Table of Contents
Advertisement
Quick Links
Berner- Kochsysteme GmbH & Co. KG
Sudetenstrasse 5 - D-87471 Durach
Tel. +49 (0) 831/697247-0; Fax. - 15
Email:
Original User manual
Installation-induction devices
Be sure to read the instructions for use and assembly
before installation - installation - commissioning.
This protects you and prevents damage.
Berner@induktion.de
|
www.induktion.de
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Berner BI3EGMO
Summary of Contents for Berner BI3EGMO
- Page 1 Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D-87471 Durach Tel. +49 (0) 831/697247-0; Fax. - 15 Email: Berner@induktion.de www.induktion.de Original User manual Installation-induction devices Be sure to read the instructions for use and assembly before installation - installation - commissioning.
-
Page 2: Table Of Contents
Table Table ............................1 Safety ............................4 Safety regulations ......................... 5 Description of Hazard Symbols ..................... 5 Dangers in case ofnon-observance of safetyregulations ..............5 Safe use ............................ 5 Improper operation ........................6 Changes / use of spare parts ....................... 6 Pan detection .......................... - Page 3 Warming function with pyro sensor and touch ................17 Warm holder ..........................18 Warm holder with potentiometer ....................18 Warm holder with touch ......................18 Hot holder with Spin Control ...................... 19 Wipe Control ..........................20 .............................. 20 Operation ..........................20 Temperature .........................
- Page 4 BIPMS-GeneratorEn ........................37 BIPMS Generators ........................38 Devices with BIPMS generators: ....................38 BIPDS Generator ........................40 BIPDSGenerators ........................41 Devices with BIPDS generators: ....................41 BIPDMS/BIPDMMSGenerator ...................... 43 BIPDMSGenerators ........................44 Devices with BIPDMS generators: ....................44 GDP(D)MMS-Generators ......................45 Devices with BIPMMS/BIPDMMS generators: ................
-
Page 5: Safety
Safety Read this guide carefully. Keep the instructions for use and assembly for later use or for subsequent owners. Check the device after unpacking. Do not connect in the event of transport damage. Record the damage in writing and call the customer service, otherwise the warranty claim will not be waived. -
Page 6: Safety Regulations
Safety regulations Description of Hazard Symbols General danger symbol Failure to comply with safety regulations means danger ( injuries ) This symbol warns of dangerous tension. (Figurine 5036 of IEC 60417-1) This symbol warns against non-ionizing electromagnetic radiation. (Figurine 5140 of IEC 60417-1) Attention In case of improper use may cause minor injuries or... -
Page 7: Improper Operation
To avoid overheating of the pans by empty cooking, do not heat the pan unattended and without cooking. Turn off the heating zone if you take the pan away for a while. This prevents the heating process from automatically start when a pan is placed back on the heating zone. Thus, unattended heating is avoided, i.e. -
Page 8: Pan Detection
Pan detection Pans with a diameter of less than 12 cm (bottom) are not recognized. During operation, the power indicator lamp, LED or digital display indicates the selected power level (1-9). When operating without a pan or an unsuitable pan material, no power is emitted, the power indicator lamp flashes only briefly or the indicator does not report a pot detected see error messages. -
Page 9: Technical Device Data
Technical device data Power table 1 channel (single generator BIPS, BIPMS) Block Mwp Function Performance setting See performance table Master Potentiometer Function Generator 2 takes potentiometer value from From generator 1 Control procedure Pulse for installation and multi-cooker units Impulse Frequency Frequency for single cookers CAN ID / Operating Frequency... -
Page 10: Power Table 2 Channel (Double Generator Gdp(D)Mms, Bipdms, Bipds)
Type Type Sw1 4 230V 400V Power[kW] Power[kW] Current Current 10.9 8.75 13.1 10.0 15.3 12.5 Power Table 3 Phases Generator BIPS Type Type Sw1 4 400V 230V Power[kW] Power[kW] Current Current 7.25 8.75 10.2 10.0 12.3 12.5 Power table 2 channel (double generator GDP(D)MMS, BIPDMS, BIPDS) Block Sw. - Page 11 Power table 1 phases doubleenerator GDP(D)MMS 1x230V Mach3 Power Channel 1 [kW] Power Channel 2 [kW] Single Dual Single Dual SW1 Application operation operation operation operation High High High High KR210 60-H R220 60H W30 75H WH60-90 WH60-150 Performance table 1 phases doubleenerator BIPDMS 1x230V Mach4 Power Channel 1 [kW] Power Channel 2 [kW] Single...
