Page 1 Integrated Mount Tester User Manual （V1.0）...
Page 2 Thank you for purchasing the Integrated Mount Tester. Please read the manual before using the Integrated Mount Tester and use properly. For using the Integrated Mount Tester safely, please first read the 「 Safety Information」 carefully in the manual. The manual should be kept well in case of reference. Keep the S/N label for after-sale service within warranty period.
Page 3: Table Of Contents
Content 1 .Safety Information------------------------------------------------------------------------------------------------- 1 2. Integrated Mount Tester Introduction--------------------------------------------------------------------------- 3 2.1 General------------------------------------------------------------------------------------------------------- 3 2.2 Features------------------------------------------------------------------------------------------------------ 3 2.3 Function------------------------------------------------------------------------------------------------------ 6 2.4 Packing list------------------------------------------------------------------------------------------------- 14 2.5 Function interface----------------------------------------------------------------------------------------- 15 3. Operation-----------------------------------------------------------------------------------------------------------18 3.1 Installing the Battery--------------------------------------------------------------------------------------18 3.2 Instrument connection------------------------------------------------------------------------------------ 19 3.2.1 IP camera connection------------------------------------------------------------------------------ 19 3.2.2 Analog camera connection------------------------------------------------------------------------ 20 3.2.3 HD Coaxial camera connection-------------------------------------------------------------------20 3.2.4 HDMI IN-------------------------------------------------------------------------------------------- 21...
Page 4 3.3.13 SDI Camera test----------------------------------------------------------------------------------59 3.3.14 CVI camera test---------------------------------------------------------------------------------- 61 3.3.15 TVI camera test---------------------------------------------------------------------------------- 67 3.3.16 AHD camera test---------------------------------------------------------------------------------69 （1） IP address scan------------------------------------------------------------------------------71 3.3.17 Network tool------------------------------------------------------------------------------------- 71 （2）PING test--------------------------------------------------------------------------------------- 72 （3）Network test------------------------------------------------------------------------------------72 （4）Port Flashing----------------------------------------------------------------------------------- 76 （5）DHCP server----------------------------------------------------------------------------------- 77 （6）Trace route------------------------------------------------------------------------------------- 77 （7）Link monitor----------------------------------------------------------------------------------- 78 3.3.18 Rapid IP Discovery------------------------------------------------------------------------------79 3.3.19 PoE power / DC12V 2A and DC 5V 2A USB power output------------------------------ 79...
Page 5 3.3.35 Dahua test tool----------------------------------------------------------------------------------106 3.3.36 Update------------------------------------------------------------------------------------------- 110 3.3.37 Office-------------------------------------------------------------------------------------------- 111 3.3.38 LED Flashlight--------------------------------------------------------------------------------- 111 3.3.39 Browser------------------------------------------------------------------------------------------112 3.3.40 Notepad------------------------------------------------------------------------------------------112 3.3.41 System setting---------------------------------------------------------------------------------- 113 3.3.42 File explorer------------------------------------------------------------------------------------ 117 3.3.43 Theme--------------------------------------------------------------------------------------------118 3. 4 Audio test------------------------------------------------------------------------------------------------ 121 3.5 HDMI output--------------------------------------------------------------------------------------------- 121 3.6 PoE power output---------------------------------------------------------------------------------------- 122 3.7 DC12V 2A power output------------------------------------------------------------------------------- 122...
Page 6: Safety Information
1 .Safety information ◆ The tester is intended to use in compliance with the local rules of the electrical usage and avoid to apply at the places which are inapplicable for the use of electrics such as hospital, gas station etc. ◆...
Page 7 resistance, capacitance, diode, continuity, otherwise it will damage the meter. ◆Never perform capacitance measurements unless the capacitor to be measured has been discharged fully. ◆Never measure any of resistance, capacitance, diode or continuity measurements on live circuits. Visual laser sources When you turn on visual laser sources, please don’t stare at it, or will damage to eyes When not using it, please turn it off and cover the protective cap .
Page 8: Integrated Mount Tester Introduction
2. Integrated Mount Tester Introduction 2.1 General The 7 inch touch screen Integrated Mount Tester is designed for maintenance and installation of IP cameras, analog cameras, TVI, CVI AHD, SDI cameras, as well as testing 4K H.264 camera by mainstream, The 1920x1200 resolution enables it to display network HD cameras and analog cameras in high resolution.
Page 9 Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify  unactivated hikvision camera, also can display image from the Hikvision camera. DH test tool app is design for Dahua Camera test, and modify IP, user name and password  parameters etc.
Page 10 call camera OSD menu AHD camera image display, 4Xzoom, video record and playback, Coaxial PTZ control and call  camera OSD menu HDMI signal output, supports up to 1080P.  Analog camera image display, auto adapt and display the video format of NTSC/PAL ...
Page 11: Function
Cable test , Test LAN cable or telephone cable,UTP cable etc ,cable type and the sequence of  wires will be displayed Support RS485,rate 600 ～ 115200bps adjustable  PTZ protocol analysis, control protocol command displays to check RS485 transmission ...
Page 12 2.3.5 RJ45 cable TDR test RJ45 cable TDR test and cable quality test, to test cable pair status, length, attenuation reflectivity, impedance, skew and other parameters. 2.3.6 Screen capture Screen capture, long press the key “enter”, can capture screen interface and save it in any time. 2.3.7 12V power input test Show the current adaptor input voltage and power.
