - Montaje derecho 19n - Pasador de chaveta 19c - Pata 19o - Perno M6 x 16 mm...
  • Page 78 Español Página 10: Orientación de la cerradura de leva Presione el conector frontal (13) en los orificios del panel trasero superior (E) y luego coloque el otro extremo de los conectores frontales (13) en los orificios del riel trasero superior (N). Presione las dos piezas para que se traben. Tenga en cuenta que las piezas estarán sueltas en los orificios hasta que presione ambas piezas juntas.
  • Page 79 Español Página 31-32: de herrajes eléctricos Información sobre la longitud de los cables: 1. El cable de alimentación mide 72 pulg. desde el transformador hasta la punta del enchufe. 2. El cable del bucle para el disco sensor, desde el transformador es de 48 pulg. hasta el centro del bucle. 3.
  • Page 80 Español Página 33: Coloque el transformador (24a) en el panel de la cabecera (H) en la ubicación que se muestra. Use el tornillo (14) para fijar el transformador (24a). Enrosque el enchufe de la fuente de alimentación (24b) en frente del larguero inferior (I) si es necesario para la fuente de alimentación. Página 34: Con la ayuda de otra persona, coloque la unidad en posición vertical con cuidado.
  • Page 81 Español Página 37: Con cuidado, coloque la unidad AL RAS de la pared. En la parte trasera de la unidad hay muescas. Estas deben coincidir con el zócalo de la pared. Si el zócalo es más alto o más grueso que las muescas incluidas en la unidad, tendrá que quitar el zócalo, cortarlo para que quepa en ambos lados de la unidad y volver a fijarlo luego a la pared.
  • Page 82 Español Página 41: Montantes de madera y de metal En primer lugar, asegúrese de que la unidad esté nivelada en todas las direcciones. Tal como se muestra en la vista de la derecha, fije la unidad a los montantes con tornillos (3) y arandelas (26).
  • Page 83 Español Página 46: Parte 2, Montaje Los siguientes pasos consisten en montar el mecanismo del marco metálico de la cama y los paneles de las puertas. Los pasos del montaje abarcarán las páginas 47-70. Tal como se mencionó en la página 2, elija una de las dos opciones siguientes: - Puede seguir empleando al profesional y la segunda persona, o bien - Emplear a dos personas que tengan experiencia con el montaje de muebles listos para montar.
  • Page 84 Español Página 50: Monte dos pistones (19h) en cada lado del ensamblaje del marco de la cama con pasadores de chaveta (19l) y asegure cada uno con una chaveta (19n). El extremo “largo” de cada pistón debe fijarse al marco Durante su montaje, debe insertar los extremos de ambos pistones en la ranura del marco de la cama.
  • Page 85 Español Para acoplar el pistón "trasero" a gas (19h) a cada lado de la unidad, mueva el marco de la cama de un lado al otro de manera lenta y con cuidado hasta que pueda introducir los pistones a gas (19h) en la clavija trasera de los brazos pivotantes izquierdo y derecho (19e y 19f).
  • Page 86 Español Página 57: Con la ayuda de otra persona, pase los cables de la luz LED a través del soporte para cables (20) en la parte superior (C) y a través del que se encuentra en el borde superior del panel posterior superior (E) si es necesario.
  • Page 87 Español Página 66: No apriete completamente estos tornillos Página 67: Riel de soporte Este paso puede ser realizado por ambas personas. Cierre el marco de la cama. Coloque el panel vertical superior (O) y el panel central (S) ensamblados a la izquierda del panel vertical inferior (P) y sobre el panel horizontal inferior (R).
  • Page 88 Español Página 72: Cargas máximas Esta unidad ha sido diseñada para soportar las cargas máximas mostradas. Exceder estos límites de carga podría generar un hundimiento, inestabilidad, el desplome del producto o lesiones graves. Esta cama está diseñada para alojar un colchón queen size de hasta 10 pulgadas de grosor. * con un peso máximo de 70 lb (31,8 kg) * con un peso mínimo de 35 lb (15,9 kg) Una vez que haya terminado de instalar y montar la cama abatible, conserve el manual de...
  • Page 89 Français Page de couverture : Lit mural Queen Size AVERTISSEMENTS ET INFORMATIONS RELATIVES À LA SÉCURITÉ DU PRODUIT. NE PROCÉDEZ PAS SANS LES LIRE ATTENTIVEMENT. POUR TOUTE QUESTION, CONTACTEZ LE SERVICE CLIENTÈLE. Ne renvoyez pas ce produit! Contactez d'abord notre service clientèle pour obtenir de l'aide. Appelez-nous : 1-800-489-3351 (gratuit) Rendez-vous sur : www.dorelhome.com pour consulter la garantie limitée valable aux États-Unis et au Canada.
  • Page 90 Français Partie 2 - Assemblage - Les étapes d'assemblage nécessitent l'intervention de deux personnes qui doivent être en mesure de soulever et de fixer les pièces du lit à l'aide de la quincaillerie : - Vous pouvez continuer à utiliser le professionnel et une deuxième personne, ou - Faites appel à...
