Page 1 Integrated Mount Tester User Manual (V2.1)
Page 2 Thank you for purchasing the Integrated Mount Tester. Please read the manual before using the Integrated Mount Tester and use properly. For using the Integrated Mount Tester safely, please first read the 「 Safety information」 carefully in the manual. The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period.
Page 3: Table Of Contents
Content 1 .Safety information ------------------------------------------------------------------------ 1 2. Integrated Mount Tester Introduction -------------------------------------------------- 3 2.1 General ------------------------------------------------------------------------------------------------------ 3 2.2 Features ------------------------------------------------------------------------------------------------------ 3 2.3 Packing list -------------------------------------------------------------------------------------------------- 6 2.4 Function interface ------------------------------------------------------------------------------------------ 7 3. Operation -------------------------------------------------------------------------------- 10 3.1 Installing the Battery ------------------------------------------------------------------------------------- 10 3.2 Instrument connection ----------------------------------------------------------------------------------- 11 3.2.1 IP camera connection ----------------------------------------------------------------- 11...
Page 4 3.3.16 AHD camera test ----------------------------------------------------------------------------- 64 3.3.17 AUTO HD --------------------------------------------------------------------------------------- 66 3.3.18 Cable Test --------------------------------------------------------------------------------------- 67 3.3.19 RJ45 cable TDR test ------------------------------------------------------------------------- 70 3.3.20 Cable Tracer ------------------------------------------------------------------------------------- 72 3.3.21 TDR cable test ---------------------------------------------------------------------------------- 73 3.3.22 Analog video generator ---------------------------------------------------------------------- 77 3.3.23 Network tool ------------------------------------------------------------------------------------ 78 (1)IP address scan ------------------------------------------------------------------------------------- 78 (2)PING Test -------------------------------------------------------------------------------------------- 78...
Page 5 3. 4 Audio test ------------------------------------------------------------------------------------------------ 108 3.5 HDMI output -------------------------------------------------------------------------------------------- 108 3.6 PoE power output --------------------------------------------------------------------------------------- 108 3.7 DC12V 2A power output ------------------------------------------------------------------------------- 109 3.8 USB 5V 2A power output ------------------------------------------------------------------------------ 110...
Page 6: Safety Information
1 .Safety information ◆ The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station,etc. ◆...
Page 7 ◆Never perform capacitance measurements unless the capacitor to be measured has been discharged fully. ◆Never measure any of resistance, capacitance, diode or continuity measurements on live circuits. Visual laser sources When you turn on visual laser sources, please don’t stare at it, or will damage to eyes. When not using it, please turn it off and cover the protective cap .
Page 8: Integrated Mount Tester Introduction
2. Integrated Mount Tester Introduction 2.1 General The 7 inch touch screen Integrated Mount Tester is designed for maintenance and installation of IP cameras, analog cameras, CVI, TVI AHD, SDI cameras, as well as testing 4K H.265 camera by mainstream.The 1920x1200 resolution enables it to display network HD cameras and analog cameras in high resolution.
Page 9  Analog video generator, support CVBS loop test, tester can sends and receives color bar signal, check the continuity of the BNC cable.  LAN interface traffic monitoring, display upload/download rate etc parameters when connecting LAN port or wireless WIFI. ...
Page 10  Video image digital zoom to view the image in greater detail.  Snapshot function allows you to save the current image as a JPG file in the tester.  Built in enhanced Analog video generator, send the color, pure blue and black image, test monitor transmission channel and debug display device, observe whether there are light spots or black spots on the monitor.
Page 11: Packing List
 DC5V 2A power output for USB charging (No USB data exchange, voltage only),as a power bank for the phone.  PoE power output, supply temporary power for PoE camera.  Audio input and output, test and output the audio signal. ...
Page 12: Function Interface
2.4 Function interface Press more than 2 seconds, turn on or off the device ,short press to turn on or off the men u display Menu key 4xzoom the image displays Far focus: Focus the image faraway Near focus: Focus the image nearby TELE:Zoom in the image WIDE:Zoom out the image Open/set,confirm the setting of parameters, open or enlarge the aperture...
Page 13 Downward, set function or reduce the value of the parameter. Tilt the PTZ downward Confirm key Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture Multimeter interface The charge indicator:It lights red while the battery is being charged. As the charging is complete, the indicator turns off automatically The RS485 data transmission indicator: it lights red while the data is being transmitted...