Page 13 Hik test tool app is design for activating and debugging Hikvision camera, can auto-identify unactivated hikvision camera, also can display image from the Hikvision camera. 2.3.24 DH test tool DH test tool app is design for Dahua Camera image test, modify IP, user name and password parameters etc. Page.8.
Page 14 2.3.25 IP camera test The device is designed for ONVIF IP camera testing. It can display the image from an IP camera and change the IP address. The 7 inch 1024x600 screen display allows the user to view the image with a sufficient screen size. With the ONVIF tool, you can display the image from an IP camera and use the PTZ functions.
Page 15 COLOR BURST level: Testing the color burst level will determine if the burst signal is sufficient to trigger the displays color producing circuit. Burst will diminish in amplitude over longer cable runs and can get fall below the threshold for the video display to show a color image. For NTSC format, the Chroma standard level is 40 IRE For PAL format, the Chroma standard level is 280mV If the Chroma level is too low, the color will not be as deep, and some details of the image will get...
Page 16 2.3.32 PTZ data analysis Search the Control protocol code from Multifunction keyboard or DVR by RS485 interface, test the PTZ control command data whether received anomaly and RS485 data transmission. Screen displays 16 hexadecimal codes such as PELCO-P:A0 00（Add） xx xxxxxx AF xx PELCO-D:FF 01（Add）xx xxxxxxxx 2.3.33 Digital Image zoom on the monitor Set image zoom up to 4X to get a closer look at all the image detail.
Page 17 2.3.39 IP address scan The IP address scan can quickly search for connected IP cameras or another network device IP address. 2.3.40 PING Test PING is the most conventional network debugging tool, it is used for testing if the connected IP camera or other network equipment is working normally and the IP address is correct.
Page 18 2.3.46 LED Flashlight Press the LED On/Off button to use the LED flashlight. 2.3.47 TDR cable test TDR cable testing, accurately measure BNC cable, network cable, controls cable’s open circuit and short-circuits location,it greatly improves working efficiency. 2.3.48 WIFI With built in WIFI, you can view the video from a wireless camera (ONVIF or customized camera) or connect to a Wireless network.
Page 19: Packing List
2.3.55 Network bandwidth testing The network bandwidth test needs two tester meters to test bandwidth: one as a transmitter, the other as a receiver. 2.3.56 Cable Tracer (cable search) Cable identification by use of an audio signal. This function enables the blue cable tracer to find the connected cable from a bundle of cables with an audio tone.
Page 20: Function Interface
2.5 Function interface Press more than 2 seconds, turn on or off the device ,short press to turn on or off the menu display Menu key 4xzoom the image displays. Far focus: Focus the image faraway Near focus: Focus the image nearby TELE: zoom in the image WIDE: zoom out the image Open/set ,Confirm the setting of parameters, open or enlarge the aperture...
Page 21 downward Confirm key Return/Close : Return or cancel while setting parameters of the menu, close or decrease the aperture Multimeter interface The charge indicator: it lights red while the battery is being charged. As the charging is complete, the indicator turns off automatically The RS485 data transmission indicator: it lights red while the data is being transmitted The data received indicator: it lights red while the data is being received...
Page 22 RS485 Interface: RS485communication for the PTZ HDMI IN Video signal output（BNC interface）/ cable tracer interface CVBS input /AHD /TVI/CVI Coaxial interface Optical power meter interface PoE power supply output or LAN test port (Use to test PoE or non-PoE IP camera) PSE power sourcing equipment.
Page 23: Operation
3. Operation 3.1 Installing the Battery The tester has built-in lithium ion polymer rechargeable battery. The battery cable inside battery cabin should be disconnected for safety during transportation! Prior to the use of the instrument, the battery cables inside the battery cabin should be well connected.
Page 24: Instrument Connection
3.2 Instrument connection 3.2.1 IP camera connection Power an IP camera with an independent power supply, then connect the IP camera to the tester’s LAN port, if the link indicator of the tester’s LAN port is green and the data indicator flickers, it means the IP camera and the tester are communicating.
Page 25: Analog Camera Connection
3.2.2 Analog camera connection (1) ) Connect the camera's video output to the tester’s VIDEO IN. The image will display on the tester after pushing the PTZ icon. (2) Tester’s “VIDEO OUT” interface connect to the Video input of monitor and optical video transmitter and receiver, the image display on the tester and monitor.
Page 26: Hdmi In
(1) Connect the SDI camera's video output to the tester’s “SDI IN” interface, the image will display on the tester. The tester only come with SDI input interface. There is no SDI output interface. (2) Connect the SDI camera or the speed dome RS485 controller cable to the tester RS485 interface, (Note: positive and negative connection of the cable).
Page 27: Osd Menu
3.3 OSD menu Press the key 2 seconds to turn on Press the key again to turn off short press the key to enter sleep mode, press it again to test. If tester works abnormally and cannot be turned off , Press the key several seconds to turn off, the tester reset.
Page 28 In lite mode, click the finger icon in the lower right corner to release lock icon, move icons and  change function icons sequence. Normal mode Tap the screen and slide left or right to change menu.  In normal mode, press icon several seconds, go screen management status. Change icons sequence and move it to common tools bar.
Page 29 Create New Folder: Drag the icon to the folder in top right corner, enter the folder name,icon will be auto placed in the new named folder. Press the folder several seconds, to change the folder name, you can move the icon out of folder, the folder will be auto deleted until move out all icons.
