Related Manuals for Greiner Vibrograf Magnomaster Plus
Summary of Contents for Greiner Vibrograf Magnomaster Plus
- Page 1 Operating instructions Magnomaster Plus Version: 01-2024-EN Date: 09.04.2024 Greiner Vibrograf AG Mittelstrasse 2 CH-4900 Langenthal...
-
Page 2: Table Of Contents
GENERAL INFORMATION ....................... 3 ................3 NFORMATION ON THESE OPERATING INSTRUCTIONS ....................3 NFORMATION ON CUSTOMER SERVICE ..........................3 NTENDED USE SAFETY INSTRUCTIONS ........................4 DELIVERY AND STORAGE ....................... 5 ............................5 ELIVERY ......................5 NCOMING GOODS INSPECTION ............................5 TORAGE ...................... -
Page 3: General Information
1 General information 1.1 Information on these operating instructions This is the original operating manual for the product Magnomaster Plus from Greiner Vibrograf The version and language can be found on the title page. 1.2 Customer service information If you have any questions about the product or require any other service related to the product, you are welcome to contact our customer service. -
Page 4: Safety Instructions
2 Safety instructions PLEASE NOTE! Short circuit due to damaged mains cable Material damage to the device → Remove damaged cable → Lay the cable in such a way that it cannot be damaged by external influences → Only have work on the MMA+ carried out by customer service PLEASE NOTE! Damage caused by electromagnetic radiation during demagnetisation Material damage to devices and items (mobile phone, credit card, etc.) -
Page 5: Delivery And Storage
Dispose of the packaging material appropriately. 3.2 Incoming goods inspection Check the delivery immediately upon receipt for completeness and transport damage. Complain about any defects immediately. 3.3 Storage Store the Magnomaster Plus under the following conditions: • Dry and dust-free • Protect from sunlight •... -
Page 6: Installation, Commissioning And Function
4 Installation, commissioning and function 4.1 Installation The MMA+ should be set up in an environment without magnetic fields. Once the device has been calibrated with the SET button, the position may no longer be changed. 4.2 Commissioning 1. Connecting the mains cable 2. - Page 7 WARNING Damage caused by electromagnetic radiation Personal injury → During demagnetisation, maintain a safety distance of 1 m vertically above the demagneti- sation area for critical body parts Do not lean over the demagnetisation area during demagnetisation → During demagnetisation, maintain a safety distance of 40 cm horizontally around the de- magnetisation area for critical body parts This does not include pressing the button, as the hand and arm are not critical body parts...
-
Page 8: Functional Description
4.3 Functional description Picture 1 Figure 1 shows the MMA+ with its two main components 1 + 2. 1 ➔ deposit position for test objects (watches) with sensor board underneath 2 ➔ 3.5" colour TFT 480 x 320 pixel display with resistive touchscreen The MMA+ can be used for two applications: Determination of magnetic contamination of a test specimen (e.g. - Page 9 The sensor board is equipped with 36 sensors, each with an average centre-to-centre distance of 7.5 mm. Each individual 3D magnetic sensor determines the surrounding three-dimensional magnetic field with the vectors X-Y-Z at a resolution of 0.025 μT and a maximum measured value (magnetic flux den- sity B) of ±1400 μT.
-
Page 10: Measure Magnetism
5 Measure magnetism The MMA+ should be set up in an environment without magnetic fields. To calibrate the device, press the start arrow to the right of SET. Always without test sample! The device is calibrating. - Page 11 Calibration is complete when the display shows a micro-Tesla value. Once the device has been calibrated, its position may no longer be changed!
-
Page 12: Demagnetising
6 Demagnetising The DEMAG function can be used at any time (even without calibration). Install holder for watch bracelets, if required Place the watch on the mat in the rear area... - Page 13 Press the start arrow to the right of DEMAG for demagnetising with the MMA+ The process (approx. 2 seconds) is indicated by the colour change of the DEMAG graphic and a overlaying time bar instead of the arrow key.
-
Page 14: Technical Data
7 Technical data 7.1 Technical data Tension 110 V to 230 V Performance 20 VA Quiescent current when no button is pressed 20 mA Peak current over approx. 10 ms at the start of 120 mA demagnetisation at 115 V Peak current over approx. -
Page 15: Disorders
Malfunctions Malfunction Possible cause Remedy The MMA+ cannot be The MMA+ is switched off. Switch on MMA+. switched on. The mains cable is not Plug in the mains cable. Demagnetisation does not plugged in. work. Technical defect. Contact customer service. -
Page 16: Waste Disposal
Waste disposal The disposal centres and authorities are country-specific. Observe the local regulations for dis- posal. The appliance must be returned to the appropriate collection centre. Or it can be disposed of by a specialised company. -
Page 17: Ce Declaration Of Conformity
10 CE Declaration of Conformity...
Need help?
Do you have a question about the Magnomaster Plus and is the answer not in the manual?
Questions and answers