Page 14 SDI input (BNC interface) RS485 Interface: RS485communication for the PTZ HDMI IN Video signal output (BNC interface)/cable tracer interface CVBS input /AHD /TVI/CVI Coaxial interface Optical power meter interface PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera) PSE power sourcing equipment.Test PoE voltage/LAN test port DC 12V 2A power output , for provisional DC power supply LED lamp...
Page 15: Operation
3. Operation 3.1 Installing the Battery The battery main switch at the right-bottom corner of tester bottom. “0”: Battery power off “1”: Battery power on The tester has built-in lithium ion polymer rechargeable battery,the tester’s bottom power should turn to “0”for safety during transportation (the factory default is “0”) .
Page 16: Instrument Connection
3.2 Instrument connection 3.2.1 IP camera connection Power an IP camera with an independent power supply, then connect the IP camera to the tester’s LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means the IP camera and the tester are communicating.
Page 17: Analog Camera Connection
3.2.2 Analog camera connection (1)Connect the camera's video output to the tester’s VIDEO IN. The image will display on the tester after pushing the PTZ icon. (2) Tester’s “VIDEO OUT” interface connects to the Video input of monitor and optical video transmitter and receiver, the image display on the tester and monitor.
Page 18: Hd Coaxial Camera Connection
3.2.3 HD Coaxial camera connection SDI/EX-SDI, CVI, TVI, AHD camera are classified as HD coaxial cameras. Hereby the following instruction of how to connect SDI camera to the tester is also applied to CVI, TVI, and AHD camera. (1) Connect the SDI camera's video output to the tester’s “SDI IN” interface, the image will display on the tester.
Page 19: Osd Menu
3.3 OSD menu Press the key 2 seconds to turn on. Press the key again to turn off. short press the key to enter sleep mode, press it again to test. If tester works abnormally and cannot be turned off , Press the key several seconds to turn off, the tester reset.
Page 20: Short Cut-Menu
WLAN: Turn on WLAN net and displays current WLAN status. 3.3.2 Short cut-menu You can call shortcut menu by press tester’s “menu” key, you can self- define shortcut menu. Press the key” “, you can turn on it, and switch functions, then press to enter app, tap other area on the screen, to exit the menu.
Page 21: Screen Capture
3.3.3 Screen capture Long press the key “enter”, can capture screen interface and save it in any time. 3.3.4 Link monitor Tap icon "Link Monitoring" at left corner on the screen, to enter. It can detect instrument port rate 10/100/1000M, signal quality detection, upload and download speed, etc.
Page 22: Testerplay
3.3.5 TesterPlay Mobile screen projection (Only for android version) . The meter creates WIFI hotspot, connect mobile phone to the tester’s WIFI hotspot, or the tester and mobile phone connect to the same Wi-fi network. Tap icon “ ”, then select “TesterPlay” app to enter, the meter generates two-dimensional code, Please use mobile phone scan it, then download and install the client software, you can view the screen real-time projection.
Page 23: Ip Discovery
3.3.6 discovery Press IP discovery ,tester auto-scan the whole network segment IP, as well as auto-modify the tester‘s IP to the same network segment with the scanned camera's IP. Local IP: Tester’s IP address, Tester can auto-modify the tester‘s IP to the same network segment with the scanned camera's IP.
Page 24: Onvif Test
IPC TEST:IPC TEST Quick link. Applicability: Using IP discovery app,you don’t need to know the first two digits of camera’s IP address, it can auto-scan the whole network segment IP, and auto-modify tester’s IP address,greatly improved engineering efficiency. ONVIF test 3.3.7 ONVIF can display 4K H.264 camera image by tester mainstream, one key to activate camera.
Page 25 Click the button “Refresh”, tester will scan the ONVIF camera again. Click the newly displayed ONVIF camera on the “Device List”. The tester will show the IP camera’s relative information and settings. Pop-up settings menu when click the “ONVIF setting” icon in the upper left corner. Across network segments scan: After open this function , enter “Setting - IP Settings - Advanced”to add other network segments IP, Rapid ONVIF function can across network segments to scan camera’s Auto Login:After open this function, tester can auto login camera and display camera image.
Page 26 Video transmission protocol: UTP and TCP protocol. Open password cracker:Cracks password of cameras. View manual:Open Manual. Restore Defaults: Revert “Rapid ONVIF” to default settings. Confirm:Save the modified parameters. Click “MENU” icon to open camera setting. While in the “Live video” menu, click “Video Menu” at the top right of the image to access the following tools: snapshot,record, photo, playback, PTZ and settings.