Page 30: Drop-Down Menu
3.3.2 Drop-down Menu Press and slide at right top right corner twice to open shortcut menu. The shortcut menu includes POE power output, IP settings, Wi-Fi, HDMI IN, CVBS, Video OUT, LAN, Brightness, settings etc. HDMI: Click HDMI IN to enter ， in HDMI IN mode, It can converter test from analog to digital with dual test window IP &...
Page 31: Short Cut-Menu
Brightness: Set brightness Settings: Enter settings interface. IP: Enter IP Settings interface. POE power output: Turn on or off the tester “PoE power “app WLAN: Turn on WLAN net and displays current WLAN status. 3.3.3 Short cut-menu You can call shortcut menu by press tester’s “menu” key, you can self- define shortcut menu. Press the key“...
Page 32: Screen Capture
Short cut-menu setting, you can long press any app in the all applications list ,it will auto move to shortcut menu . If delete any app in the shortcut menu ,please select a app and press several seconds ,it will be deleted. 3.3.4 Screen capture Long press the key “enter”, can capture screen interface and save it in any time.
Page 33 PC screen projection： Install VLC player in the PC, turn on the VLC player "Media - Open Network Streaming", and input the RTSP address of on the top instrument two-dimensional code, click "play" to view the screen real-time projection. (you also can install “VLC player” in the mobile phone , tester and mobile phone display at the same time) Page.28.
Page 34: Rapid Video
video 3.3.6 Rapid Press enter function, One key to detect all network cameras and auto play the images. Auto log in and display camera image. Detailed operation refer to ONVIF function. After exit ONVIF app, Click Refresh to search ip address. Page.29.
Page 35: Ip Discovery
discovery 3.3.7 Press IP discovery ,tester auto-scan the whole network segment IP, as well as auto-modify the tester‘s IP to the same network segment with the scanned camera's IP. Local IP：Tester’s IP address, Tester can auto-modify the tester‘s IP to the same network segment with the scanned camera's IP.
Page 36: Rapid Onvif Test
, it can auto-scan the whole network segment IP, and auto-modify tester’s IP address , greatly improved engineering efficiency. ONVIF test 3.3.8 Rapid Rapid ONVIF can display 4K H.264 camera image by tester mainstream, one key to activate Dahua camera. Press enter ONVIF function, the meter auto scan all ONVIF cameras in different network segments.
Page 37 Click the button “Refresh”, tester will scan the ONVIF camera again. Click the newly displayed ONVIF camera on the “Device List“. The tester will show the IP camera’s relative information and settings. Pop-up settings menu when click the “ONVIF setting ”icon in the upper left corner Across network segments scan: After open this function , enter “Setting - IP Settings - Advanced”to add other network segments IP, Rapid ONVIF function can across network segments to scan camera’s Auto Login : After open this function, tester can auto login camera and display camera image.
Page 38 Video transmission protocol: UTP and TCP protocol. Open password cracker : Cracks password of cameras. View manual : Open Manual. Restore Defaults: Revert “Rapid ONVIF” to default settings. Confirm : Save the modified parameters. Click “MENU”icon to open camera setting . While in the “Live video”...
Page 39 ONVIF PTZ control: Tap the image in the direction you want the PTZ camera to move. Tap the left side of the image to move left, right to go right, up to go up and down to go down. Compatible IP PTZ cameras will rotate accordingly.
Page 40 Image setting: Click “Imaging Set” to adjust image brightness, saturation, contrast, sharpness and backlight compensation mode. Profiles：Click “profiles"，can view video streaming current configuration files, as well as switch between Major stream and minor stream. Page.35.
Page 41 Preview pictures：Quickly preview and zoom in or out pictures, automatically and manual refresh. Identification: click “Identification” to view information of the camera. Time set: click “Time set”, Select " Manual set" to set up the time of camera. Page.36.
Page 42 Maintenance: For camera software reset or restore to factory settings. User Set: Modify camera user name ,password etc parameters. Page.37.
Page 43 Network setting：Click “Network Set “to change the IP address. Some cameras cannot support change IP address, so there is no change after saving. Zoom in image :press the key to enter the zoom mode. Press it again to exit zoom mode.When the image is enlarged tap left, right, up or down on the image to move the whole image on the screen.
Page 44 When the image is enlarged, if not operate on touch screen, it can operate by the keyboard ,press the to zoon in , press the key to zoom out ,press upward and downward key to move image. If it is network video input to the tester, as the tester supports resolution up to 1080p, the input image will be very clear after it is enlarged.
Page 45 Snapshot：Click bottom“snapshot” to screenshot the image and store it in the tester. if select manual storage, appears dialog box “Input Name” , user-defined the files name(by Chinese character, English letter or digit ) to save in the tester, if select “Auto- storage”,the tester auto stores the files after snapshot.
Page 46 Video files can play in the Video player on the main menu. Set preset position :Move the camera to preset position, enter the preset number on the Bottom right corner to complete position preset. Call the preset position : Select the preset number on the left, click "Call"to call preset. PTZ Speed set : Horizontal and Vertical Speed set.
Page 47 RTSP: Get RTSP address of the current camera. Doc: Auto create testing reports document of camera, click "Create document”. Click Preview to view the report document. Enter the camera test information, click "Create Document" to complete the report. Page.42.
Page 48: Ip Camera Test
Display image from the 4K camera by main stream Click icon to enter IP camera test Note: Currently, the Test App only supports some brands’ specific IP cameras, these include specific models made by ACTI, AXIS, Dahua, Hikvision, Samsung, and many more. If the camera is Page.43.
