Advertisement
Quick Links
Lifetime Limited Warranty
If you have a question about your MOBB
Healthcare device
please
contact
Healthcare dealer.
MOBB
Healthcare
original consumer purchaser for as long as
they own their MOBB product that it will
be
free
from
defects
workmanship
under
warranty is only applicable to products
used in residential applications within the
United States and Canada
transferable
to
Should defects in material or workmanship
exist during the applicable warranty period
in any MOBB Healthcare Product, MOBB
Healthcare
will elect at its discretion to
either
repair
or
material. This warranty covers only parts
and materials of the products supplied by
MOBB Healthcare. Not covered under this
warranty
are wear
abuse of the product in a manner that was
not intended for the product to be used.
This warranty shall become void if the
product is in any way modified, improperly
adjusted or abused
.
Important Warnings
• Please follow all instructions and warnings
to avoid hazardous situations that can
result in property damage and/or patient/
resident/staff/caregiver injury and/or death.
• Inspect the product for damage and loose
hardware before each use.
• DO NOT use the product if it appears to
be damaged or unstable and DO NOT
modify the product in any way.
or
this
warranty,
an authorized MOBB
warrants
to
in material
normal
use.
and
is
subsequent
owners.
replace
the defective
and
tear
items
the
2 in 1 Tilting Overbed Table
and
This
not
or
116A Viceroy Rd. Unit 5-6 Concord,
MHMTAB
Weight Capacity: 50 lbs
MHMTAB
MOBB Healthcare Ltd.
Ontario, L4K 2M1 Canada
www.mobbhhc.com
Advertisement
Related Manuals for MOBB Health Care MHMTAB
Summary of Contents for MOBB Health Care MHMTAB
- Page 1 2 in 1 Tilting Overbed Table they own their MOBB product that it will free from defects in material MHMTAB workmanship under normal use. This warranty is only applicable to products used in residential applications within the...
-
Page 2: Product Structure
Product Structure: The key components include: Long tabletop Positioning bar Short tabletop Plastic lever Table support assembly 2" plastic wheels(without brakes) Support pipe assembly Base assembly 2" plastic wheels(with brakes) Preparation Before Assembly: First remove the packaging, If assembling on the floor, place cardboard or a carpet underneath to prevent scratches. - Page 3 Hardware components: • B1: 2-inch plastic wheels (without brakes) • B2: 2-inch plastic wheels (with brakes) • B3: Spring washers • B4: Cylindrical head inner hexagon screws (M8x60) • B5: φ8.2 washers • B6: Plastic lever • B7: Carriage bolts (M6x65) •...
- Page 4 Step 1: As shown in Figure 1, install the two B1 2-inch plastic wheels (without brakes) and B3 spring washers into the corresponding screw holes at the rear end of the base. Step 2: As shown in Figure 1, install the two B2 2-inch plastic wheels (with brakes) and B3 spring washers into the corresponding screw holes at the front end of the base.
- Page 5 Figure 4 Step 5: As shown in Figure 4, align the square pipe of A3 table top assembly with the slot of A2 support assembly. Use 2, B9 carriage bolt(M8x45) and B10(M8) to secure them. Post-Installtion Check: 1. Verify if the table is installed correctly and if all four legs are level. You can compare it with the diagrams in the manual.
-
Page 6: Intended Use
Angle Adjustment Instructions: As shown in the diagram below, lift the table until the support component underneath the tabletop locks into the slot. You can adjust it to the angle that suits your needs. Product Maintenance and Care: 1. Do not allow hard objects to scratch or damage the surface of the product to prevent material damage.
Need help?
Do you have a question about the MHMTAB and is the answer not in the manual?
Questions and answers