Page 27 ONVIF PTZ control: Tap the image in the direction you want the PTZ camera to move. Tap the left side of the image to move left, right to go right, up to go up and down to go down. Compatible IP PTZ cameras will rotate accordingly.
Page 28 Image setting: Click “Imaging Set” to adjust image brightness, saturation, contrast, sharpness and backlight compensation mode. Profiles:Click “profiles”,can view video streaming current configuration files, as well as switch between Major stream and minor stream. Page.23.
Page 29 Preview pictures:Quickly preview and zoom in or out pictures, automatically and manual refresh. Identification: Click “Identification” to view information of the camera. Page.24.
Page 30 Time set:Click “Time set”,select "Manual set" to set up the time of camera. Maintenance: For camera software reset or restore to factory settings. Page.25.
Page 31 User Set: Modify camera user name,password, etc. parameters. Network setting:Click “Network Set “to change the IP address. Some cameras cannot support change IP address, so there is no change after saving. Page.26.
Page 32 Zoom in image:Press the key to enter the zoom mode. Press it again to exit zoom mode.When the image is enlarged tap left, right, up or down on the image to move the whole image on the screen. When the image is enlarged, if not operate on touch screen, it can operate by the keyboard,press the to zoon in , press the key to zoom out,press upward and downward key to move image.
Page 33 Snapshot: Click bottom”snapshot” to screenshot the image and store it in the tester. If select manual storage, appears dialog box “Input Name”,user-defined the files name (by Chinese character, English letter or digit) to save in the tester, if select “Auto- storage”,the tester auto stores the files after snapshot.
Page 34 To rename or delete a photo, click and hold on the file until this screen appears: Video files can play in the Video player on the main menu. Set preset position:Move the camera to preset position, enter the preset number on the bottom right corner to complete position preset.
Page 35 PTZ Speed set:Horizontal and vertical speed set. Modify channel name: clicking "OSD" will pop up OSD settings, including time, channel name and other optional items. Page.30.
Page 36 RTSP: Get RTSP address of the current camera. Doc: Auto create testing reports document of camera, click "Create document”. Click Preview to view the report document. Page.31.
Page 37 Enter the camera test information, click "Create Document" to complete the report. Click “Doc” menu again, you can preview the report document. Icons description: the description of function icons on the bottom toolbar. Page.32.
Page 38: Test Tool
3.3.8 Test tool Test tool is developed for installation and debugging of the IP camera, it can display image, and modify IP, user name and password etc. Making camera test more convenient and quickly. Click the tool icon to enter test tool. Activation: select left [online detection] to display the "unactivated"...
Page 39 Play: When mode display “activated” camera, input correct password, click “Play” poping up “private protocol” and “ONVIF”, Select correspond protocol to view the camera image. Modify Channel: Click “Modify Channel”, will pop up OSD setting, includes time, channel name,etc. Page.34.
Page 40 After selected Channel name, can edit channel name, modify the display position and font size. If select “Default position” of Content location, then no need to modify. If select “customize”, then can modify Channel name and display position, click “OK”to view the image. Click “Back” or “Return” button to return previous interface.
Page 41 Input new IP address, need to input password, click “OK” to save the modification. Modify user information: modify camera user name and password, which is onvif, test tool, IPC TESTE user name and password, not web user name and password. Page.36.
Page 42 Factory reset setting: camera will be soft reset, and the device’s user name, password and network set be saved. Other settings information is factory reset. Reset password: Click "reset password", scan the pop-up QR code, will send the result to reminder emai l, then will receive the safety code to reset the camera password.
Page 43: Ip Camera Test
IP camera test Note: Currently, the Test App only supports some brands’ specific IP cameras, these include specific models made by ACTI, AXIS, Dahua, Samsung, and many more. If the camera is not fully integrated, please use the ONVIF or RTSP apps.
Page 44 If the brand has offered official original protocols, please select camera type, input IP camera address ,user name and password ,click” official” to enter the camera image display interface(Currently, only support DAHUA official protocols ). Stream code: When test camera via RTSP, you can select mainstream or sub stream to test (if camera’s RTSP have not been start or without, it will tip “auto match fail, please witch to manually selecting.