Page 49 “Manual”：Click IP camera type, list Honeywell , Kodak,Tiandy, Aipu-waton, ACTi,WoshiDA IP camera etc. If the brand has offered official original protocols, pls select camera type, input IP camera address ,user name and password ,click” official” to enter the camera image display interface(Currently, only support DAHUA official protocols ). Page.44.
Page 50 Stream code: When test camera via RTSP, you can select mainstream or sub stream to test (if camera’s RTSP have not been start or without, it will tip “auto match fail, please witch to manually selecting. IP Camera's IP: Enter the IP camera’s IP address manually or click “Search” to auto-scan for the IP camera’s IP address.
Page 51: Hdmi In
If IP address setting has error or IP camera is not connected.. The tester prompts “Network Error”. Click to quit from image display and return to the Tester interface. Once you are viewing video on the Tester app, you will see the “Video Menu” icon on the top right.
Page 52 (2) Video record When you click the “Record” icon, video starts recording. A red recording icon appears on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on the “Record” icon again to stop recording and save the video file in the tester. If select manual storage, before recording begins ,appears dialog box “Input Name”...
Page 53 (3)Photo Click the icon “photo” to enter, click the selected thumbnail photo to display it on the screen. Double-tap the image can view full screen. Double-click again the photo to return. To rename or delete an image, click and hold on the file until this screen below appears Click to close and return to PTZ controller.
Page 54: Video Monitor Test
To rename or delete a video, click and hold on the file until this screen appears: Video files also can play in the main menu “Video Player". 3.3.11 Video monitor test Analog camera test and PTZ control, click icon to enter Page.49.
Page 55 Display the input video image, click the top menu bar icon to enter video level meter (PEAK level, SYNC level, COLOR BURST measurement) Select relative function on the right side Toolbar to operate , functions including “Photos”, “Snapshot” , “Record” , “Playback” , “PTZ” , “Set” , Click , or press to quit.
Page 56 A. Protocol Use the up and down arrow keys to move the yellow cursor to the “protocol ”, set corresponding Protocol and support more than thirty PTZ protocols. Such as Pelco-D,Samsung,Yaan,LiLin,CSR600,Panasonic,Sony-EVI etc. B. Port Click and move, to “port” Select the communication port for the PTZ camera controlling (RS485) C.
Page 57 PTZ Control: Press the key control the PTZ direction of rotation Press the key , to switch on or turn off the aperture. Press the key , adjust the focus manually Press the key , manually adjust the zoom (2) Video and storage setting Click icon “set”,to enter and set analog video image brightness , contrast, color saturation, as well as the file storage way after snapshot and recording, support auto-storage and manual storage.
Page 58 If not use touch screen to operate, press the key to zoom out , press the key zoom in, press upward and downward key to move the image. For analog video input, as the resolution is 720*480, it is normal that the zoom in image is not clear.
Page 59 (5) Video record When you click the “Record” icon, video starts recording. A red recording icon appears on the screen and begins to flash and a timer appears indicating the time elapsed for the video. Click on the “Record” icon again to stop recording and save the video file in the tester. If select manual storage, before recording begins ,appears dialog box “Input Name”...
Page 60 To rename or delete an image, click and hold on the file until this screen below appears Click to close and return to PTZ controller. (7) Recorded video playback Click the “Playback” icon to view your recorded videos. Tap on the video file image you want to watch. To rename or delete a video, click and hold on the file until this screen appears: Page.55.
Page 61 Video files also can play in the main menu “Video Player". (8) Video level meter Click the icon to enter, the Integrated Mount Tester has adopted hardware high-speed sampling and processing technology, can perform both NTSC and PAL video amplitude signal measurements for PEAK to PEAK, SYNC levels and COLOR BURST chroma level.
Page 62 Video signal level 140±15IRE NTSC Chroma level( COLOR BURST) 40±5IRE SYNC signal level 40±5IRE Video signal level 1000±200mV Chroma level( COLOR BURST) 300±35mV SYNC signal level 300±35mV Video signal PEAK to PEAK level: For NTSC format, the video signal level is 140±15IRE For PAL format, the video signal level is 1000±200mV If the level is too low, it will cause the image to lose quality and limit the distance it will travel over cable.
Page 63: Color-Bar Generator
lighter. If the Chroma level is too high, there will be distortions on the image. If the coaxial cable is too long, it will reduce the chroma level. Image loop test：Test video optical transmitter and receiver and video cable, connect one end to the tester “VIDEO OUT”...
Page 64: Sdi Camera Test
BNC loop test: Tester can send and receive color bar generator through the tester’s “video out and video in” port, it is for testing transmission channels, such as video Optical, video cables etc. The tester “VIDEO OUT” port to connect optical terminal’s sending port, and “VIDEO IN” Port to optical terminal’...
Page 65 When tester receives SDI camera image, it will display the image data. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows: 1280x720P 25Hz 1280x720P 30Hz 1280x720P 50Hz 1280x720P 60Hz 1920x1080P 25Hz 1920x1080P 30Hz 1920x1080I 50Hz 1920x1080I 60Hz The tester’s HDMI output port can be used as SDI to HDMI converter, output HD SDI image to HD TV...
Page 66: Cvi Camera Test
3.3.14 CVI camera test HD CVI camera, CVI dome camera test and PTZ control, click icon to enter When HD CVI signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows 1280x720P 25FPS / 1280x720P 30FPS / 1280x720P 50FPS / 1280x720P 60FPS 1920x1080P 25FPS / 1920x1080P 30FPS/2560x1440P 25FPS/30FPS.
