Subscribe to Our Youtube Channel
Related Manuals for Nordson ARAG echo100
Summary of Contents for Nordson ARAG echo100
- Page 1 COMPUTER FOR THE MANAGEMENT OF BOOMS WITH AIR SLEEVE 46700200 Software rel. 1.0.x INSTALLATION, USE AND MAINTENANCE...
-
Page 2: Table Of Contents
LEGEND OF SYMBOLS LEGEND OF SYMBOLS • = Generic danger = Warning CONTENTS • LEGEND OF SYMBOLS ....................................2 • MANUAL FOREWORD AND USE ..................................3 • MANUAL USE MODES ..................................... 3 • RESPONSIBILITY ......................................3 PRODUCT DESCRIPTION ....................................3 RISKS AND PROTECTIONS BEFORE ASSEMBLY ............................ -
Page 3: Manual Foreword And Use
INTRODUCTION • MANUAL FOREWORD AND USE This manual provides instructions to assemble, connect and set the device. Any other information is provided in specific sheets to be used exclusively by the installer, containing specific information of each model. • MANUAL USE MODES The section of this manual dedicated to the installation contains information for installers. -
Page 4: Installation
INSTALLATION POSITION ON FARMING MACHINE Diagram for connection CONNECTION POINTS Farming machine power supply (12 Vdc) Hydraulic electric valve (fan motor control) RPM sensor (fan rotation status) COMPONENTS INCLUDED IN THE PACKAGE COMPONENTS TO BE PURCHASED SEPARATELY Positioning • ECHO 100 must be placed in the control cabin of the farming machine. -
Page 5: Wiring Connections
INSTALLATION WIRING CONNECTIONS • Only use ARAG harnesses suitable for ECHO 100. • Take care not to break, pull, tear or cut the cables. • Use of unsuitable cables not provided by ARAG automatically voids the warranty. • ARAG is not liable for any damage to the equipment, persons or animals caused by failure to observe the above instructions. General precautions for a correct harness position •... -
Page 6: Accessories
INSTALLATION Power supply connection The power connector must be directly connected to the battery of the farming machine; Fig. 7 shows the drilling template of the power connector. Fig. 7 Fig. 6 Fig. 5 WARNING: To avoid short circuits, do not connect the power cables to battery before the installation is completed. Before powering up the device, make sure the battery voltage is as specified (12 Vdc). -
Page 7: Setup
PROGRAMMING SETUP Turning ON / OFF • Ordinary switching on Software version ECHO 100 1000 RPM Ver 1.0.0 Fig. 9 Keep key pressed until switching on the device: after the software version, the display shows the job screen (Fig. 9). •... -
Page 8: Use Of Keys For Setup
PROGRAMMING Use of keys for setup Language 1 Press the arrow keys in succession to move across the menu items English next item, previous item); the selected item will be displayed (Fig. 12). 2 Press to access the menu: during set-up, a cursor blinks on the display Constant (Fig. -
Page 9: Advanced Setup
PROGRAMMING ADVANCED SETUP The computer can be set-up with all the data required to ensure a correct configuration of the device. This operation must be done once only, when installing the computer. 10.1 Tests and checks before programming Before proceeding with device programming, check the correct installation of all components, the connection to the power supply and to the components. -
Page 10: Access To The User Menu (With Device On)
PROGRAMMING User Menu 10.3 Access to the (with device ON) Keep the key pressed until the menu is displayed: - - - - U s e r - - - - Menu Preset Setup Preset 1/10 1000 RPM Par. 10.3.1 Display contrast Par. -
Page 11: Test Device (Tests Are Reading-Only Data)
PROGRAMMING Test device 10.3.5 (tests are reading-only data): • Display operation test Turns on all the display points to test their correct operation. Battery voltage • Displays the supply voltage. Test PWM • Allows testing the correct operation of the hydraulic circuit and of the relevant fan-piloting valve. Increases / decreases the fan-piloting valve actuation. -
Page 12: Use
Upon device turning on, the actuation of the fan-controlling hydraulic valve will be possible ONLY AFTER a prolonged pressure key. ON/OFF 1000 RPM Expected (target) RPM value 150 RPM Preset Setup (par. 10.3.1): 1000 RPM DIRECT CONTROL mode active (par. 11.1.1) 1000 RPM (02) 1500 RPM 150 RPM... -
Page 13: Maintenance / Diagnostics / Repairs
MAINTENANCE / DIAGNOSTICS / REPAIRS MAINTENANCE / DIAGNOSTICS / REPAIRS 12.1 Troubleshooting DISPLAYED ERROR FAULT CAUSE REMEDY OPERATION ERROR DETECTED No power supply Check power supply connection (par. 6.1) The display does not switch on Device is OFF Press the ON key Battery Voltage Displayed error Power supply voltage is below 9 V... -
Page 14: End-Of-Life Disposal
TECHNICAL DATA END-OF-LIFE DISPOSAL Dispose of the system in compliance with the established legislation in the country of use. GUARANTEE TERMS 1. ARAG s.r.l. guarantees this apparatus for a period of 360 days (1 year) from the date of sale to the client user (date of the goods delivery note). - Page 16 Only use genuine ARAG accessories or spare parts to make sure manufacturer guaranteed safety conditions are maintained in time. Always refer to the internet address www.aragnet.com. 42048 RUBIERA (Reggio Emilia) - ITALY Via Palladio, 5/A Tel. +39 0522 622011 Fax +39 0522 628944 http://www.aragnet.com info@aragnet.com...
Need help?
Do you have a question about the ARAG echo100 and is the answer not in the manual?
Questions and answers