Page 45 IP Camera's IP: Enter the IP camera’s IP address manually or click “Search” to auto-scan for the IP camera’s IP address. It is better to directly connect the IP camera to the tester so the search results will only display the camera’s IP address. If the tester is connected to a PoE switch, it will find and display several IP address.
Page 46: Virtual Ipc
3.3.10 Virtual IPC Virtual IP Camera function, simulating ONVIF camera to send video stream, used to test NVR, monitor transmission channel and IP camera, supports wired network and WiFi. After network connection, the virtual IP camera will auto turn on and simulate ONVIF camera to send video stream.
Page 47: Hdmi In
image is normal after replacement, the IP camera is in problem. B. When maintaining IP cameras, this function can be used to send ONVIF video stream to the monitoring center. If the monitoring center can watch the video sent by the tester, the video transmission channel is normal.
Page 48 (2) Video record When you click the “Record” icon, video starts recording. A red recording icon appears on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on the “Record” icon again to stop recording and save the video file in the tester. If select manual storage, before recording begins,appears dialog box “Input Name”,user-defined the files name (by Chinese character, English letter or digit) to store in the tester,tester will hereby store the files after recording.
Page 49 (3)Photo Click the icon “photo” to enter, click the selected thumbnail photo to display it on the screen. Double-tap the image can view full screen. Double-click again the photo to return. To rename or delete an image, click and hold on the file until this screen below appears. Click to close and return to PTZ controller.
Page 50 (4) Recorded video playback Click the “Playback” icon to view your recorded videos. Tap on the video file image you want to watch. To rename or delete a video, click and hold on the file until this screen appears: Video files also can play in the main menu “Video Player". Page.45.
Page 51: Video Monitor Test（Cvbs
3.3.12 Video monitor test（CVBS） Analog camera test and PTZ control, click icon to enter Display the input video image, click the top menu bar icon to enter video level meter (PEAK level, SYNC level, COLOR BURST measurement) Select relative function on the right side Toolbar to operate,functions including“Photos”,“Snapshot”, “Record”,“Playback”,“PTZ”,“Set”...
Page 52 A. Protocol Use the up and down arrow keys to move the yellow cursor to the “protocol”, set corresponding Protocol and support more than thirty PTZ protocols. Such as Pelco-D,Samsung,Yaan,LiLin,CSR600, Panasonic,Sony-EVI etc. B. Port Click and move, to “port” Select the communication port for the PTZ camera controlling (RS485) . C.
Page 53 PTZ Control: Press the key control the PTZ direction of rotation. Press the key , to switch on or turn off the aperture. Press the key , adjust the focus manually. Press the key , manually adjust the zoom. (2) Video and storage setting Click icon “set”,to enter and set analog video image brightness,contrast, color saturation, as well as the file storage way after snapshot and recording, support auto-storage and manual storage.
Page 54 Stretch two fingers outward or inward on the touch screen to zoom the image in or out. If not use touch screen to operate, press the key to zoom out, press the key zoom in, press upward and downward key to move the image. For analog video input, as the resolution is 720*480, it is normal that the zoom in image is not clear.
Page 55 (6)Photo Click the icon “photo” to enter, click the selected thumbnail photo to display it on the screen. Double-tap the image you want to view to make it full screen. Double-click again the photo to return. To rename or delete an image, click and hold on the file until this screen below appears Page.50.
Page 56 Click to close and return to PTZ controller. (7) Recorded video playback Click the “Playback” icon to view your recorded videos. Tap on the video file image you want to watch. Page.51.
Page 57 To rename or delete a video, click and hold on the file until this screen appears: Video files also can play in the main menu “Video Player". (8) Video level meter Click the icon to enter, the Integrated Mount Tester has adopted hardware high-speed sampling and processing technology, can perform both NTSC and PAL video amplitude signal measurements for PEAK to PEAK, SYNC levels and COLOR BURST chroma level.
Page 58 While in PAL format, the unit will be mV, While in NTSC format, it will be IRE. Video signal level 140± 15IRE NTSC Chroma level( COLOR BURST) 40± 5IRE SYNC signal level 40± 5IRE Video signal level 1000± 200mV Chroma level( COLOR BURST) 300±...
Page 59: Sdi/Ex-Sdi Camera Test
For PAL format, the Chroma standard level is 280mV. If the Chroma level is too low, the color will not be as deep, and some details of the image will become lighter. If the Chroma level is too high, there will be distortions on the image. If the coaxial cable is too long, it will reduce the chroma level.