Page 67 Enter PTZ address to perform parameters setting. Operation instructions, please refer to “3.3.1 PTZ (1) Video monitor test”. The PTZ address in the tester must be consistent with the dome camera or decoder, then the tester can test .After setting the parameter, the tester can control the PTZ and lens. Page.62.
Page 68 To control PTZ by screen touch: Tap left, right, upward and downward on the touch screen to control the PTZ rotation direction, PTZ cameras will rotate accordingly. By two fingers move outward and inward on the touch screen to zoom in and out the PTZ.
Page 69 Call preset position Tap the preset position: Tap the preset position area, input preset position number. Tap “call position” to complete call preset position. Page.64.
Page 70 1.2 RS485 control Operation instructions, please refer to “3.3.1 PTZ (1) PTZ control parameters setting”. （2）Coaxial camera menu setting Tap icon “UTC””, select “menu setting” to enter the dome camera menu. Input calling dome camera menu address code, after finishing the parameter settings, you can press the or click the icon to call the dome camera menu .
Page 71 Press arrow keys to set. (3) Snapshot, record, photo viewer and video play back, please refer to “3.3.1 PTZ (1) Video monitor test”. Page.66.
Page 72: Tvi Camera Test
Tap “close menu” or press the key “ ”to close camera menu. (4) Save setting Click icon “Set” on the right toolbar to enter storage setting. Support auto-storage and manual storage. When select manual storage, user can name and store the files. 3.3.15 TVI camera test HD TVI camera, TVI dome camera test and PTZ control, Click icon to enter...
Page 73 When HD TVI signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows: 1280x720P 25FPS / 1280x720P30FPS / 1280x720P 50FPS / 1280x720P 60FPS 1920x1080P 25FPS / 1920x1080P 30FPS / 1920x1080P 50FPS / 1920x1080P 60FPS /2048x1536 18 FPS.
Page 74: Ahd Camera Test
Input calling dome camera menu address code, after finishing the parameter settings, you can press the or click the icon to call the dome camera menu. More operation instructions (such as PTZ control, coaxial camera menu setting ,snapshot, recording and playback etc), please refer to“3.3.6 CVI camera test”.
Page 75 When AHD signal input, the tester will display the image resolution on the top bar. Double-taps on the screen to make the image displayed full screen. The tester supports resolution as follows: 1280x720P 25FPS / 1280x720P 30FPS / 1920x1080P 25FPS / 1920x1080P 30FPS/2560x1440P 15FPS,25FPS,30FPS.
Page 76: Network Tool
“PTZ” cannot control , pls go “PTZ-2” ) If to coaxial PTZ control the AHD camera, no parameters setting is needed. More operation instructions please refer to “3.3.6 CVI camera test”. 3.3.17 Network tool （1）IP address scan Connect the cable to the LAN port, click icon to enter, Set your IP address search range by changing the Start and End IP addresses.
Page 77: 2）Ping Test
（2）PING Test PING is the most conventional network debugging tool; it is used for testing if the connected IP camera or other network equipment’s Ethernet port is working normally and the IP address is correct. Connect a network cable to the LAN port and click the icon to open the PING tool.
Page 78 When test, need a tester or a computer installed Network Test Software as the Server, the other tester sends packet test. The two testers must be in the same network segment. a).Start the server: Click “Start Server” button to use the tester as a Server. It will display its IP address at the top of the screen.
Page 79 Network bandwidth testing can also be tested with a computer using compatible network bandwidth testing software. Install network bandwidth testing software on a computer, as a test Client or Server, to do the mutual testing with the tester. If use computer as the server, the computer IP address is :192.168.0.39 Tester as Client, tester’s IP address is:192.168.0.238.
Page 80 Or use tester as a Server, computer as test Client（select Client, input tester’s IP address to test） When use tester as Server,shows results: Page.75.
Page 81: 4）Port Flashing
（4）Port Flashing Connect a network cable to the meter’s “LAN” port, click the icon to open the Port Flashing app. Click “Start”. The Integrated Mount Tester sends a unique signal to make the connected LAN port of the switch flash. If the tester and PoE switch are connected well, the LAN port of POE switch flash at special frequency, If not, no any changes on the LAN port.
Page 82: 5）Dhcp Server
（5）DHCP server Click on the DHCP icon to open the DHCP server app. Select the “Start” check box at the top and make any desired changes to the network settings. Click “Save” to start assigning dynamic IP addresses for IP cameras and other networked devices. Click the “Refresh” button to check your Client list. （6）Trace route It is used to determine path of the IP packet access target.
Page 83: 7）Link Monitor
Click “start” to trace the goal address. （7）Link monitor Click the icon to open the Link Monitor app. This app is used to see if an IP address is occupied by other network devices. This will avoid new address conflicts. Click “Add”...
Page 84: Rapid Ip Discovery
Application: Add an IP camera or other network device to the current network group, the new IP address must not be occupied, otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied. 3.3.18 Rapid IP Discovery Connect the cable to tester’s LAN port.
Page 85: Cable Test
Note: 1. Don’t input power into the “DC12/2A OUTPUT” port. 2. Don’t output this DC12V/2A power to the DC12V/IN port of the Integrated Mount Tester to avoid destroy. 3. The Integrated Mount Tester power output is close to 2A, if the IP camera’s power is over 2V, the tester will auto enter protection mode.