-
Page 12: Installation
GR70-250 205H Installation Electrical data of the devices Devices by power (3.5 kW- BIPMS3.5) Induction cooktop 1-phase (voltage 230Volt +5% / -10%) Connection Color Frequency Backup Phase Brown, Black or 1 50 Hz / 60 Hz 1 x 20A F (fast) Blau or 2 Working Tax security... -
Page 13: Functional Conditions
frequency 22-35 Yellow/Green Functional conditions max. tolerance of mains voltage nominal voltage+5%/-10% Frequency50 / 60 Hz Protection class in delivery stateIP 11 min. pan diameter12 cm Installation environment Maximum ambient temperature Storage >-20°C to +70°Cin Function>+5°C to +35°C maximum relative humidity Storage>... -
Page 14: Commissioning
The device has a suction filter. Nevertheless, you must ensure that no fat ambient air caused by other applications can be sucked into the inductiongerät (near fryers, grill plates or fryers). The air intake temperature must be below +35°C. Operators must ensure that all installation, maintenance and inspection work is carried out by approved personnel. -
Page 15: Devices On And Off Switch
Devices on and off switch Position OFF:Position ON: '0' points to the mark ()'I' points to the mark (). οο Power control with potentiometer With the potentiometer, the power is infinitelyadjustable. The knob can be rotated via the 0 position. This means that a quick changeover from the low to the high power level and vice versa. -
Page 16: Warming Function (Optional)
The power level is displayed on the 3-digit display in the middle. For this purpose, the LED ring with a strongly luminous LED displays the power position parallel to the rotary knob. When it is moved, a tail appears as an optical effect. Elements Description Function indicates the function-dependent direction of... -
Page 17: Warming Function With Potentiometer
Warming function with potentiometer Instead of power levels 1 to 3, the warming temperature can be set from 70-110°C. This is followed by the performance settings from level 4 to 9. Elements Description Function Rotary switch From 0 position Rotary switch Temperature control 70-110°C (level 1-3) Range α40-120°... -
Page 18: Warming Function With Pyro Sensor And Touch
Warming function with pyro sensor and touch Instead of the potentiometer (Poti must NOT be connected), the touch display takes control. The device is switched on by means of the on-off button. The function key can be used to switch between power control and temperature control. The temperature range is from 70-240°C in 1°C increments with the Up and down buttons adjustable. -
Page 19: Warm Holder
Warm holder In contrast to the warming function, which can be switched as an option for power induction, the hot holder is a separate application. (see applications) The hot holder is a pure temperature control unit. There are 2 temperature ranges to choose from: 60-90°C, 60-150°C The temperature is measured by means of PT1000 sensors under the ceramic glass. -
Page 20: Hot Holder With Spin Control
Button for 1 sec to press On-Off button Switching on or off Setpoint setting On button Quick press: increment in 2 steps Long actuating: increment in 10 steps Setpoint setting From Taste Quick press: decrement in 2 steps Long actuating: decrement in 10 steps Hot holder with Spin Control The set temperature is set on the knob. -
Page 21: Wipe Control
Wipe Control Control panel for function-dependent operation with 2 touch buttons, touch slider and different display elements. Inputs for connecting 4 additional PT1000 sensors. A maximum of two Wipe Control can be used per induction. Elements Description Function 3 Digit 7 Segment Display Setpoint display Should / Actual value display LED bar with 19 red LED's... -
Page 22: Temperature