Page 60 The tester supports resolution as follows: HD-SDI: 1280x720P 25/30/50/60 FPS, 1920x1080P 25/30 FPS, 1920x1080I 50/60 FPS EX-SDI:3840x2160P 25/30 FPS,2560x1440P 25/30 FPS,1920x1080P 25/30/50/60 FPS, 1920x1080I 50/60 FPS,1280x720 P 25/30/50/60 FPS The tester’s HDMI output port can be used as SDI to HDMI converter, output HD SDI image to HD TV monitor.
Page 61: Cvi Camera Test
3.3.14 CVI camera test HD CVI camera, CVI dome camera test and PTZ control, click icon to enter. When HD CVI signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows: 2MP@25/30fps ;...
Page 62 Enter PTZ address to perform parameters setting. Operation instructions, please refer to “3.3.1 PTZ (1) Video monitor test”. The PTZ address in the tester must be consistent with the dome camera or decoder, then the tester can test .After setting the parameter, the tester can control the PTZ and lens. Page.57.
Page 63 To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction, PTZ cameras will rotate accordingly. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ.
Page 64 Call preset position Tap the preset position: Tap the preset position area, input preset position number. Tap “call position” to complete call preset position. 1.2 RS485 control Operation instructions, please refer to “3.3.1 PTZ (1) PTZ control parameters setting”. (2)Coaxial amera OSD setting Tap icon “UTC”“, select “menu setting”...
Page 65 Input calling dome camera menu address code, after finishing the parameter settings, you can press the or click the icon to call the dome camera menu . Press arrow keys to set. (3) Snapshot, record, photo viewer and video play back, please refer to “3.3.12 PTZ (1) Video monitor test”.
Page 66 (4) Save setting Click icon “Set” on the right toolbar to enter storage setting. Support auto-storage and manual storage. When select manual storage, user can name and store the files. Focus information: Select enable, will display the focus information and image quality on bottom left c orner of interface.
Page 67: Tvi Camera Test
3.3.15 TVI camera test TVI camera, TVI dome camera test and PTZ control, Click icon to enter. When TVI signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows: 2MP@25/30fps ;...
Page 68 Coaxial camera menu settings Tap icon “UTC”, select “menu setting” to enter the dome camera menu. Page.63.
Page 69: Ahd Camera Test
Input calling dome camera menu address code, after finishing the parameter settings, you can press the or click the icon to call the dome camera menu. More operation instructions (such as PTZ control, Coaxial amera OSD setting ,snapshot, recording and playback etc), please refer to”3.3.6 CVI camera test”.
Page 70 If test 5MP and 8MP camera ,please go tester app"Auto HD " for tesing. Coaxial PTZ control UTC control : select “PTZ control or PTZ control-2”(AHD camera has two different order ,if select “PTZ” cannot control,please go “PTZ-2” ) . If to coaxial PTZ control the AHD camera, no parameters setting is needed.
Page 71: Auto Hd
3.3.17 AUTO HD Auto-recognize the resolution and Auto-display the image of the connected camera. Support coaxial PT Z control and call OSD menu, support up to 8MP CVI/TVI/AHD/CVBS cameras. Coaxial amera OSD setting Tap icon “UTC”“, select “menu setting” to enter the CVI/TVI/AHD/CVBS camera menu. Input calling dome camera menu address code, after finishing the parameter settings, you can press the key“Enable”or click the icon to call the dome camera menu .
Page 72: Cable Test
Press arrow keys to set, Press to confirm. 3.3.18 Cable Test Click icon to enter Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the CCTV tester and cable tester. And then the connecting status, cable type and the sequence of wires as well as the serial number of the cable tester kit will be displayed.
Page 73 The number of the cable tester is 255. If need several different number other types cable testers, should pay the additional cost. Visual judgment of network cable availability: All sequence of cable is correct, generally corresponds to Gigabit straight/cross network cables. Cable sequence is wrong, but the cable is still available, generally corresponds to 100M straight-through/cross network cable.
Page 74 Short-circuit detection: Supports short-circuit detection of the network cable. Testercan perform short-circuit detection even when the remote end is not connected cable tester or cable tracer. Cable test Tap "cable test sketch map", pop up Straight-through cable and crossover cable sketch, It is for line sequence reference, when the crystal on the first pressure in the twisted-pair.
