CONTENT 1.READ AND SAVE THESE INSTRUCTIONS Safety Instructions ......................01 2.S1050 Series Comparison 2.1.Component Introduction................... 01 2.2.Comparison ........................ 04 2.3.Control Box ......................... 05 3. Installation 3.1.Installation Steps ....................... 05 3.2.Extension cords and Signal amplifier..............08 3.3.How to Cut and Splice....................08 4.Remote...
• External dimmer cannot be used with this product. • Use this product with the provided power adapter only. Thank you for choosing the ASAHOM RGBWW Permanent Outdoor Lights . This product has an IP67 water-resistant rating, making them ideal for outdoor use. You can Choose from 99+ presets and 16 million colors to decorate house via Smart Life app.
Page 4
Control Box Refer to 2.3 Control Box 0.2m/0.6ft Control Box 4m/13ft String Section The length of the string section is 5 m, with 10 lights 0.5m/1.64ft Adhesion Prep Pad Used to strengthen the adhesion between 3M adhesive and the pasting surface ADHESION PREP PAD ADHESION PREP PAD Screw Clip...
Signal Amplifier When using extension cords with more than 4 extension cords, the signal amplifier is used to amplify data transmission.Refer to 3.2 Extension cords and Signal amplifier Amplifier Waterproof Connector Refer to 3.3 How to Cut and Splice Remote Ruler Refer to 4.Remote Used to quickly confirm the distance...
2.3.Control Box Short press: Color Adjustment Long press for more than 5 seconds: Turn on Remote pairing Short press: ON/OFF Long press for more than 5 seconds: Reset device Short press: Brightness Adjustment Blinking blue: In network distribution status Steady blue: The device is online Off: device is offline Installation Notes: ●...
Page 8
① Before installation, connect each string light and plug it into power to make sure every string light can work properly. The string light might not light up if you plug it into power first and then connect the string light sections ②...
Page 9
⑤ Use the Adhesion Prep Pad to wipe the surface to make 3M paste stronger.Tear off the 3M gum on the back of a light and firmly press it against the surface for more than 5 seconds. The slight rotation of the power cord will not affect the use. ⑥...
The S1060 series can be connected to up to 6 extension cords When there are more than 4 extension cords, a signal amplifier needs to be connected before the first extension cord to ensure signal stability. Note:You can buy extension cords and signal amplifiers at ASAHOM’s Amazon store. Amplifier 1.8m 1.8m...
d.Insert exposed wires into corresponding slots. e.Firmly screw connector and push silicone plug into shell. It is recommended to use a wrench to tighten the waterproof connector nut to prevent the risk of water intrusion due to long-term exposure to heavy rain. ②...
2700K ②Keep pressing the Remote ON button for a long time. If the pairing is successful, 6500K the light string will turn on or off once. 4.2.Remote function Button Function Turn on the lights Turn off the lights 2700K 2700K 2700K always on 6500K 6500K always on...
5.1.Download Smart Life APP Download the Smart Life app from the App Store (iOS devices) or Google Play (Android devices). Note:You can use the APP for free. If charges appear on the APP after downloading, please check whether you downloaded the wrong APP. 5.2.Pairing Your Light with the Smart Life App What You Need: ●...
5.3.Pattern Function 5.3.1.Overal color adjustment ① Switch to Select All ② Click on the color patch...
Page 15
5.3.2.Single light color adjustment ① Switch to Deselect All ② Click on the color patch,adjusting the relative brightness can control the brightness of a single light ③ Click or slide in the light string area...
5.3.3.Save pattern to favorite ① Click the favorite button ② The current pattern wil be saved in Favorite 5.4.Animation Function 5.4.1.Preset Click the Preset icon to execute the corresponding lighting effect. Click the heart in the upper right corner of the Preset icon to pin the Preset to the top.
Page 17
5.4.2.DIY Provides 15 basic DIY effects. On this basis, you can modify the color, change speed, etc. to create your own exclusive lighting effects. ① Click + ② Choose a Dynamic ③ Click the color and then click + to add the color to the current effect. You can choose up to 8 colors. ④...
Page 18
5.4.3.Folder Select preset or DIY to form a folder, and the lights will perform corresponding effects accord- ing to the set order and time. ① Click + ② Click Choose Pre-set or DIY + ③ Choose Preset or DIY ④ Set the validity period of the corresponding preset or DIY...
5.5.Music 5.5.1.Device Music mode Built-in 6 device music modes ①Adjust sensitivity for the best lighting effects ②Click the upper right corner of the icon to reset the setting color Note: The farther the sound source is from the control box, the higher the sensitivity needs to be set to achieve the best effect.
5.7.Light number setting When increasing or decreasing the number of lights, reset the number of lights to ensure that the lights can achieve the best display effect. ① Click on more icon ② Click light number setting ③ Click to Refresh ④...
5.8.Add Remote ① Click on more icon ② Click Add Remote ③ Click Pair, and the control box will enter the remote control pairing state. ④ Keep pressing the Remote ON button for a long time. If the pairing is successful, the light string will turn on or off once.
3. After the operation, you can voice control via Alexa/Google Assistant. Note: The troubleshooting section below is for solving frequently asked questions for the product. If your problem persists, please feel free to contact us via Amazon Messenger or email at : asahom.service@outlook.com Problem Possible Cause...
Page 24
5GHz WiFi network is not Connected to 5GHz WiFi supported. Please set the router to 2.4GHz and then reset it. Install the control box close to The control box is far away from the the router to minimize obstruc- router tion Cannot connect to Wi-Fi.
Page 25
The control box failed to success- Reset the number of lights fully identify the number of light Refer to 5.7 Light number setting strings Only some lights are After changing the order of the Poor contact between light string light string, reset the number of connectors lights The color of the light...
F F CC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the S1050 Series and is the answer not in the manual?
Questions and answers