be carried out. Instead, the timer is set for the associated hob. The middle display shows the power position in parallel with a strongly luminous LED to the Touchslider. When it is moved, a tail appears as an optical effect. Resolution in half steps 1.0..9.0 = 17 positions, (new: Boost function is triggered with stay at the highest slider level for 1sec when Boost is ena- bled,... -
Page 23: Display In Case Of Error
With long pressing of the button, a timer can be started, which will reduce the induction after the set time and signals the end with a short beep. there are two methods for setting the time a) Tap: Rough adjustment e.B. in std steps by tapping on right or left end of the touch slider. Medium adjustment e.B. -
Page 24: Powerstar Function ( Bi2Eg3.5Xx; Bi4Eg7Xx )
Powerstar function ( BI2EG3.5xx; BI4EG7xx ) The 230V double generator automatically optimizes the maximum power of 3.5kW. There can be optionally 2 cooking points with a maximum output of 1.8 kW each or only the front cooking unit with 3.5 kW or the rear cooking unit with 3.0 kW. The other cooker must be switched off. When both cookers are operated, the digital display displays level 7 at full power on both cookers. -
Page 25: Operation
If the power indicator and or LED or digitale indicator remains switched off or flashes only very briefly, check the following: Is the inductiongerät connected to the power grid or main switch in? Is the power knob on position ON? Do you use an induction-ready pan (test with permanent magnets) with a floor diameter of at least 12 cm? Is the pan in the middle of the heating zone (except appliances with suction coils with 5-... -
Page 26: Pot Detection
Pot detection The pot detection has the task of switching on the inductive heating when a suitable cookware is installed on the ceramic field, or switched off again if this is removed. The pot detection is carried out inductively with test pulses every second, after 1 minutes the clock rate is reduced to a 5 seconds. -
Page 27: Function With Priority Circuit (Dual Potentiometer Control (Optional))
Set to full power and observe flashing point at the 7-segment display at the bottom right. reduce power until the point is permanently lit. The performance level, which is then displayed, corresponds to the pot rating The larger the number, the better the cookware (values of 1-9). Pot rating premium with 4 display touch... -
Page 28: Master Potentiometer (Optional)
Device is switched off 0 position 0 position Device switches on Potentiometer 1 specifies the performance Turn Potentiometer 2 specifies the performance Turn Command takeover Potentiometer 1 specifies the performance Switching off and on again Device turns off Master Potentiometer (optional) Master Slave Slave... -
Page 29: Decommissioning
Master-Potentiometer function for both channels on. If still additional potentiometers are connected to the device, they will only work if the Master-Potentiometer is set to zero position. Energy The power limits are set individually for single operation and dual operation per application. Thus, after application, one is reduced the performance in dual operation in order not to exceed the maximum total power. -
Page 30: Potentiometer Error Handling
The inductiongcan only be opened by approved and trained service personnel. Stop any work, the Heating zone ( ceranglass ) can be torn or broken. The inductiongerät must be switched off immediately and From Network Separated Be. Do not touch any parts inside the device. Attention when opening the induction device! Dangerous tension! - Page 31 Choose a pan suitable for induction. Compare the Used pan is not ideal results with'your' pan. Air cooling system is Make sure that the air supply and export are not disabled/blocked obstructed/blocked. Air filter is dirty. Clean or replace filters. Insufficient heating capacity Power indicator lamp is Ambient temperature is too high...