Page 75: Rj45 Cable Tdr Test
3.3.19 RJ45 cable TDR test Connect cable to tester’s LAN port, click icon to enter RJ45 cable TDR test app. Single test: test cable status, length and attenuation. Repeat test: continue to test cable status, length and attenuation. Status: after link up, screen display “online”, if not link up or open circuit, screen display “open circuit”, if cable pair is short circuit, screen display “short circuit”.
Page 76 Advanced Test: test cable pair status, length, attenuation, reflectivity, impedance, skew and other parameters. Attenuation reflectivity: after link up, if reflectivity value is 0, it is the best quality communication. Impedance: after link up ,if the impedance value is 100Ω,it is the best quality communication, the range is generally in 85-135Ω.
Page 77: Cable Tracer
3.3.20 Cable Tracer Connect test cable or BNC cable to the UTP port or the UTP/SCAN (VIDEO OUT) port on the bottom. Click icon to enter. UTP mode is used for searching the normal network cable or other cables. STP mode is used for searching the shielded network cable.
Page 78: Tdr Cable Test
Press the “MUTE” button of cable tracer for 2 seconds. After the “Di” sound, the silent mode is turned on. In the silent mode, can judge cable type according to the indicator light. Press the “MUTE” button again to exit the silent mode. Application It’s convenient for people to find out the other end of the cable from the messy cables in security maintenance and network engineering.
Page 79 (1) Curved trajectory 1) Curve result analysis Inflection point: The position of break point or short-circuit of the cable, is where curve suddenly rises or falls after the smooth curve. Short circuit: The curve shows a downward trend after the inflection point Open (break point): The curve shows an upward trend after the inflection point 2) Curve operation Zoom: Zoom the curve.
Page 80 User-defined calibration: Choose the cable 100 meters to 200 meters (more than 50 meters), click “Cable”, “Type” to select user-defined 1 for calibration, 11 groups user-defined can be set. 1.Select user-defined and click “Calibration “to enter test, click “user-defined 1”can define cable name, such as:AiPu BNC-5.
Page 81 3.Click “+”or”-” to adjust wave speed,while display length is the same with the actual length,click “Save” to save calibration data. It can be used for the same cable testing next time. Application:TDR test is used for pulse reflection method, to transmit pulse signal for tested cable, when cable is open circuit or short-circuit, reflected pulse is generated, the tester receives and deals with the reflected wave, measurement results displayed on the screen.
Page 82: Analog Video Generator
3.3.22 Analog video generator Click to enter, the tester sends the color bars from the “Video out” port,Click the icon “PAL”, select “PAL/NTSC” output formats. Click the selected color-bars, testing image or single bar (red, green, blue, white or black). Double click to full display on the screen and output, click to return main menu.
Page 83: Network Tool
A. When maintaining the dome camera, the tester sends out the color bar by its BNC output to the monitor at the monitoring center. If the monitor receive the color bar, it means the video transmit channel works normally. Meanwhile,on the basis of the received color bar, the monitoring center can judge if transmission has loss or interference.
Page 84: Network Test (Ethernet Bandwidth Test)
Application: PING testing is the most conventional network debugging tools. It is used for testing if the connected IP camera or other network equipment’s Ethernet port is working normally and the IP address is correct. It’s normal that the first data packet will be lost when test start. (3)Network test (Ethernet bandwidth test) To use the Network tester, you will need two testers.
Page 85 a). Start the server: Click “Start Server” button to use the tester as a Server. It will display its IP address at the top of the screen. b). Start send packet test: Using the other tester, type in the Server's IP address at the top right corner of the screen.
Page 86 Tester as Client, tester’s IP address is:192.168.0.139. The Server and the Client are at the same network segment, but with different IP address. Input Server’s IP address 192.168.0.39 in the tester and click “Start” to test network bandwidth. Page.81.
Page 87 Or use tester as a Server, computer as test Client(select Client, input tester’s IP address to test) . When use tester as Server, shows results: Page.82.
Page 88: Port Flashing
(4)Port Flashing Connect a network cable to the meter’s “LAN” port, click the icon to open the Port Flashing app. Click “Start”. The Integrated Mount Tester sends a unique signal to make the connected LAN port of the switch flash. If the tester and PoE switch are connected well, the LAN port of POE switch flash at special frequency.