Page 86: Rj45 Cable Tdr Test
Test LAN cable or telephone cable. Connect LAN cable or telephone cable with the Integrated Mount Tester and cable tester. And then the connecting status, cable type and the sequence of wires as well as the serial number of the cable tester kit will be displayed.
Page 87 Single test: test cable status, length and attenuation. Repeat test: continue to test cable status, length and attenuation. Status: after link up, screen display “online”, if not link up or open circuit, screen display ”open circuit”, if cable pair is short circuit, screen display “short circuit”. Length: the max test length is 180 meters, when cable is open circuit or short circuit, can test the cable length, if screen display “online”, the testing result would be not accurate.
Page 88 range is generally in 85-135Ω. Skew: After 1000M link up, when skew value is 0ns,it is the best quality communication, if over 50ns, will cause a Bit Error Rate in the transmission. Connection diagram: Cable sequence diagram: A straight- through and cross-over cable diagram, the cable sequence display for reference. Page.83.
Page 89: Cable Search
Click “Help”, check the instruction of all parameters. 3.3.22 Cable Search Connect test cable or BNC cable to the UTP port or the CABLE SCAN (VIDEO OUT) port on the bottom. Click icon to enter, click the Number on the screen to adjust audio type. Use the blue Combination cable identifier and network cable tester’s copper pointer to touch all the cables in the bundle .
Page 90: Tdr Cable Test
Note:Install two AAA batteries in your blue Cable Identifier. Note:While the cable tracer is receiving the audio signal from the tester, it may be induced into adjacent or crossing cables, however, the cable that makes the loudest noise is the one that’s connected to the meter.
Page 91 Built-in BNC cable, network cable, RVV control cable, Telephone line and TVVB cable etc can test, 11 groups user-defined cable can be set. Click “Cable” “Type” to select cable and start testing. One tap on “Start” do one testing. If select built in cable type for testing, click “+”...
Page 92 1.Select user-defined and click “Calibration “to enter test , click “user-defined 1”can define cable name,such as:AiPu BNC-5 2. Click “Cable” , “Type” to select cable, and corresponding type, for example, if testing BNC cable, select “BNC”, if testing communication cable 75-2, select SYV 75-2. 3.Click “+”or“-”...
Page 93: Poe Voltage Test
short circuit, help engineer quickly find the cable’s problem location. It is more convenient and efficient to repair the faulty cable. Note: The TDR reflect signal could be affected by the cable quality/ cable’s not well connected etc to cause the different TDR measurement, the TDR measurement is for reference only.
Page 94: Power Input Test
When PoE / PSE voltage testing, PoE/PSE conntect to the tester's PSE "IN" port , the camera connetct to tester's Lan port , tester not only can transmit voltage to supply power for camera ,but also transmit data at the same time. as well as the computer connect to the PoE/PSE, it can log in connected tester's PoE camera.
Page 95 1) SYMBOLS: U:DC Voltage Measuring A:DC Current Measuring Ω:Resistance Measuring :Diode Testing :AC Voltage Measuring :AC Current Measuring :Continuity Testing :Capacitance Measuring AC/DC Voltage and current measurement state display Auto- range The Multimeter auto adjust the range by input signal or tested components Data hold Hold data Display the relative measurement value...
Page 96 DC Voltage Measuring WARNING! You can’t input the voltage which more than DC 660V, it’s possible to show higher voltage, but it’s may destroy the inner circuit. Pay attention not to get an electric shock when measuring high voltage. a. Connect the black test lead to the “COM ” jack and the red test lead to the “V/Ω” jack. b.Select , enter the DC voltage measurement.
Page 97 C. DC Current Measuring (only manual range ) WARNING! Shut down the power of the tested circuit, and then connect the meter with the circuit for measurement. a. Connect the black test lead to the “COM ” jack and the red test lead to the “mA” jack for a maximum of 660mA current.
Page 98 a. Connect the black test lead to the “COM” jack and the red test lead to the“mA” jack for a maximum of 660mA current. For a maximum of 10A, move the red lead to the 10A jack. b. select , enter the AC current measurement, manually select the range c.
Page 99 Manual range:(Connect the red lead to black leads, will display the measure range) 000.0Ω  660Ω range 0.000 KΩ  6.600KΩ range 00.00 KΩ  66.00KΩ range 000.0 KΩ  660.0KΩ range 0.000 MΩ  6.600MΩ range 00.00 MΩ  66.00MΩ range F.
Page 100 d. Connect test red lead across to the cathode, the black lead to the anode of the diode under testing. e .Tested diode, forward voltage low 30mv,there is sound indication ,then can finish the testing quickly without view the screen. H.
Page 101 660uF, the Max time will be 6.6 seconds, if the capacitor is leaked or damaged, the data can’t be read. The tester will be normal after disconnecting the capacitor. Manual range and Auto range When testing, click “Range select " to change the value, click “Auto range “to enter Auto measurement.
Page 102: Optical Power Meter
if the current over the rated range ,fuse will melt to protect the meter .Pls use the same model when change the fuse, Pls opens the battery cover to change. Note: 10A socket without fuse protection, if over the current range. Wrong using the 10A socket to measure the voltage, will damage the meter.
Page 103: Visual Fault Locator
the displayed new measurement and relative value is red color. Press it again to quit. Data hold and Relative measuring use together, the data is yellow while the function is effect. 3.3.28 Visual Fault Locator Click icon to enter Page.98.