-
Page 32: Overview Alerts On Display
Overview Alerts on Display Display Importance Declaration Development and diagnostic mode Raw mode No limits active! Display only on standby DC current greater than 350mA (too many or wrong fans) Overcurrent flashing. Display every 10 seconds for 1 second. Fan not connected or blocked Display appears every 10 seconds for 1 second. -
Page 33: Guarantee
List of detergents for certain types of contamination: Type of pollution Cleaner Light pollution Moist cloth ( Scotch ®) with something Industrial kitchen cleaning products Fatty spots (sauces, soups,...) Polychrome, Sigolin chromium, Inox cream, Vif Super-Cleaner Supernettoyant, Sida, Wiener Klak, Pudol System Care Lime and water stains Polychrome, Sigolin chromium, Inox cream, Vif Super-Cleaner... -
Page 34: Maintenance
Devices intended for this purpose can be sent to us for disposal. Only enough prepaid packages are accepted by us. Delivery: Berner- Kochsysteme GmbH & Co. KG Sudetenstrasse 5 - D - 87471 Durach Tel. +49 (0) 831/697247-0; Fax. - 15 Email: Berner@induktion.de... -
Page 35: Generatorviews
Generatorviews Page 34 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... -
Page 36: Spare Parts
Spare parts BIPS-Generator • •• • • •• •• • • • • •• ••• • • • • • • . •• •• • • •• •• •• •• •• •• •• • • • • • • • •... -
Page 37: Bips Generators
BIPS Generators Devices with BIPS generators: BI1EG5, BI1EG7, BI1EGF5, BI1EGF7, BI1EGG5, BI1EGG7, BI1EGGF5, BI1EGGF7, BI1EGSP5, BI1EGSP, BI1EGSF5, BI1EGSF8, BI1EGSPW, BI1EGSPQ1, BI1EGSPL1, BI1EGR5, BI1EGR7, BI1EGHK8, BI1EGHK9, BI2EGQ14, BI2EGFFQ10, BI2EGFFQ14, BI2EG14, BI2EGFF10, BI2EGFF14, BI2EGF10K, BI2EGF14K, BI2EGF10W, BI2EGF14W, BI1EG5GN, BI3EGQ15, BI3EGQF10, BI3EGQF15, BI3EGQF21, BI4EG28, BI4EGDF20, BI4EGDF28, BI4EGDF20K, BI4EGDF28K, BI4EGF20W, BI4EGF28W, BI6EGAF30K, BI6EGAF42K,... -
Page 38: Bipms-Generatoren
BIPMS-GeneratorEn • • •• •• • • •• • • • • •• •• Page 37 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... -
Page 39: Bipms Generators
Devices with BIPMS generators: BI1EGM2. 5, BI1EGM3.5, BI1EGS2. 5, BI1EGS3.5, BI1EGS5, BI1EG2.5B,BI1EG3.5B,BI1EG5B,BI1EG3.5,BI1EGR3.5, BI1EG3.5GN, BI2EG5M,BI2EG7M, BI3EGQ10, BI4EG10M, BI4EG14M, BI1EGMO, BI2EGMO, BI3EGMO, BWEB3.5, BWEBFW3.5, BWEBM2.5, BWEB BWEBM3.5, BWEB2MQ5, BWEB2MQ7, BWEB2M5, BWEB2M7, BI1EGSW, BI1EGW, BI1EGGSW, BI1EGGW, BI1EGS3.5T, BI2EGS7QT, BI2EGS10QT, BI2EGS7TK, BI2EGS10TK, BI4EGS14TK, BI4EGS20TK, BWEBT3.5... - Page 40 Page 39 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018...
-
Page 41: Bipds Generator
BIPDS Generator • • •• •• • • •• • • •• •• • •• •• •• •• •• •• •• •• • • • • • • • • • •• Page 40 Of 57 17.07.2014 • Ver. 3.7 ©... -
Page 42: Bipdsgenerators
BIPDSGenerators Devices with BIPDS generators: BI1EGSP2, BI1EGSM2, BI1EGSPW2, BI1EGSPQ2, BI1EGSPL2, BI2EGQ7,BI2EGQ10, BI2EGFFQ7, BI2EG7, BI2EG10, BI2EGFF7, BI2EG7K, BI2EG10K, BI2EGF7K, BI2EG7SK, BI2EG10SK, BI4EG14, BI4EG20, BI4EGD14, BI4EGD20, BI4EGDF14, BI4EG14K, BI4EG20K, BI4EGD14K, BI4EGD20K, BI4EGDF14K, BI4EG14SK, BI4EG20SK, BI6EG21K, BI6EG30K, BI6EG30K, BI6EGAF21K, BI2EGAQ7, BI2EGAQ10, BI2EGA7, BI2EGA10, BI2EGAR10, BI4EGA14, BI4EGA20, BI6EGA21, BI6EGA30, BI4EGAL14, BI4EGAL20,... - Page 43 Page 42 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018...