  • Page 91 Français Page 4-5 : Identification des pièces Pas de taille réelle A - Panneau de gauche K - Rail d'étagère B - Panneau droit L - Rail latéral gauche C - Haut M - Rail latéral droit D - Bas N - Rail arrière supérieur E - Panneau arrière supérieur O - Verticale supérieure...
  • Page 92 Français Page 8 : Identification du cadre de lit Pas la taille réelle Toutes les pièces ne sont pas identifiées. 19l - Grand axe de chape 19a - Assemblage gauche 19m - Petit axe de chape 19b - Assemblage droit 19n - Goupille fendue 19c - Pied 19o - Boulon M6 x 16 mm...
  • Page 93 Français Page 10 : Orientation du verrouillage à came Poussez le connecteur avant (13) dans les trous du panneau arrière supérieur (E), puis placez l'autre bout du connecteurs avant (13) dans les trous du rail arrière supérieur (N). Poussez les deux pièces ensemble pour les verrouiller. Remarque que les pièces seront lâches dans les trous jusqu'à...
  • Page 94 Français Page 31-32 sur le matériel électrique Informations sur la longueur du cordon : 1. Le cordon d'alimentation mesure 72 pouces du transformateur à l'extrémité de la prise. 2. Le câble en boucle pour le disque du capteur, à partir du transformateur, mesure 48 pouces jusqu'au centre de la boucle.
  • Page 95 Français Page 31-32 : Matériel électrique Informations sur la longueur du fil : 1. Le cordon d'alimentation mesure 72 pouces du transformateur jusqu'au bout de la fiche. 2. Le fil de boucle pour la rondelle du capteur, du transformateur, mesure 48 po jusqu'au centre de la boucle.
  • Page 96 Français Page 33 : Placez le transformateur (24a) sur le panneau de tête de lit (H) à l'emplacement indiqué. Utilisez le vis (14) pour fixer le transformateur (24a). Vissez la fiche d'alimentation (24b) dans l'avant du rail inférieur (I) si nécessaire pour l'alimentation électrique. Page 34 : Avec l'aide d'une autre personne, replacez soigneusement l'appareil à...
  • Page 97 Français Page 37 : Placez soigneusement l'unité FLUSH au mur. Il y a des encoches à l'arrière de l'appareil. Ces derniers doivent correspondre à la plinthe du mur. Si la plinthe est plus haute ou plus épaisse que les encoches incluses avec l'appareil, vous devrez retirer la plinthe, la couper pour l'adapter aux deux côtés de l'appareil, puis rattachez-le au mur.
  • Page 98 Français Page 41 : Montants en bois et en métal D'abord, assurez-vous que l'appareil est de niveau dans toutes les directions. Comme indiqué sur la vue de droite, fixez l'unité aux goujons à l'aide de vis (3) et de rondelles. (26). Cette vue montre le panneau arrière supérieur (E), mais faites de même pour le rail inférieur (I). Tu doit placer au moins trois vis dans trois goujons différents, en s'étendant horizontalement, bien qu'il soit préférable de vissez-en quatre dans la pièce E et la pièce I.
  • Page 99 Français Page 46 : Partie 2, Assemblage Les prochaines étapes consistent à assembler le mécanisme du cadre de lit en métal et les panneaux de porte. Les étapes d'assemblage s'étendront sur les pages 47 à 70. Comme mentionné à la page 2, choisissez l'une des deux options suivantes : - Vous pouvez continuer à...
  • Page 100 Français Page 50 : Assemblez deux pistons (19 h) de chaque côté de l'ensemble du cadre de lit avec des goupilles fendues (19 l) et fixez chacun avec une goupille fendue (19n). L'extrémité « longue » de chaque piston doit être attachée au cadre Lors du montage, vous devez insérer les extrémités des deux pistons dans la fente du cadre de lit.
  • Page 101 Français Pour fixer le piston à gaz « arrière » (19 h) de chaque côté de l'unité, déplacez le cadre de lit d'un côté à l'autre lentement et avec précaution jusqu'à ce que vous puissiez insérer les pistons à gaz ( 19 h) dans l'axe arrière des bras pivotants gauche et droit.
  • Page 102 Français Page 57 : Avec l'aide d'une autre personne, faites passer les fils de l'éclairage DEL à travers le support de fil (20) en haut (C) et à travers celui situé sur le bord supérieur du panneau arrière supérieur (E) si nécessaire.
  • Page 103 Français Page 66 : Ne serrez pas complètement ces vis Page 67 : Rail de support Cette étape peut être effectuée par les deux personnes. Fermez le cadre du lit. Placez le panneau vertical supérieur (O) et le panneau central (S) assemblés à gauche du panneau vertical inférieur (P) et sur le panneau horizontal inférieur (R).
  • Page 104 Français Page 72 : Charges maximales Cet appareil a été conçu pour supporter les charges maximales indiquées. Le dépassement de ces limites de charge peut entraîner un affaissement, une instabilité, un effondrement du produit et/ou des blessures graves. Ce lit est conçu pour accueillir un matelas Queen Size, d'une épaisseur maximale de 10 pouces. * avec un poids maximum de 70 livres (31,8 kg) * avec un poids minimum de 35 livres (15,9 kg) Après avoir terminé...

This manual is also suitable for:

4335356com

Table of Contents