Page 104 VFL four status can select——“Steady mode”, “Evasive 1Hz”,“Evasive 2Hz”and“Time off”. Click button “Steady mode” to enter steady status, click button “Evasive 1Hz” and “Evasive 2Hz, to enter pulse mode, click button “Time off”, VFL is turned off. Timed turn off can select (5 mins, 10 mins, 30 mins, 60 mins and 120 mins).
Page 105: Audio Record
Click icons “Evasive 1Hz”or“Evasive 2Hz”to enter pulse mode, the red laser source is emitted by a certain frequency, press it again to quit. 3.3.29 Audio Record Connect an audio device to the Integrated Mount Tester’s audio input port. Click the icon to enter the Audio Recorder app.
Page 106: Audio Player
Click “Setting” to choose the baud rate of RS485; it must be the same as the DVR or the Control. keyboard The DVR or Control keyboard send the code to the tester, if it can be read, the protocol will shown on the upper right, like Pelco D, if not, like P:--- While the tester receives the code, press the key to empty.
Page 107: Rtsp Player
The Media player can browse video and image files. It supports the video formats of MP4, H.264, MPEG4, and MKV. The Integrated Mount Tester recorded files can play directly via the Media player. The Media player will automatically display the video files from the tester Click on the desired file to play.
Page 108 Local IP: This is the Integrated Mount Tester’s IP address. RTSP Add: This is where you can manually enter the IP camera’s RTSP URL or click on Search to search the network for cameras that use an RTSP stream. IPC Username: Enter the IP camera’s user name. IPC Password: Enter the IP camera’s password.
Page 109: Hik Test Tool
3.3.34 Hik test tool Hik test tool app is designed for activating and debugging Hikvision camera, can auto-identify unactivated hikvision camera, also can display image from the Hikvision camera. Tap icon to enter 1. Hikvision activation ： When connect the unactivated Hikvison camera to the tester, it will auto identify and display “Unactivate”...
Page 110 3. Confirm activation After activating the camera, the program default modifies the camera IP. Activated multiple cameras in the local area Network, and pop-up menu to modify IP, improve project efficiency. Play: Display image from the camera. Modify network information: Change the camera IP address, sub-net mask and gateway etc. Modify user information: Modify the camera's user name and password.
Page 111: Dahua Test Tool
Camera factory reset 3.3.35 Dahua test tool Dahua test tool is developed for installation and debugging of the Dahua IP camera, it can display image, and modify IP, user name and password etc. Making Dahua camera test more convenient and quickly.
Page 112 Select the camera of the online detection menu, if the camera support non-verification login, you can click “play” directly, and view the image. Pop up stream menu, select mainstream or second stream to test. Page.107.
Page 113 If the camera not supports non-verification login, pls select “camera” of online detection menu, and input correct user name and password, then click “log in”. After logging successful, you can test it. Play: select mainstream or seconded stream, IP camera live video display. Modify network information: modify camera parameter, such as ip address, subnet mask, gateway etc.
Page 114 Modify user information: modify camera user name and password, which is onvif, Dahua test tool, the tester user name and password, not web user name and password. Factory reset setting: camera will be soft reset, and the device’s user name, password and network set be saved.
Page 115: Update
3.3.36 Update Copy the downloaded update file to SD card "update" directory, if no directory, please create one. Click the icon to open the Update menu. Select “Local Update” to update via the SD card or select “Online Update” to check for updates on the internet. If there are applications that need updating, the applications will be displayed on the screen.
Page 116: Office
3.3.37 Office Quick office app (support excel, word, ppt format) doc. editable 3.3.38 LED Flashlight It is convenient for the installation or maintenance in the evening or in the dark. Click icon enter. While in the flashlight app, click the red button to turn on the LED lamp. Press it again to turn it off. If you don’t press the red button to shut off the lamp and press the button to exit the app, the lamp will stay on.
Page 117: Browser
3.3.39 Browser Click icon to enter Type in the camera’s IP address and press “Go” to access the IP camera’s interface. NOTE: You will not be able to view live video in the web browser. For viewing video, use the tester‘s live camera view Apps.
Page 118: System Setting
pls click to view the notepad , all saving contents display. Click each record bar to show the details. Press the record bar for several seconds, prompt whether delete it. 3.3.41 System Setting Click icon to enter Language: Select your desired language: English, Chinese, Korean, Russian, Italian , Polish ,Spanish, French or Japanese.
Page 119 Date/Time: Set the Date/time of the Tester. IP setting: Manually set the IP address, Sub-net Mask, Default Gateway and DNS address or select “Dynamic allocation” to use DHCP. To test multiple network segments, click “Advanced” and then click “Add” to enter another IP address for the Tester. After setting an advanced IP address (refer to the photos above), the unit can test two network segments (192.168.5.0) and (192.168.1.0).
Page 120 Select and press “WIFI” several seconds, to set static IP address. Wi-Fi hotspot: input “SSID” name and “password”, and then click “ok”to create Wi-Fi hotspot. Brightness: Set the desired brightness of the tester and adjust the sleep time settings. Volume: Set volume level. SD Card: Displays SD Card Capacity.
Page 121 Start the FTP server and then input the tester’s FTP address in the PC’s address bar. This will enable the PC to read ,copy and edit the files from the SD card without the use of SD card reader. Version information: Shows applications version information, if press any apps icon several seconds to uninstall.
Page 122: File Explorer
Lock Screen: the meter default is not locked. You can choose password Lock screen, pattern Lock screen or “NO” . Password Lock Screen: Set password, you can input digitals, letters or characters as password, input it again to confirm .when the meter is in standby mode or turn it on, you can input your password to enter. Pattern Lock Screen: Drawing a pattern to lock.