-
Page 44: Bipdms/Bipdmmsgenerator
BIPDMS/BIPDMMSGenerator •• •• • • • • •• • • •• •• • •• •• • • •• •• •• •• •• •• • • Page 43 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... -
Page 45: Bipdmsgenerators
BIPDMSGenerators Devices with BIPDMS generators: BI2EG3.5SK, BI2EG3.5M, BI4EG7SK, BI4EG7KK, BI4EG7M, BI2EGS3.5QT, BI2EGS3.5TK, BI4EGS7TK Page 44 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... -
Page 46: Gdp(D)Mms-Generators
GDP(D)MMS-Generators Devices with BIPMMS/BIPDMMS generators: BI1EG-W,-WB,-WW; BI1EGG-W,-WB,-WW; BI2EGG-W,-WB,-WW • " " " " • • • Page 45 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... -
Page 47: Technical Documentation
Technical documentation Gluing scheme for flush-mounted installation Air flow Air flow module Air way coil generator Separate (Standing/ Lying) Page 46 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018... - Page 48 Page 47 Of 57 17.07.2014 Ver. 3.7 © Bernese cooking systems 2018...
-
Page 49: Observe Installation Regulations
Observe installation regulations Supply air guide via guided channels from below (option from front or rear) (Option with Flex. supply air hose). Under the induction, a floor plate must be attached, on which supplied CNS angle (as guide for the aluminium air filter). It is essential that the floor plate is removable so that, in the event of service, access to the generator, or in the case of a separate variant, access to the coil, is guaranteed for the service technician. -
Page 50: Attention Points For Remote Coil (Coil - Generator Separated)
The intake air must be channelled and fed directly to the fans via the supplied filter. The suction cross-section should be at least 200 cm2. The maximum intake air must never exceed the temperature of 35°C directly in front of the fans. -
Page 51: Installation Instructions For The Installation Of
Installation instructions for the installation of Induction devices with support frame (Ver. A) Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. - Page 52 Laying of the connecting cables. Please note in case of separate generator installation: Sensor, display and probetapped cables (control cables) must be laid separately from coil cables and generator cables and, if possible, placed in a steel channel. Coil cables must not be routed in metal ducts and must not be laid bundled.
-
Page 53: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. B) of induction devices Please note the following installation instructions. This is the only way to ensure trouble- free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. - Page 54 Pactan Apply a thin schicht on the inner frame to fix the ceramic glass. Please apply in the area of the display only very sparingly to prevent the ad segment from sticking. Insert the ceramic glass into the fresh Pactan schicht on the inner frame.
-
Page 55: Installation Instructions For The Installation Of
Installation instructions for the installation of Sensor keypads with support frame (Ver. A) Frame incl. electronics is vorassembled with glued ceramic glass Please followthe instructions on page 29 Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. -
Page 56: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. A2) of sensor keypads Frame incl. electronics is pre-assembled with glued ceramic glass Please followthe instructions on page 29 Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life. In the event of a breach of these requirements, the device warranty expires. -
Page 57: Installation Instructions For Flush-Mounted Installation
Installation instructions for flush-mounted installation (Ver. B) of sensor keypads Frame incl. electronics is pre-assembled with glued ceramic glass (2 - 3mm projection) Please follow the instructions on page 31 Please note the following installation instructions. This is the only way to ensure trouble-free operation and a long service life.
Need help?
Do you have a question about the BI3EGMO and is the answer not in the manual?
Questions and answers