Fienza Kaya 228111-LF Installation Manual

Warranties
Residential: Applies to domestic uses and applications of Fienza® products, such as private dwellings and
retirement villages.
Commercial: Applies to commercial uses and applications of Fienza® products, including, but not limited to:
commercial food premises such as restaurants; commercial accommodation such as hotels; hospitals and
healthcare facilities; public amenities; and industrial, laboratory
and manufacturing facilities.
Product Component Residential
LIFETIME replacement parts or product,
Ceramic Disc Cartridges
15 years labour
LIFETIME replacement parts or product,
Mixer (Structure Only)
1 year labour
LIFETIME replacement parts or product,
Finishes - Chrome
1 year labour
10 years replacement parts or product,
Finishes - PVD
1 year labour
5 years replacement parts or product,
Finishes - Electroplated
1 year labour
Accessories & Spare Parts 1 year replacement parts or product
NOTE: Excludes parts subject to general wear and tear such as O-rings, washers and jumper valves.
Warranty Conditions
Installation has been carried out by a licensed tradesperson in accordance with AS/NZS 3500 and all
●
applicable local regulations and plumbing codes.
All maintenance and adjustments to the product after the installation have been carried out by a licensed
●
tradesperson.
All care and cleaning instructions have been adhered to as prescribed.
●
Proof of purchase is required for warranty claims.
●
Warranty Limitations
To the extent permitted under the Trade Practices Act and other relevant legislation, Fienza's liability is limited
to: the cost of replacing the goods; or, the cost of obtaining equivalent goods; or, the cost of having the goods
repaired. Fienza is not responsible for any lack of operation or performance of goods (or any loss or damage)
where goods are used or adapted for use with other goods not supplied by Fienza. It is the responsibility of the
customer and installer before installation to ensure that all components are correct and free of obvious visible
faults. Fienza is not responsible for the labour and rectification costs incurred in the above circumstance.
Conditions for On-Site Warranty Service Calls
Fienza will charge a service fee for each visit to an installation by its technician where it is determined that the
fault is due to poorly executed or unlicensed installation, where the product is not a genuine Fienza product or
where the product is outside the warranty period. This may be paid in advance by credit card over the phone to
a Fienza technician attending the site and will be refunded if the Fienza product is found to be at fault.
PLEASE LEAVE THIS MANUAL WITH THE END USER
For more information, contact us or visit our website:
(07) 3490 6700 | help@fienza.com.au | fienza.com.au
Commercial
15 years replacement parts or product,
5 years labour
7 years replacement parts or product,
1 year labour
7 years replacement parts or product,
1 year labour
1 year replacement parts or product,
1 year labour
1 year replacement parts or product,
1 year labour
1 year replacement parts or product
Updated: 25/11/2024
Kaya
H O B - M O U N T E D O U T L E T & S E T S
For use with:
228111-LF Kaya Hob-Mounted Basin/Bath Outlet
228123-LF Kaya Squareline Hob-Mounted Basin/Sink Outlet
338101-LF Kaya Basin Tap Set
338106-LF Kaya Squareline Hob-Mounted Basin/Sink Set
230026-LF Basin Taps Hot/Cold Breach Set for Bench Taps/Levers (Contract Rotating)
IMPORTANT: Please read all of the instructions before installation. Check goods thoroughly before installation.
Installation of received goods that are damaged, warped or faulty will void warranty. Ensure all items meet your
plumbing requirements. This product is pre-assembled.
Do not disassemble, as this may void the warranty.
Watermark Scope of Use
This product must be installed by a qualified licensed plumber in accordance with the National Construction
●
Code Volume Three, AS/NZS 3500 and all applicable local regulations and plumbing codes.
The product is intended for residential and commercial indoor use only.
●
This product is manufactured to comply with the Lead Free requirements of the National Construction Code
●
Volume Three.
All pipe work must be thoroughly flushed prior to installation.
●
Do not remove the ceramic cartridge from the mixer when installing.
●
After installation all hoses and connections must be checked for leaks.
●
It is the responsibility of the installer to ensure a waterproof seal is achieved between the product and
●
mounting surface.
The flow controller incorporated in the outlet must be re-tightened to prevent removal by hand.
●
See below specifications for minimum and maximum operating pressures and temperature and other
●
installation requirements.
I N S TA L L AT I O N G U I D E