Page 123: Theme
FTP server You can choose internal or external SD card. Other operation details, Pls refer to FTP settings. 3.3.43 Theme Click Theme icon to enter themes setting. Desktop style : you can select Lite mode or normal mode. Theme: Page.118.
Page 124 Pressing square area’s any color icon several seconds, the selected color icon will be auto move the rectangle area, if you press selected color several seconds, and it will be auto deleted. Theme colors include fixed order and random order, and click “set” to save. Color When set background color, you can select colors from Color Phase, and also can input color’s RGB to set.
Page 125 Set as desktop background: Setting color as desktop background. Set as application background: Set color as application background. Set at the same time: Setting color as desktop background and application background. Cancel: Cancel current setting. Picture: Click Picture to select one, and set as temporarily background to view setting effect. Click “more” to select pictures from local file, and click set to set picture as background.
Page 126: Audio Test
effect etc, selecting one of effect to view slide effect in the square area, and click “set” to save. 3. 4 Audio test You can test the audio input from audio pickup devices by connecting the audio pickup device to the tester with the supplied audio cable.
Page 127: Poe Power Output
3.6 PoE power output The tester supports PoE (Power over Ethernet) output to an IP camera via the LAN port. Data transmission and POE 48V use the network cable’s 1, 2, 3, and 6 pins to deliver power. If the IP camera supports PoE, you can directly connect to the camera without the use of an external power supply.
Page 128 Application Power output function is mainly used in the camera field demonstration and testing, meanwhile, for some cameras installation sites, If there is no power outlet for the adapter to power the camera, the tester can offer temporary power for it. But we do not suggest tester supply power for a long time. Notice: Don’t input any power into the “DC12/2A OUTPUT”...
Page 129: Specifications
Activate Hikvision camera, display image from the camera, modify IP, user Hik test tool name and password parameters etc DH test tool Dahua camera test, modify IP, user name and password parameters etc IP camera type ONVIF,ONVIF PTZ SDI/EX-SDI video 1 channel SDI input（BNC interface）, resolution support : 720p 60fps /...
Page 130 signal test 1080p 60fps /1080i 60fps 1 channel CVI input（BNC interface, resolution support 720p CVI video signal test 25,30,50,60fps/ 1080p 25,30fps/2560x1440p 15fps,30fps 1 channel TVI input（BNC interfce）,resolution support 720p TVI video signal test 25,30,50,60fps/ 1080p 25,30fps /2048x1536 18 fps 1 channel AHD input（BNC interface）,resolution support 720p 25,30fps / AHD video signal test 1080p 25,30fps/2560x1440p 15fps,25fps,30fps Analog video test...
Page 131 1 channel audio signal input and 1 channel audio signal output to connect Audio test headphones Support RS485 control, Baud 600-115200bps, Compatible with more than PTZ control 30 protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc Output one channel PAL/NTSC color bar video signal for testing monitor or Color bar generator video cable.(red, green ,blue, white and black color ) Test UTP cable connection status and display on the screen.
Page 132: Multi-Meter Specifications
Auto off 1-30 (mins) General Working -10℃---+55℃ Temperature Working Humidity 30%-60% Dimension/Weight 255mm x 160mm x 46mm / 0.95Kg 4.2 Multi-meter specifications Counts:-6600～+6600 Conversion rate: 3times/s Current modes for clamp meter with ZERO function Isolation: the Multi-meter connector must be isolated with the other connector. DC voltage Range Accuracy...
Page 133 DC current Range Accuracy Resolution 6.600mA 66.00mA 10uA ±（0.5%+3） 660.0mA 100uA 10.00A ±（1%+5） 10mA AC current Range Accuracy Resolution 6.600mA 66.00mA ±（0.5%+3） 10uA 660.0mA 100uA 10.00A ±（1%+5） 10mA Resistance Range Accuracy Resolution 660.0Ω 0.1Ω ±（0.8%+5） 6.600KΩ 1Ω 66.00KΩ 10Ω ±（0.8%+2） 660.0KΩ...
Page 134: Optical Power Meter Specifications
Diode Range Resolution Function Schottky diode:0.15~0.25V 2.0V rectifier diode:0.6~1.0V triode PN junction:0.5~0.8V Capacitance Range Accuracy Resolution 6.600nF ±（0.5%+20） 66.00nF 10pF 660.0nF 100pF ±（3.5%+8） 6.600μF 66.00μF 10nF 660.0μF 100nF 6.600mF 1μF ±（5%+8） 66.00mF 10μF 4.3 Optical power meter specifications -70～+10dBm Measure Range(dBm) Wavelength(nm) 850nm,1300nm,1310nm,1490nm,1550nm,1625nm Detector...
Page 135: Visual Fault Locator Specifications
4.4 Visual fault locator specifications Laser type Wavelength Calibration 650nm Output power Modulation mode CW/1Hz/2Hz Measurement Range Connector FC/PC exchangeable Working Temperature －10℃～+55℃ Operating Temperature -20℃～+70℃ The data above is only for reference and any change of them will not be informed in advance. For more detailed technical inquiries, please feel free to call the Technical Department of our company.

Dahua PFM906 User Manual

Quick Links

Need help?

Questions and answers

Related Manuals for Dahua PFM906

Summary of Contents for Dahua PFM906

Table of Contents