Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for STATESMAN SKBD500SS
Summary of Contents for STATESMAN SKBD500SS
- Page 1 SKBD500SS 5 LITRE CHILLED DRAUGHT BEER DISPENSER Instruction Manual Please read these instructions carefully before use and retain for future reference. Before switching on your appliance – Always check for any damage that may have been caused in transit.
-
Page 2: Table Of Contents
Important Safety Instructions ......... 3-4 Product Specification............5 Appliance Overview ............. 6 Installation ................. 7-8 Operating Instructions ........... 9-17 Cleaning & Maintenance ..........18-21 Trouble Shooting Guide ............ 22 Mains Plug Fuse Replacement ......... 23 Disposal Information ............23 Statesman Warranty/Guarantee Information ....24... -
Page 3: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Please ensure you read all instructions and warnings in this user guide prior to first use and keep this user guide for future reference. • Do not operate the appliance with a damaged cord or plug, or after it malfunctions or has been dropped or damaged in any way. - Page 4 • After use clean the components as directed in the cleaning and maintenance section. Dry thoroughly with a clean, dry cloth. • Never allow children to operate, play with or crawl inside the beer dispenser. • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the...
-
Page 5: Product Specification
PRODUCT SPECIFICATION Voltage AC 220-240V/50Hz Available capacity 5 Litre Rated operating power Cooling performance Adjustable 2~12℃ (Ambient temperature is from 22 to 24℃) Noise level ≤50dB(A) (Ambient noise ≤25dB(A)) Dimensions (mm) H:430 x W:272 x D:414 Net weight (kg) 6.65 pressure outlet unit Stainless steel appearance Aluminum radiator system... -
Page 6: Appliance Overview
APPLIANCE OVERVIEW 1. Top Cover 2. CO Connector and Casing 3. Beer Tap Handle 4. Beer Tap Mechanism 5. Beer Dispensing Unit 6. Drain Switch 7. Drip Tray 8. CO Pressure Dial 9. LED Display/Temperature Control Buttons 10. Top Cover Release Button 11. -
Page 7: Installation
INSTALLATION 1. Take the beer dispenser out of the box and place it on a flat, level surface. Ensure that the sides and back of the beer dispenser are at least 10 cm away from walls or any other items to ensure proper ventilation. 2. - Page 8 5. Make sure the drain switch is closed and there is nothing obstructing the cooling chamber. Place 800ml of cold water into the cooling chamber or fill to the max line on the inside of the cooling chamber. The drain switch is closed Max water level line (approx.
-
Page 9: Operating Instructions
OPERATING INSTRUCTIONS Universal 5 Litre Kegs WARNING: Before connecting you should always follow the instructions marked on the beer keg to eliminate excess gas. Ensure that the keg has rested long enough to avoid the beer becoming too foamy. 1. Open the top cover of the beer dispenser and disconnect the dispensing unit from the tap mechanism and CO connector. - Page 10 WARNING: Make sure the CO pressure dial is set to off (-) and the beer tap is closed. 4. Lift the keg into the cooling cavity. Reconnect the CO connector and beer tap connector tubes with the dispensing unit. Once in place the tap mechanism will make a “Ka”...
- Page 11 6. Close the top cover of the beer dispenser. Turn on the power switch at the base of the appliance. 7. Until ready to pour the beer, the pressure valve should be turned towards the off (-) position. When ready, turn the valve towards the on (+) position to release the CO , turn the valve back to off (-) when pouring is stopped or paused.
- Page 12 10. The cooling temperature of the beer dispenser is adjustable between 2-12 ℃. The machine has a power-off memory function. The startup temperature will revert to the previous temperature that was set. The original factory setting temperature upon first use will be 4℃. 11.
- Page 13 Pre-carbonated Kegs Pre-carbonated kegs are pre-charged with CO and so do not require the use of an additional CO canister. The empty CO casing and connector should be secured in the top cover as shown in the diagram below. 1. Pre-carbonated kegs come with a pre attached tap. This needs to be removed before the keg can be used in the beer dispenser.
- Page 14 Please Note: when removing the adapter nozzle, press the edges inwards to Adapter nozzle release from the keg. 4. Close the top cover and operate the beer dispenser as per operating instructions for the Universal Keg, steps 7-15. Replacing the Beer Keg 1.
- Page 15 3. Lift and remove the beer keg from the dispenser using the handle on the dispensing unit. Unclip the beer dispensing unit and pull free from the empty beer keg. 4. A new keg can then be installed according to the operating instructions. We recommend cleaning the tap mechanism each time the beer keg is replaced (see 'Cleaning and Maintenance' section).
- Page 16 Replacing the CO Canister Please change the CO canister if beer can no longer be poured but there is still beer in the keg. 1. Ensure the beer tap is closed and the CO pressure valve is set to the off (-) position.
- Page 17 Replacing the Water Inside the Cooling Cavity It is recommended to replace the water inside the cavity at least once a week. Please Note: The water does not need replacing each time the beer keg is changed, once a week is sufficient. 1.
-
Page 18: Cleaning & Maintenance
CLEANING AND MAINTENANCE Before first use and after use the beer dispenser should be fully cleaned as follows: 1. Clean the outside with a dry cloth. 2. Connect the piercing pin end of the beer dispensing unit to the end of the cleaning tube. - Page 19 7. Rinse out the inside of the cooling cavity with warm water and then drain into the drip tray by opening the drain switch. Dry the inside with a clean cloth. 8. Detach and empty the drip tray and wash with warm water. Dry thoroughly with a clean cloth.
- Page 20 Canister connector Joint sealing ring Empty canister Changing the Beer Tap Tube If the beer tap tube breaks or begins to leak it should be replaced as follows: WARNING: The appliance should be switched off and unplugged before part replacement. A keg should not be installed in the dispenser.
- Page 21 Changing the Dispensing Unit Sealing Ring In case of air leakage in the beer dispensing unit replace the sealing ring on the beer suction pipe. WARNING: The appliance should be switched off and unplugged before part replacement. A keg should not be installed in the dispenser.
-
Page 22: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE If you experience difficulties with the appliance, please check the suggestions below before contacting customer services on 01473 277 508: Problem Possible Cause Possible Solution Make sure the beer tap The beer tap tube is not connector is securely properly connected. -
Page 23: Mains Plug Fuse Replacement
MAINS PLUG FUSE REPLACEMENT Fuse Cover Fuse Replacement (Class I) This appliance must be earthed. Remove the fuse cover with a small flat head screw driver. Take out the fuse and replace with a new fuse of the same Amp. Replace the fuse cover and push back into place. -
Page 24: Statesman Warranty/Guarantee Information
STATESMAN WARRANTY/GUARANTEE TERMS & CONDITIONS THANK YOU FOR CHOOSING STATESMAN As a valued customer we would like to offer you a FREE 2-year warranty to cover your product against any electrical or mechanical defects. This means that in the unlikely event you develop a fault or problem with your product we will happily repair or replace the item free of charge. - Page 28 38 Bluestem Road, Ransomes Europark, Ipswich, IP3 9RR EU: Castle Electrical Factors Ltd., Dundalk, A91 KA9R, IR 01473 277 508...
Need help?
Do you have a question about the SKBD500SS and is the answer not in the manual?
Questions and answers