Page 89: Dhcp Server
(5)DHCP server Click on the DHCP icon to open the DHCP server app. Select the “Start” check box at the top and make any desired changes to the network settings. Click “Save” to start assigning dynamic IP addresses for IP cameras and other networked devices.
Page 90: Link Monitor
Click “start” to trace the goal address. (7)Link monitor Click the icon to open the Link Monitor app. This app is used to see if an IP address is occupied by other network devices. This will avoid new address conflicts. Click “Add”...
Page 91: Rapid Ip Discovery
occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied. 3.3.24 Rapid IP Discovery Connect the cable to tester’s LAN port. Press to enter Rapid IP Discovery app. Click “Start “to search all IP address of connected equipments in whole network segment.
Page 92 Note: 1. Don’t input power into the “DC12/2A OUTPUT” port. 2. Don’t output DC12V/2A power to the DC12V/IN port of the Integrated Mount Tester to avoid damage. 3. The Integrated Mount Tester power output is close to 2A, if the IP camera’s power is over 2V, the tester will auto enter protection mode.
Page 93: Power Input Test
camera or other PoE node must be connected to the LAN port. Note: Do not connect PoE power supply equipment (such as a PoE switch) to the tester’s UTP/SCAN port; otherwise it will damage the tester. PSE transmission When PoE / PSE voltage testing, PoE/PSE conntect to the tester's PSE "IN" port , the camera connetct to tester's Lan port , tester not only can transmit voltage to supply power for camera ,but also transmit data at the same time.
Page 94: Digital Multi-Meter
3.3.27 Digital Multi-meter Click icon to enter. 1) SYMBOLS: U:DC Voltage Measuring A:DC Current Measuring Ω:Resistance Measuring :Diode Testing :AC Voltage Measuring :AC Current Measuring :Continuity Testing :Capacitance Measuring AC/DC Voltage and current measurement state display. Auto- range The Multimeter auto adjust the range by input signal or tested components. Data hold Hold data Display the relative measurement value.
Page 95 2) OPERATING INSTRUCTION DC Voltage Measuring WARNING! You can’t input the voltage which more than DC 660V, it’s possible to show higher voltage, but it’s may destroy the inner circuit. Pay attention not to get an electric shock when measuring high voltage. a.
Page 96 000.0V → 660.0V range 000.0mV → 660.0mV range C. DC Current Measuring (only manual range ) WARNING! Shut down the power of the tested circuit, and then connect the meter with the circuit for measurement. a. Connect the black test lead to the “COM “ jack and the red test lead to the “mA” jack for a maximum of 660mA current.
Page 97 a. Connect the black test lead to the “COM” jack and the red test lead to the”mA” jack for a maximum of 660mA current. For a maximum of 10A, move the red lead to the 10A jack. b. select , enter the AC current measurement, manually select the range. →...
Page 98 Manual range:(Connect the red lead to black leads, will display the measure range) 000.0Ω → 660Ω range 0.000 KΩ → 6.600KΩ range 00.00 KΩ → 66.00KΩ range 000.0 KΩ → 660.0KΩ range 0.000 MΩ → 6.600MΩ range 00.00 MΩ → 66.00MΩ range F.
Page 99 c. Connect test red lead across to the anode, the black lead to the cathode of the diode under testing. d. Connect test red lead across to the cathode, the black lead to the anode of the diode under testing. e .Tested diode, forward voltage low 30mv,there is sound indication ,then can finish the testing quickly without view the screen.
Page 100: Voltage Protection
660uF, the Max time will be 6.6 seconds, if the capacitor is leaked or damaged, the data can’t be read. The tester will be normal after disconnecting the capacitor. Manual range and Auto range When testing, click “Range select " to change the value, click “Auto range “to enter Auto measurement.
Page 101: Optical Power Meter
change the fuse, please opens the battery cover to change. Note: 10A socket without fuse protection, if over the current range. Wrong using the 10A socket to measure the voltage, will damage the meter. 3.3.28 Optical power meter Click icon to enter,with five wavelength 1625nm,1550nm,1490nm,1310nm,1300nm,850nm, linear or nonlinear optical power display, both for optical power testing and fiber link loss relative measurement.It is necessary tool for installation and maintenance optical fiber communication, cable...
Page 102: Visual Fault Locator
Data hold and Relative measuring use together, the data is yellow while the function is effect. 3.3.29 Visual Fault Locator Open Dust Cap, connect fiber to tester's VLS interface. Page.97.
Page 103 Click icon to enter. VFL four statuses can select——”Steady mode”, “Evasive 1Hz”, “Evasive 2Hz”and”Time off”. Click button “Steady mode” to enter steady status, click button “Evasive 1Hz” and “Evasive 2Hz, to enter pulse mode, click button “Time off”, VFL is turned off. Timed turn off can select (5 mins, 10 mins, 30 mins, 60 mins and 120 mins).
Page 104: Audio Record
Click” Steady mode”, red laser source emits steady, click again to quit. Click icons “Evasive 1Hz”or”Evasive 2Hz”to enter pulse mode, the red laser source is emitted by a certain frequency, press it again to quit. 3.3.30 Audio Record Connect an audio device to the Integrated Mount Tester’s audio input port. Click the icon to enter the Audio Recorder app.
Page 105: Audio Player
Please click icon to enter. Click “Setting” to choose the baud rate of RS485; it must be the same as the DVR or the Control. keyboard The DVR or Control keyboard send the code to the tester, if it can be read, the protocol will shown on the upper right, like Pelco D, if not, like P:--- While the tester receives the code, press the key to empty.
Page 106: Update
Click the icon to enter. The Media player can browse video and image files. It supports the video formats of MP4, H.264, MPEG4, and MKV. The Integrated Mount Tester recorded files can play directly via the Media player. The Media player will automatically display the video files from the tester Click on the desired file to play.
Page 107: Led Flashlight
Copy the downloaded update file to SD card "update" directory, if no directory, please create one. icon to open the Update menu. Select “Local Update” to update via the SD card or Click the select “Online Update” to check for updates on the internet. If there are applications that need updating, the applications will be displayed on the screen.
Page 108: Browser
you don’t press the red button to shut off the lamp and press the button to exit the app, the lamp will stay on. Click the Time Setting button to set a timer that will shut off the lamp. 3.3.36 Browser Click icon to enter.
Page 109 Click icon to enter. Language: Select your desired language: English, Chinese, Korean, Russian, Italian , Polish ,Spanish, French or Japanese. Typewriting: You can select typewriting or install other typewriting: Date/Time: Set the Date/time of the Tester. IP setting: Manually set the IP address, Sub-net Mask, Default Gateway and DNS address or select “Dynamic allocation”...
Page 110 (192.168.5.0) and (192.168.1.0). Volume: Set volume level. SD Card: Displays SD Card Capacity. You can also format the SD card or unmount it before removing FTP server: Once the tester connects to a network, a computer can be used to read the SD card files via FTP.
Page 111: File Explorer
Online Registration: Online update need register first, after the tester connect to network, then fill registration information to register. User Feedback: if you have any comments or suggestions for the tester, please connect it to network and write your feedback. Lock Screen: the meter default is not locked.
Page 112 It includes Music, Videos, Pictures, Documents, zip file etc. It is convenient to view and manager. FTP server You can choose internal or external SD card. Other operation details,please refer to FTP settings. Page.107.
Page 113: Audio Test
3. 4 Audio test You can test the audio input from audio pickup devices by connecting the audio pickup device to the tester with the supplied audio cable. 3.5 HDMI output The built in HDMI output port can output live video from an analog or IP camera, recorded files, media files and images to HDTV monitors.
Page 114: Dc12V 2A Power Output
The instrument’s PoE maximum power output is 24W. If Ultra- high-power load happens, the tester will enter protection mode . 3.7 DC12V 2A power output When the IPC tester is turned on, the DC 12V power output ON by default. The smaller end of the supplied converter cable connects to the tester’s DC12V/2A OUTPUT and the other end connects to the camera’s power input.
Page 115: Usb 5V 2A Power Output
Application Power output function is mainly used in the camera field demonstration and testing, meanwhile, for some cameras installation sites, If there is no power outlet for the adapter to power the camera, the tester can offer temporary power for it. But we do not suggest tester supply power for a long time. Notice: Don’t input any power into the “DC12/2A OUTPUT”...
Page 116 The user manual in the accessory bag is for reference only, please refer to the electronic version in the disk for updated information. The user manual in the accessory bag is for reference only, please refer to the electronic version in the disk for updated information.

Dahua DH-PFM906-E User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Dahua DH-PFM906-E

Summary of Contents for Dahua DH-PFM906-E

Table of Contents